Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Ameristar Kitchen Remodeling: The San Francisco Owner’s Guide
Ameristar-compatible kitchen remodeling in San Francisco typically runs $16,520 to $53,100 installed, depending on cabinet footprint, counter surface, and whether you’re reworking the layout or replacing surfaces in place. Small kitchen overhauls land lower, in the $10,620 to $23,600 band. We install and finish these kitchens, and most single-trade swap-outs (a failed cabinet run, a cracked counter section, a backsplash replacement) are completed in a single visit once parts are matched and on site.
San Francisco owners usually discover the problem in stages. The soft-close door that quit cushioning sometime last month. The under-cabinet light that flickers when the fridge kicks on. The counter seam near the sink that’s gone dark and gritty. A drawer box that no longer pulls square because its runner has worn past tolerance. By the time you’re searching for Ameristar-specific answers, you’ve already ruled out “it’s just loose” and you want a part number, an honest price, and someone who knows these kitchens.
Key Takeaways
- Installed Ameristar-compatible kitchen work in San Francisco: $16,520 to $53,100.
- We are an independent service provider, not affiliated with Ameristar.
- Failures cluster around hinges, drawer runners, and caulk lines, not the cabinet box itself.
- All work backed by our 730-Day Done Right Promise.
Which Ameristar Models This Applies To
Ameristar builds semi-custom and stock cabinet lines sold through big-box and dealer channels, and the part you need hinges on three things: the cabinet series, the door style, and the hardware vintage. Most Ameristar doors mount on concealed European-style hinges (35mm cup bore is the common standard), and drawer boxes run on either side-mount epoxy slides or full-extension ball-bearing runners depending on series and year. The gotcha: the same door style can ship with different hinge brands across production runs, so the stamp on your existing hinge plate matters more than the door name.
Identifying your part takes ten minutes. Open the door and read the hinge cup: brand name and model code are usually stamped there. For drawer slides, pull the box out and check the runner body for a manufacturer and length marking. Measure the cabinet opening height and width to the nearest 1/16 inch; Ameristar face-frame openings commonly run 1/8 to 1/4 inch smaller than the box. Photograph the label inside the door or on the cabinet back panel – many Ameristar units carry a series sticker there.
On the OEM-versus-aftermarket question: for hinges and slides, a quality aftermarket equivalent (Blum, Grass, or comparable) often outlasts the original and costs meaningfully less. For doors and drawer faces with a specific stain or foil finish, OEM matching is usually the only realistic route, and colors can shift between production years, which is why we recommend replacing in full sets rather than one door at a time. We don’t stock parts and we don’t carry inventory on a truck; we source what’s needed for the job after we’ve confirmed the match. Our technicians have up to 12 years of experience with kitchen cabinetry fitting. If you’re comparing finishes, we also work with KraftMaid, Cambria, and Silestone for full-remodel scopes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Ameristar Kitchen Remodeling Is Failing
These kitchens fail in predictable places. Here’s what each symptom usually points to:
- Doors that won’t stay closed or drift open. The hinge’s internal spring or friction cam has worn. On concealed hinges, once the tension mechanism gives out, adjusting screws only buy time – the hinge body needs replacing.
- Drawers pulling rough or sticking mid-travel. Worn ball bearings or a bent slide rail. In San Francisco’s damp neighborhoods (think the fog belt in the Sunset or Richmond), metal slides corrode faster than in dry inland climates, accelerating the failure.
- Soft-close no longer cushioning. The damper cartridge inside the hinge is spent. This is the single most common Ameristar failure we see, and it’s rarely just one hinge – dampers from the same production run tend to age in parallel.
- Countertop seams darkening or lifting. Failed caulk or adhesive at the joint. Left alone, moisture wicks under laminate or stone edges and softens the substrate.
- Backsplash tiles or panels loosening. Adhesive failure behind the tile or a shifting wall. Common in older San Francisco homes where the wall behind the splash isn’t perfectly flat.
Replacement Cost & What’s Included
Installed pricing in San Francisco, using our standard ranges:
| Scope | Installed Range |
|---|---|
| Cabinet installation (full run) | $4,720 – $15,340 |
| Countertop installation | $2,360 – $7,670 |
| Backsplash installation | $945 – $2,950 |
| Kitchen island installation | $3,540 – $11,800 |
| Small kitchen remodel (whole-room) | $10,620 – $23,600 |
| Full kitchen remodel | $16,520 – $53,100 |
What drives the range: cabinet count and door style (a full face-frame replacement runs higher than a hinge-and-slide refresh), counter material (quartz and stone push toward the top end, laminate toward the bottom), and layout – moving plumbing or electrical always adds labor. Our pricing is upfront and itemized, so you see parts and labor as separate lines before we start. The number you see is the number you pay. All work is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in the residential construction space. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some of this is safely within reach for a careful owner. Replacing a single hinge or a drawer slide matches the original is a genuine one-hour job with a screwdriver and the right part number. Re-caulking a counter seam you do yourself with an hour and a tube of silicone. Tightening loose cabinet-to-wall screws, adjusting door alignment with the hinge screws – all fine.
Where it goes wrong: replacing stone or laminate countertops wrong can crack a slab or damage the sink cutout; re-tiling a backsplash over an uneven wall without addressing the substrate fails within a season; and pulling a cabinet run to fix one failing box often means re-anchoring to studs and re-leveling the whole run, which is where the finish and alignment go sideways. If your failure is in the counter or backsplash, call us. If it’s a single hinge or slide, read the model stamp first and call with it – we’ll confirm the match and give you an honest answer on what the swap costs installed. Live person, 24/7, at (866) 320-2646.
FAQs
How long should Ameristar cabinet hinges and slides last in San Francisco? Quality concealed hinges typically run 10 to 15 years; drawer slides 8 to 12 years under daily kitchen use. In San Francisco’s fog belt, salt air and indoor humidity can shorten metal slide life, so expect the lower end near the coast and the higher end inland.
Can a failing Ameristar hinge or slide be repaired instead of replaced? Sometimes – a hinge can be re-tightened or a screw hole filled and re-drilled, but if the damper or spring is gone, it needs replacement. Slides with a bent rail can occasionally be straightened, though new slides are usually the more reliable call. Call (866) 320-2646 and we’ll tell you honestly which side of that line you’re on.
How long does the swap take? A single-hinge or single-slide replacement is typically done in a single visit, often under an hour. A full cabinet-run replacement is a day, countertops typically a day once they’re cut and on site, and a whole-kitchen scope runs several days to a couple of weeks depending on layout changes. Exact timeline confirmed in your free estimate.
How do you source the Ameristar part? We match your model stamp and measurements to the correct OEM part or an equivalent aftermarket, then order it after we’ve confirmed fit. We don’t stock parts and we don’t carry inventory on a truck – that keeps us honest about what we can and can’t source, and it’s why we need the model label photo before we commit to a part.
Get an Exact Price for Your San Francisco Kitchen
Ameristar kitchen work in San Francisco is priced on parts and labor separately, with upfront pricing and no surprises. Call (866) 320-2646 to schedule your free estimate and design consult – a live person answers 24/7, no voicemail. From foundation to finish line, backed in writing by our 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.