Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambria Windows & Doors: The San Francisco Owner’s Guide
Cambria-compatible window and door replacement in San Francisco typically runs $5,310 to $17,700 for standard window replacement and $9,440 to $29,500 for impact-rated installation, with most single-unit swaps finished in one visit. We’re an independent installer and service provider, not affiliated with Cambria, and we fit Cambria-compatible windows and doors with the 730-Day Done Right Promise behind the labor.
Owners usually find the failure the same way: a window that sticks in the Sunset fog, a door that won’t latch evenly in a Marina Victorian, or condensation trapped between the panes of a double-pane unit. One day it closes fine; the next there’s a draft you can feel on your knuckles. If that’s where you are, you already know it isn’t going to fix itself.
Key Takeaways
- Cambria-compatible window replacement in San Francisco: $5,310 – $17,700 installed.
- Impact-rated window installation: $9,440 – $29,500 installed.
- Most single-unit replacements finish in one visit.
- We answer the phone with a live person, 24/7.
- Every install is backed by the 730-Day Done Right Promise.
Which Cambria Models This Applies To
Cambria’s window and door lines break into two families you’ll meet in San Francisco homes: the coastal-climate aluminum and vinyl series built for salt air and wind-driven rain, and the impact-rated series that meets modern glazing standards for homes near the bay and outside the fire zones. The model tag lives on the jamb, usually a small sticker with a series code and a date stamp, or etched into the spacer bar between the panes on newer units. If the tag has faded, measure the rough opening instead: height, width, and frame depth in millimeters. Cambria’s part numbering keys off those dimensions plus the hardware series, so a door sourced for a 1¾-inch frame won’t seat properly in a 2-inch frame no matter how close the measurements look.
That’s the compatibility gotcha most owners trip on: Cambria sizing is nominal, not exact, so a “36-inch” window can measure anywhere from 35⅞ to 36¼ depending on series and year. If you order a replacement off the label alone without verifying the rough opening, you get a unit that doesn’t fit. We measure on site before we order, every time.
On OEM versus aftermarket: OEM Cambria hardware matches the original spec exactly, but lead times for a discontinued series can run weeks. A quality aftermarket equivalent from a reputable glazing manufacturer often installs sooner and holds its warranty just as well for standard thermal and weather-sealing needs. For impact-rated and coastal-series units, we stay with OEM-spec glass and hardware.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cambria Windows & Doors Is Failing
- Sticking or dragging sashes. Usually a warped frame or failed weatherstripping, common in Victorian-era San Francisco homes where the original rough opening has shifted with settling. If one corner drags and the opposite pulls wide, your frame has moved.
- Condensation between the panes. A failed seal let the argon escape. On a double-pane unit, once you see fog inside the glass, the seal is gone and only a full unit replacement fixes it.
- Drafts you can feel along the edges. Worn or compressed weatherstripping, or a frame that’s pulled away from the wall. In San Francisco’s windy neighborhoods, this shows up first as a whistle on gusty days.
- Doors that won’t latch evenly. Either the hinges have worn or the frame has racked. Hinge wear you can address; a racked frame points to foundation or rough-opening movement.
- Cracked or chipped glass, or a failing impact film. In impact-rated units, a delaminated film means the safety layer has degraded and the unit no longer provides the protection it was rated for.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Cambria-compatible window replacement in San Francisco runs $5,310 to $17,700 installed, and impact-rated window installation ranges from $9,440 to $29,500. The range is driven by unit size, glass spec (double-pane vs. impact-rated laminate), frame material, and how many units you’re replacing in one go. A single living-room window sits at the low end; a whole-floor impact-rated replacement sits at the top. Doors land in the upper part of the window-replacement range depending on width and hardware.
- Standard window replacement: $5,310 – $17,700 installed
- Impact window installation: $9,440 – $29,500 installed
- What’s in the number: the part, labor, removal and haul-away of the old unit, sealing, and primer
- What’s not: structural repair, drywall patching, or trim finishing beyond basic re-set
The price we quote is the price you pay – no change orders mid-job. Every install carries the 730-Day Done Right Promise, and our technicians are background-checked and uniformed.
DIY or Call Us?
There are three things an owner can safely check: the model tag on the jamb, the rough opening measurements, and whether a sash is dragging because of a hinge or because the frame has moved. That last one tells you a lot before anyone shows up. Where DIY goes wrong is swapping the unit itself. A double-pane window is heavy, awkward, and fragile; dropping it on a San Francisco balcony or pinching a finger between glass and frame is a real risk, and a misaligned install leaks within a season. There’s also a code piece: San Francisco requires permits for window replacement in many cases, and the inspection needs to pass. We pull the permit and pass the inspection as part of the job. Our technicians have up to 12 years of experience.
Call (866) 320-2646 to schedule a free estimate – a live person answers any hour, any day. From foundation to finish line, we handle the part, the permit, and the install.
FAQs
A well-installed Cambria-compatible window lasts 15 to 25 years in San Francisco’s coastal climate; the seal on a double-pane unit typically gives out at 10 to 15 years in fog-belt neighborhoods like the Sunset and Richmond, where constant moisture stresses the spacer. Doors last longer if the hardware is maintained. Call (866) 320-2646 for an exact quote – estimates are free.
Sometimes. A dragging sash from worn weatherstripping or a hinge issue is repairable; a fogged double-pane unit is not – once the seal fails, the whole unit needs swapping. We’ll tell you which one you’re dealing with before we quote. Call (866) 320-2646 to schedule.
Most single-unit replacements finish in one visit, usually under a day for a standard window. Impact-rated units or doors with frame repair can stretch to two visits. We schedule around your day. Call (866) 320-2646 for a schedule estimate.
We verify the model tag and measure the rough opening on site before ordering, then match the unit to the Cambria series and hardware spec. When an OEM part is back-ordered or discontinued, we source a quality aftermarket equivalent where it meets the same thermal and weather-sealing standards. No parts are carried on a truck – every unit is ordered to your exact opening. Call (866) 320-2646 to start.
We also service KraftMaid, Silestone, and Kohler installations across San Francisco, so the same crew can handle adjacent kitchen and bath work under one project quote. Cambria, KraftMaid, Kohler, and the rest of our brand partners let you choose quality, not just availability.
Upfront pricing, no surprises, and a live person on the line at (866) 320-2646 whenever you’re ready.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.