A Groundwork company - serving San Francisco, CA

Boral Driveway & Pavers in San Francisco, CA

Driveway & paversDriveway & pavers
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Boral Driveway & Pavers: The San Francisco Owner’s Guide

We install Boral-compatible driveway and paver systems across San Francisco, and a full paver driveway typically runs $8,260 – $21,240 installed, while a paver patio lands at $4,130 – $12,980. Boral’s clay and concrete paver lines are the ones we see most on hillside properties here, and we can usually schedule an assessment within the same week, with most single-run installations completed in one visit. If you’re searching for a specific paver or edge restraint, our technicians have up to 12 years of experience matching the right product to your existing run. We’re an independent service provider and not affiliated with Boral.

Call (866) 320-2646

Owners usually discover a failed paver system after a heavy rain, not before. You walk out to the driveway and see a low spot holding water, or a line of pavers that has started to ride up along the garage apron. Sometimes it’s quieter than that: a hairline crack that spreads a little each season, or sand washing out of the joints so fast that re-sanding becomes a monthly chore. In San Francisco, the clues tend to show up on the west-facing slopes first, where fog drip and wind-driven rain hit hardest.

Key Takeaways

  • Boral paver driveways run $8,260 – $21,240 installed in San Francisco; paver patios run $4,130 – $12,980.
  • Most failures trace back to base preparation and drainage, not the paver itself.
  • A single paver swap is straightforward; a full re-set is where DIY goes wrong.
  • All work is backed by our 730-Day Done Right Promise.

Which Boral Models This Applies To

Boral’s residential line includes clay pavers under names like Boral Clay Pavers, Boral Stone concrete pavers, and the Boral Masonry retaining and wall block systems. Each line has its own nominal dimensions, and this is where owners get tripped up: a 2 ¾-inch-thick paver from one Boral series may not match the thickness of an older run, and when thicknesses don’t match, the joint sand migrates out of the thinner joints first. If you can’t find the label on the back of a paver, measure the length, width, and thickness of one intact unit and compare it against your local supplier’s spec sheet before you order anything.

The OEM-versus-aftermarket call matters here. If your goal is to match an existing Boral run exactly, an OEM Boral paver is usually the only way to hit the same color-and-texture batch. If you’re repairing a hidden edge course or a section that will be covered by landscaping, a quality aftermarket match is often good enough and cheaper. For visible runs on a San Francisco sloped driveway, we lean toward the OEM match because color batches vary noticeably between production runs and a partial repair in a mismatched batch can read as a patch from the sidewalk.

If your project also touches countertops or kitchen surfaces, we carry the same brand-partner approach with KraftMaid, Cambria, and Silestone.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Boral Driveway & Pavers Is Failing

Paver failure almost never starts at the paver. It starts underneath. Here’s what failed systems look like in San Francisco, and the cause behind each one:

  • Ponding water after a storm. A low spot in the pavement means the base wasn’t compacted evenly or the drainage slope was lost during installation. Standing water is the fastest way to lose joint sand, and once sand is gone, pavers shift.
  • Pavers riding up along an edge. Usually a failed edge restraint. The plastic or concrete edging that holds the field in place has cracked or pulled loose, and every paver behind it starts to creep with each rain.
  • Joint sand washing out within one season. Either the wrong sand was used (polymeric vs. regular mason sand) or the drainage is sending water across the joints instead of away from them. In San Francisco, fog drip alone can accelerate this on shaded north-facing runs.
  • Hairline cracks spreading on individual pavers. A single cracked paver is fine. Multiple cracks in the same run point to base deflection or a paver that was set too thin under vehicle load.
  • Ruts and depressions in the wheel path. On sloped City driveways this usually means the sub-base wasn’t deep enough for the load it’s carrying, and the aggregate has begun to move.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Paver driveway installation in San Francisco runs $8,260 – $21,240 installed. Paver patio installation runs $4,130 – $12,980. If you’re weighing options, a concrete driveway runs $5,310 – $14,160, asphalt paving runs $4,130 – $10,620, and a full driveway replacement runs $5,900 – $16,520.

Three things drive where you land in that range: the square footage and how much of it is on a slope, whether the existing base has to come out, and the Boral series and color batch. Hilly terrain here means more excavation and more edge restraint than a flat lot, and that shows up in labor. Our quotes are line-item and upfront, so you see the paver cost, base cost, and drainage cost separately. If your project is over $10,000, we take $1,000 off, and 0% financing for 18 months is available on the balance. Every installation carries our 730-Day Done Right Promise.

DIY or Call Us?

Owners can safely do a few things. Rake a fresh pass of joint sand into the joints. Clear leaf litter and debris from the drain grates and the low edge of the driveway. Take a level reading or a photo of where the water pools, and note the date. Those observations help us quote accurately and cost you nothing.

Here’s where DIY goes sideways. A single-paver swap is doable if the base under it is intact. But the moment you pull more than a couple of pavers, you’re opening up a base that hasn’t been touched since installation, and the failure you saw on the surface almost always started underneath. Re-setting pavers without re-compacting the base and re-establishing the drainage slope just puts the same problem back in place, and in San Francisco’s wet season, that means you see the same cracking by the next spring. If the paver run is on a retaining wall or a slope above a structure, we strongly recommend against opening it up yourself. Call us at (866) 320-2646 and we’ll tell you honestly whether it’s a repair or a re-set.

FAQs

How long do Boral pavers last in San Francisco? A properly installed Boral clay or concrete paver driveway in San Francisco typically lasts 25 – 30 years, and often longer for clay pavers that don’t take on water. The paver itself usually outlasts the joint sand and edge restraint by a lot, and those are the parts that fail first.

Can it be repaired instead of fully replaced? Often, yes. A localized failure with intact base material is a repair. If the base is deflecting or the drainage slope has been lost, the repair is usually short-lived, and the smarter spend is a full re-set. Call us at (866) 320-2646 and we’ll assess before you spend.

How long does a paver swap or repair take? A single-paver repair is often done in one visit. A partial re-set with drainage corrections runs a few days depending on weather. We answer the phone 24/7 with a live person, so you can call and get a real timeline, not a voicemail.

How do you source the Boral paver for my job? We order Boral products through Boral’s authorized distribution and match the color batch to your existing run where the repair is visible. If the exact series isn’t available in the right batch, we’ll tell you upfront rather than install a mismatched paver and call it a day.

If your Boral driveway or paver system is showing any of the signs above, the smart move is a free estimate before the next rain season. Call Groundwork Construction Co. of San Francisco at (866) 320-2646 to schedule your free estimate and design consult. Our quotes are upfront and line-item, all work is backed by the 730-Day Done Right Promise, and our technicians are background-checked and arrive in uniform. Calls are answered by a live person, 24/7.

Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch