Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The San Francisco Owner’s Guide
Groundwork Construction Co. of San Francisco installs Schluter waterproofing and uncoupling systems (DITRA, KERDI, KERDI-BOARD, DITRA-HEAT) as part of full home additions and ADU builds, and the installed cost of an addition runs $53,100 – $153,400, with ADU construction at $106,200 – $259,600. Additions are planned work, so we schedule them properly rather than promising same-day starts. Owners usually discover a Schluter failure the same way: a grout line in the new bathroom cracks, a tile sounds hollow when tapped, or a soft spot and musty smell show up at the shower curb months after the tile went down.
Which Schluter Models This Applies To
Schluter systems show up across a San Francisco addition in a few predictable places: DITRA over plywood subfloor in the new bath and laundry, KERDI or KERDI-BOARD in the shower and wet areas, DITRA-HEAT where the homeowner wanted warm floors, and KERDI-BAND and KERDI-FIX at seams, corners, and penetrations. Getting the right part means matching the family first, then the format. DITRA comes in rolls and sheets in different sizes; KERDI-BOARD comes in several thicknesses (you pick by wall buildup, not by habit); DITRA-HEAT membrane and its heating cable are separate pieces that have to be ordered to the same system.
The identification gotcha most owners miss: the printed label lives on the roll core or the carton band, and once the carton is gone you’re measuring membrane thickness and stud spacing to confirm what’s actually installed. Schluter’s published installation handbooks and the printed specs on the membrane itself are the authority here, and we check those before ordering anything. On the OEM-versus-aftermarket question, this is a category where the generic substitute is a real gamble – a no-name uncoupling mat may not carry the same waterproofing and sheer-bond test data as the Schluter system, and mixing brands inside one shower assembly voids the very warranty you’re paying for. We install with genuine Schluter components for that reason. We’re an independent installer and not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Hollow tile and cracked grout lines. That drum-like sound means the thinset didn’t bond to the membrane or the membrane to the subfloor, often from a skimped or contaminated layer during the addition.
- A soft or spongy floor at a doorway or transition. Water got past the waterproofing where the DITRA met a different floor covering, and the plywood underneath is now swollen.
- Musty odor or a damp shower curb. KERDI seams and corners that weren’t banded correctly let moisture into the assembly, and it has nowhere to go but into the framing.
- Loose tile around the drain or at floor-to-wall joints. Movement at the most vulnerable point of the wet area means the uncoupling layer is doing its job unevenly or wasn’t installed to the perimeter.
- DITRA-HEAT that heats unevenly or not at all. A cable nicked during tile-setting or a thermostat wired without the sensor in the right spot is the usual culprit, and cracked tile over the fault traces the path.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For the full scope this page covers, home additions in San Francisco run $53,100 – $153,400 and ADU construction runs $106,200 – $259,600; garage conversions land at $35,400 – $94,400. A targeted wet-area rebuild (one shower or bathroom floor re-waterproofed and re-tiled) sits inside our bathroom remodel range of $10,620 – $33,040, and a walk-in shower rebuild runs $5,310 – $14,160. What drives the spread is how much of the assembly comes out, whether the subfloor or framing is wet, tile size and material, and whether a heating system is being replaced. We quote parts and labor as separate line items with upfront pricing, so the number you see is the number you pay. Every addition and rebuild is backed in writing by the 730-Day Done Right Promise.
DIY or Call Us?
Some checking is safe. You can tap tile for hollow spots, look for efflorescence or a dark line along the shower curb, confirm the floor heat thermostat is getting power, and photograph every label before the carton leaves the site. What you shouldn’t do is pull up a bonded Schluter assembly yourself on the guess that one tile is the problem – the waterproofing is a continuous system, and cutting into it to chase a soft spot often turns a small patch into a full rebuild, and the demolition is where most of the damage to adjacent work happens. This isn’t a spring or an electrical panel, so there’s no imminent danger, but a wet assembly hidden under tile can rot framing for a year before you feel it. Call us at (866) 320-2646 for a free estimate and we’ll tell you honestly whether this is a patch or a rebuild.
FAQs
A properly installed Schluter assembly should outlast the tile itself, commonly 20 to 30 years or more. Our fog and marine moisture mean venting and waterproofing detail matter as much as the product, and most failures we see trace back to installation detail rather than the material. Call (866) 320-2646 to have a failing assembly looked at before it spreads – estimates are free.
Sometimes, yes – a single nicked DITRA-HEAT cable or one failed KERDI corner can often be repaired in place. Once water has reached the subfloor or framing, though, a partial patch just hides the problem, and we’ll tell you which one you’re looking at after we open it up. Call (866) 320-2646 for an honest assessment – the estimate costs nothing.
A targeted wet-area rebuild usually runs one to two weeks once materials arrive; a full addition with new tile, waterproofing, and heat runs weeks, not days. We give you a written schedule up front and stick to it, with no change orders sprung on you mid-job. Call (866) 320-2646 and we’ll scope the timeline for your project.
We source from authorized Schluter distributors and verify the system family and format against your installation before ordering. We don’t carry stock on a truck and won’t substitute a generic mat for a genuine Schluter component, because it can void the warranty you paid for. Call (866) 320-2646 and we’ll confirm exactly which parts your project needs.
Ready to price your addition or ADU? For homeowners who refuse to gamble on their biggest investment, Groundwork Construction Co. of San Francisco brings a curated slate of brands across every trade – Schluter for tile and waterproofing, KraftMaid and Cambria and Silestone for the finishes inside – so you choose quality, not just availability. Calls are answered by a live person 24/7, our background-checked, uniformed technicians show up ready to work, and you get 0% financing for 18 months plus $1,000 off projects over $10,000. Call (866) 320-2646 to schedule your free estimate and design consult.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.