A Groundwork company - serving San Francisco, CA
M

Mr-Glass Construction Service in San Francisco, CA

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Why San Francisco Homeowners Choose Mr-Glass Construction

We provide independent Mr-Glass construction, repair, and installation service in San Francisco. Mr-Glass is a specialty glass and glazing fabricator, and its line centers on frameless shower enclosures, mirrored and glass wardrobe doors, glass railing systems, and insulated window and sliding-door units. That changes the trade. The crews who install and service Mr-Glass products work to glazier tolerances, not general-carpentry tolerances, and the difference shows up in how a panel is templated, set, and sealed. We route San Francisco homeowners to independent local pros who handle Mr-Glass products regularly, so the glass gets measured, templated, and sealed correctly the first time.

Call (866) 320-2646

Groundwork Construction Co. of San Francisco is an independent Mr-Glass service provider. We are not affiliated with, certified by, or authorized by Mr-Glass, and we say so plainly. Call (866) 320-2646 to talk through your enclosure, railing, or glazing project.

Why Trust Groundwork Construction Co. of San Francisco for Your Mr-Glass Construction?

Mr-Glass work rewards people who already know the hardware. Our technicians have up to 12 years of experience, and the independent local pros we route Mr-Glass work to handle the brand’s enclosure line and railing systems often enough to recognize a worn pivot or a failed wall channel before the homeowner does. They know the difference between a 3/8-inch and a 1/2-inch tempered panel, how a Neo-Angle entry sets into a corner, and why a mirrored wardrobe door that jumps the track usually needs a new roller rather than a new door.

Parts sourcing follows the job. We specify OEM-compatible hinges, pivots, sweeps, seals, and handle hardware for Mr-Glass enclosures, and the reason is mechanical rather than brand loyalty. The tempered panels are custom-cut and the OEM parts match the original hole spacing. Aftermarket hardware often means re-drilling glass, and re-drilling voids the panel.

Warranty-safe practice ties the whole thing together. Every project we handle is covered by our 730-Day Done Right Promise. If something isn’t done right, we make it right. That commitment runs two years past most handshake warranties, and it’s written, not spoken.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Common Mr-Glass Construction Problems We Fix in San Francisco

Glass failures look alike from a distance and aren’t. Here’s what we actually see on Mr-Glass products in San Francisco, and why the problems start.

  • Hinge-side sag on frameless hinged and pivot enclosures. A 3/8-inch or 1/2-inch tempered door is heavy, and it hangs off two or three points of hardware. When the wall behind it was never checked for plumb, the door slowly drops out of plane, drags on the fixed panel, and eventually clips the jamb. The pivots aren’t always at fault. The wall often is.
  • Failed silicone and sweep seals at the curb and wall channel. Water tracks under the glass, and by the time the leak is visible, the adjacent drywall or subfloor has been soaking for months. In San Francisco’s damp, fog-driven climate, that trapped moisture turns into rot faster than most homeowners expect.
  • Edge chips and spontaneous breakage from point-loading. Tempered glass is strong across its face and weak at the edge. Tight setting blocks, a missed metal-to-glass contact, or a curb that was never leveled puts a point load on the panel edge. One tap later and the whole panel lets go into the safety-glass crumble, which is exactly how tempered is supposed to fail, but it’s a failure anyway.
  • Mineral etching and hard-water haze. Abrasive cleaner, and occasionally a scouring pad on a stubborn soap film, scratch the glass surface permanently. Once it etches, no amount of polishing brings the clarity back. Replacement is the only real fix, and it’s avoidable.
  • Fogged or failed insulated glass units on rails and sliders. On Mr-Glass glass railing panels and insulated window units, a fogged or cloudy pane usually means the edge seal has failed and moisture is inside the unit. It’s a seal failure, not a cleaning problem, and the unit has to come out.

Mr-Glass Parts & Our Repair-vs-Replace Approach

OEM versus aftermarket for Mr-Glass enclosures isn’t a philosophy question, it’s a hole-spacing question. We specify OEM hinges, pivots, sweeps, seals, and handle hardware because the original panels were cut and drilled for those parts. An aftermarket hinge that sits even a millimeter off forces a re-drill, and a re-drilled tempered panel is a voided panel. A chipped, cracked, or dimensionally wrong panel is a replacement, full stop. Hinges, seals, sweeps, and rollers are usually a repair. Panels are not.

The honest answer sometimes points at re-templating rather than patching. If the wall isn’t plumb or the curb isn’t level, new hardware on a bad substrate just buys another few years before the same sag returns. We’d rather tell you that up front than sell you a hinge swap that doesn’t hold.

Parts are sourced and ordered per job, matched to your specific Mr-Glass model and panel dimensions. We don’t stock Mr-Glass parts locally. Call (866) 320-2646 and we’ll confirm what your enclosure takes.

Our Mr-Glass Service Process – Step by Step

  1. 1
    Diagnosis. We check plumb, level, and square on the wall, curb, and glass opening before touching hardware. On a sagging enclosure, this is where we learn whether the trouble is the pivot or the wall behind it. On insulated units, we confirm the seal is the culprit.
  2. 2
    Repair or install. OEM parts go on for hinge, pivot, and sweep work. For new installs, the panel is templated to the actual opening, setting blocks are set correctly, and the curb and wall channel are sealed with fresh silicone and a new sweep. When tile and a shower floor are part of the project, we lay the curb and pan so the shower drains toward the outlet before the glass goes back on.
  3. 3
    Test. We operate the door through its full swing, check clearances on the fixed panel and jamb, and run water to confirm the seals hold at the curb and wall channel.
  4. 4
    Warranty. Every project we handle is covered by the 730-Day Done Right Promise and a written scope up front. Upfront pricing, no surprises, and the number you see is the number you pay.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Mr-Glass Products We Service & Install in San Francisco

We cover the Mr-Glass line that San Francisco homes actually carry: frameless hinged and pivot shower enclosures in 3/8-inch and 1/2-inch tempered glass, Neo-Angle and corner-entry shower enclosures, mirrored sliding wardrobe and closet doors, glass railing and balustrade panels, and insulated glass units for windows and sliding doors. Alongside the glass work we handle walk-in shower installation and tile and flooring, since an enclosure is only as solid as the curb and pan beneath it.

San Francisco installation adds a wrinkle. On the west side of the city, fog belt and ocean salt corrode standard fasteners and hardware faster than inland specs assume. We spec stainless hardware and galvanized flashing on small jobs as well as large ones, because a shower hinge that rusts out in a few years is a repair call nobody wants to make twice.

We Also Service These Brands

Mr-Glass is a specialty line, and there’s plenty of other glass, tile, and cabinetry in a San Francisco home. We also work with KraftMaid, Cambria, Silestone, and Kohler on kitchen and bath projects. A single reputable contractor who can coordinate the glass, the tile, and the fixtures under one written scope beats three crews pointing at each other when something leaks.

FAQs – Mr-Glass Construction Service in San Francisco

Service Typical San Francisco Range
Frameless Glass Shower Enclosure / Walk-In Shower Installation $5,310 – $14,160
Shower Replacement $3,540 – $10,030
Tub-to-Shower Conversion $4,130 – $11,800
Bathroom Remodel $10,620 – $33,040
Bathroom Vanity Installation $945 – $3,540
Tile & Flooring (per project) $945 – $2,950

We offer 0% financing for 18 months and $1,000 off projects over $10,000. Call (866) 320-2646 for an exact quote. Estimates are free.

Book Your Mr-Glass Service in San Francisco, CA

Whether it’s a sagging frameless door, a leaking curb, or a fogged railing panel, Groundwork Construction Co. of San Francisco can route you to an independent local pro who knows the Mr-Glass line. Call (866) 320-2646 for a free estimate. Live person, 24/7. Upfront pricing, a written scope, and our 730-Day Done Right Promise on every project we handle.

Written by the team at Groundwork Construction Co. of San Francisco.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch