Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling: The San Francisco Owner’s Guide
Schluter kitchen remodeling in San Francisco typically runs $16,520 – $53,100 installed, depending on kitchen size, tile scope and whether we’re correcting a failed substrate. We work with Schluter products as an independent contractor, including KERDI waterproofing, DITRA uncoupling membranes and the SCHIENE and JOLLY trim profiles that finish tile edges. That range holds whether you’re rebuilding one failed tile field or starting a full kitchen.
Most San Francisco owners discover the problem through cracked grout lines or a hollow thud underfoot long before they know a Schluter part is behind it. In older Inner Sunset and Richmond District homes, we see it after a slow leak has already softened the subfloor under the membrane. A popping tile near the dishwasher usually means the waterproofing gave out first, not the tile.
Which Schluter Models This Applies To
Schluter’s kitchen lineup isn’t one product; it’s a system, and getting the right piece means matching the profile to the job. The most common under-tile layers are DITRA (uncoupling membrane), DITRA-HEAT (membrane with heating cable), and KERDI or KERDI-BOARD for waterproofing. Edge trim comes in the SCHIENE, JOLLY, QUADEC and RONDEC families, sized by tile thickness, usually in millimeters. A 3/8-inch tile calls for a different profile than a 1/2-inch one, and using the wrong size is the single most common failure we’re called to fix.
Identifying your part: measure your tile thickness with a caliper, then check the profile’s printed size on the cardboard sleeve or the stamped impression on the trim itself. Older installations may carry discontinued SKUs or imperial sizes that Schluter has since shifted to metric. That’s where the OEM-versus-aftermarket decision matters. For waterproofing and uncoupling membranes, use genuine Schluter – the fleece backing and grid construction are what carry the warranty, and copycat membranes don’t match it. For edge trim, a quality anodized aluminum or stainless equivalent from a brand like Schluter or a certified alternative will hold up, but verify the exact millimeter size against your tile.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling Is Failing
- Hollow-sounding tile across a wide area. DITRA has debonded from the subfloor, which usually traces back to a thinset mixed too dry or a slab that wasn’t prepped. Tap lightly with a plastic tool handle; a dull, drummy sound means the layer has separated.
- Grout cracking in a straight line or grid pattern. That’s movement transferring through the tile because the uncoupling membrane isn’t doing its job. In San Francisco’s settled 1940s stucco-and-slab homes, this pattern tracks with foundation movement the membrane was meant to absorb.
- Water staining or a musty smell at a seam. KERDI banding wasn’t overlapped correctly at a penetrations point, or the sealant failed at a corner. Look at the seams around the sink, dishwasher, and floor-to-wall transitions first.
- A raised or curled edge at SCHIENE or JOLLY trim. The trim was sized for a thinner tile and someone pushed it, or the mortar behind it dried before it set. This shows up as sharp edges catching a cloth or a bare foot.
- Loose transition where tile meets a cabinet or island. Movement at the joint from a missing or compressed backer rod under the profile. It’s cosmetic at first, then it lets water in.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Replacing a failed Schluter kitchen layer in San Francisco falls within our $16,520 – $53,100 installed kitchen remodel range; if the job is scoped to a smaller tile field it lands closer to the small-kitchen figure of $10,620 – $23,600. Backsplash-only work runs $945 – $2,950; a kitchen island install is $3,540 – $11,800. Tile repair around a failed trim or a small membrane swap is part of a broader remodel quote, not a standalone line.
What drives the range: the square footage, whether the old membrane must be ground out or can be oversealed, whether the subfloor needs leveling, and whether DITRA-HEAT is going in. Our quotes are line-item and fixed. The number you see is the number you pay, no change orders for the prep work that surfaces mid-job. Every Schluter install carries our 730-Day Done Right Promise – if the membrane, trim or tile fails within that window due to workmanship, we make it right.
DIY or Call Us?
You can safely check some things yourself: tap the tile for hollow spots, look at the seams around the sink and dishwasher, measure tile thickness to confirm the profile size. That’s diagnostic, not repair.
Where DIY goes wrong: Schluter systems depend on thinset consistency, membrane overlap tolerance, and drying time that a weekend tile set doesn’t respect. A homeowner who reseals a KERDI corner over a wet substrate traps moisture and grows mold; a homeowner who re-trims a SCHIENE edge with construction adhesive leaves a profile that curls within a season. The failure compounds, and the repair gets more expensive. For finished tile and waterproofing work, call a trained installer. Call (866) 320-2646 and we’ll tell you what we’re seeing from the photos and the symptoms.
FAQs
Properly installed Schluter waterproofing and uncoupling layers routinely last 20 to 30 years, but lifespan in San Francisco depends heavily on prep and moisture control. Foggy west-side neighborhoods like the Sunset and Richmond test sealants harder than dry inland air. Call (866) 320-2646 for a no-cost assessment of what’s likely to hold up in your home.
Sometimes yes. A single failed trim profile or a localized KERDI seam can be repaired without ripping the whole field; a debonded DITRA membrane covering most of the floor usually can’t. The honest split is whether the failure is isolated or systemic. Our techs will tell you which one you’re facing before any demolition starts.
Most localized repairs and small remodels run one to three weeks from demo to final seal coat, depending on tile layout, drying time and whether cabinets are moving. Full kitchen remodels run longer. We schedule to a written timeline and hold to it.
We source genuine Schluter components from authorized distribution and verify the exact profile or membrane specification against your tile thickness before ordering. We don’t carry parts on a truck, and we don’t stock Schluter in a warehouse – each job gets the correctly sized part. We also work in KraftMaid, Cambria and Silestone when the scope reaches cabinets and counters.
No. We’re an independent construction company that installs Schluter products; we’re not affiliated with, endorsed by, or sponsored by Schluter-Systems.
From foundation to finish line, our team brings up to 12 years of technician experience to every Schluter project. Calls are answered by a live person 24/7. Every job is background-checked, uniformed and backed by our 730-Day Done Right Promise. We’re proud to serve San Francisco communities today, and our pricing is upfront with no surprises: 0% financing for 18 months plus $1,000 off projects over $10,000. Call (866) 320-2646 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.