A Groundwork company - serving San Francisco, CA

PGT Roofing in San Francisco, CA

RoofingRoofing
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

PGT Roofing: The San Francisco Owner’s Guide

We install and repair PGT-compatible roofing systems across San Francisco, and most residential roof work here runs $9,440 to $23,600 for a full replacement, with targeted repairs at $470 to $2,125. PGT is best known for hurricane-rated windows and doors, and when a PGT product shows up on a San Francisco roof assembly – typically a skylight, roof window, or the flashing collar around a vented unit – the failure almost always starts at the seal, not the glass. Owners usually find out the same way: a brown ring spreading on the ceiling after the first real rain of the season, or a whistle on the west side of the house when the afternoon wind comes off the ocean.

Call (866) 320-2646

We’re an independent service provider. Groundwork Construction Co. of San Francisco is not affiliated with PGT, and we don’t claim to be. What we do is source the right compatible component, install it correctly for this climate, and back the work with our 730-Day Done Right Promise.

Key Takeaways

  • PGT roof-mounted units usually fail at the seal or flashing, not the frame or glass.
  • Installed cost in San Francisco runs $470 to $2,125 for repair work and $9,440 to $23,600 for a full replacement.
  • Salt air and marine fog accelerate sealant and gasket breakdown faster here than inland.
  • Our technicians have up to 12 years of experience with roof-mounted units and flashing.
  • We pull permits where required and leave you with a written, itemized quote before any work starts.

Which PGT Models This Applies To

PGT makes a wide catalog, and the roof-relevant pieces are the ones rated for exterior, weather-facing installation. The lines you’ll most often see on a San Francisco home are the WinGuard impact-rated series and the Estate Collection units – these show up as fixed skylights, vented roof windows, and occasionally as an impact-rated unit set into a low-slope roof over a stairwell or rear addition. The first thing we do on any call is find the identification label. On PGT units it’s usually etched into the glass corner or printed on the frame, and it carries a model number and a glass spec code. That code matters: a unit stamped for impact glazing has a different frame depth and gasket profile than a standard unit of the same nominal size, and a generic flashing kit won’t seat right.

Measure the rough opening, not the visible glass. A 2-inch difference in frame depth changes which curb and flashing detail you need, and on a flat or low-slope San Francisco roof that difference is the gap where water gets in. For aftermarket parts, the decision comes down to this: OEM gaskets and flashing collars match the original profile exactly, while quality aftermarket equivalents can work when the dimensions and material grade line up. We compare both on every job and tell you which one actually fits your unit rather than which one is cheaper to source. We also handle KraftMaid, Cambria, and Silestone on the interior side, so if a failed roof unit has stained a ceiling or a kitchen below it, that conversation happens with one contractor instead of three.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your PGT Roofing Is Failing

Here’s what a failing roof-mounted PGT unit actually looks like, and what’s happening underneath each symptom.

  • Water staining on the ceiling below. The flashing collar or the sealant bead around the frame has cracked. Once the bead loses adhesion, water tracks along the frame and shows up inside within one or two storms.
  • Draft or whistling at the frame edge. The perimeter gasket has compressed or shrunk. PGT frames are rigid, so the leak is usually at the seal line, not the glazing itself.
  • Fogging between the panes. The insulated glass unit’s seal has failed and moisture has entered the cavity. This one can’t be re-sealed in place; the glass unit gets replaced or the assembly does.
  • Visible cracking or crumbling at the sealant line. San Francisco’s salt air and marine fog break down standard sealants faster than inland sun does. If the bead looks chalky or has pulled away, it’s already letting water past.
  • Condensation on the interior face that won’t clear. Often a sign the thermal seal is compromised, or that the unit was installed without the correct back-ventilation detail for a low-slope roof.

Two things we see repeatedly in San Francisco: units on the ocean-facing slope of a home fail years earlier than the same unit on the sheltered side, and low-slope roof penetrations near a parapet collect debris that holds moisture against the flashing. Neither is a defect in the PGT product. Both are installation and maintenance realities specific to this city.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Roof repair in San Francisco runs $470 to $2,125 installed when we’re resealing, re-flashing, or swapping a single component. A full roof replacement, which is the right call when the decking around the penetration has rotted or the roof is at the end of its life, runs $9,440 to $23,600. Metal roof work sits higher at $17,700 to $47,200, and tile roof repair – common on older San Francisco homes – lands at $710 to $2,950.

What moves the number: whether the glass unit is intact (reseal only) or failed (unit replacement), how much decking needs replacing once we open it up, roof pitch and access, and whether the existing curb and flashing detail can be reused. You get a written, itemized quote that separates parts from labor, so you can see exactly what you’re paying for. The number you see is the number you pay – no change orders on the signed scope. And the work carries our 730-Day Done Right Promise: if it’s not done right, we make it right. We pull permits where San Francisco requires them and pass the inspections.

DIY or Call Us?

Roof work at height is the honest dividing line here. If you can safely reach the unit from inside or from a stable, ground-level vantage point, you can check for staining, look at the sealant bead, and note the model code from the label. That information helps when you call. What you shouldn’t do is climb a pitched roof, cut into flashing, or try to reset a glazed unit yourself – a fall from a San Francisco roof is a serious injury, and a bad flashing repair just moves the leak somewhere you can’t see until the damage is larger.

If you’re seeing active water intrusion, call us at (866) 320-2646 – a live person answers, 24/7. We’ll tell you on that call whether it’s a reseal or a replacement, and schedule a free estimate. Our technicians are background-checked, arrive in uniform, and have up to 12 years of experience.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch