A Groundwork company - serving San Francisco, CA

Boral Home Additions & ADU in San Francisco, CA

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Boral Home Additions & ADU: The San Francisco Owner’s Guide

We install Boral-spec additions and ADUs across San Francisco, and most whole-project work here lands between $53,100 and $153,400 for a home addition, with ADU construction running $106,200 to $259,600. An ADU isn’t a part you swap in a morning, so “same-day” doesn’t apply to the build itself. What owners usually discover first is a failed component inside an existing Boral-clad addition: a cracked trim board, a delaminated sill, a hairline at a panel joint that keeps coming back. Those symptoms are how this page starts, because that’s what sends most people searching for a Boral answer in San Francisco.

Call (866) 320-2646

Which Boral Models This Applies To

Boral makes material, not branded house lines, so “which model” really means which Boral product family your addition was built with. Their exterior and trim lines (the fiber-cement and composite cladding used on Bay Area additions) carry profile names and printed stamps on the back or edge of each board. Find one: pull the manufacturer label off an offcut, or read the stamp on a rake board you can reach from a ladder. That stamp, plus a caliper measurement of thickness, tells us the exact profile and lets us match a replacement without guessing. This matters because Boral’s fiber-cement and composite trims are not interchangeable; a board cut for one series won’t take the same fasteners or finish schedule as another, and putting the wrong one on a San Francisco addition over the foggy western neighborhoods invites premature failure.

The OEM-versus-aftermarket call is genuinely yours to make. OEM Boral replacements match profile, color batch and warranty terms exactly, which is what you want when only part of a wall is being repaired and it needs to look like it was always there. Quality aftermarket equivalents can cost less and perform fine on full-face replacements where nothing abuts. We’re an independent provider and not affiliated with Boral, so we quote both paths with the tradeoffs in writing and let you choose. For interior finishes on an ADU, we also work with KraftMaid, Cambria and Silestone.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Boral Home Additions & ADU Is Failing

  • Chalking or powder on the surface. Fiber-cement and composite cladding shed a fine dust as the finish breaks down, often faster on south- and west-facing walls where UV and salt air hit hardest. It usually means the factory finish is past its service life.
  • Cracks at board ends and joints. Small movement cracks open where boards were butted too tight with no gap for thermal swing. Left alone, water tracks in behind the board.
  • Soft or delaminated edges. Trim that feels spongy near the bottom edge has taken on moisture, common on San Francisco additions close to the coast where fog keeps walls wet longer.
  • Paint peeling in sheets, not flakes. Delamination like this points to a finish applied over a damp or chalky surface, so the coating never bonded.
  • Visible fastener rust trails. Streaks below nails or screws mean incompatible fasteners or failed sealant, and they telegraph where the wall is taking water.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For the material-and-labor work on a Boral-clad addition, installed pricing in San Francisco runs $53,100 to $153,400 for a home addition and $106,200 to $259,600 for a full ADU build, with garage conversions at $35,400 to $94,400. What drives the range is scope: square footage, how much existing cladding gets replaced versus matched, site access on tight city lots, and whether the work touches structural framing. We quote line-item, parts and labor separately, so you see exactly what the Boral material costs versus the install. The number you see is the number you pay, and all of it is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right.

DIY or Call Us?

You can safely check the basics: read the board stamp, measure thickness, note where cracks and rust trails appear, and photograph everything for a quote. Where DIY goes wrong is at the wall itself. Replacing cladding on an addition means working at height and opening the weather barrier, and a mis-flashed joint on a San Francisco wall will leak quietly for a season before you see it inside. Add that ADU and addition work touches structural framing and permits, and this stops being a homeowner job. Get the diagnosis right the first time. Call (866) 320-2646 and we’ll tell you whether it’s a repair or a rebuild.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch