Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The San Francisco Owner’s Guide
Jerith fence installation in San Francisco typically runs $4,130 to $10,620 installed, and we usually schedule the walkthrough and quote within a few business days of your call. The job moves fast once we’re on site because aluminum ornamental fence sections are modular; most installs finish in a single visit.
Owners rarely come to this page for a fresh install. They come because a painted aluminum picket is leaning after a wind gust off Twin Peaks, a post foot has rusted through in the salt air near Ocean Beach, or a gate hinge has finally sheared after years of use. You noticed the wobble, then the noise, then the gate that won’t latch. That’s the moment this page is for. We match the part to your Jerith line, quote the whole install in writing, and back the workmanship with our 730-Day Done Right Promise.
Which Jerith Models This Applies To
Jerith ornamental aluminum fencing has been made in several residential lines over the years, and the fittings are not interchangeable across them. The most common residential series are the standard 54-inch picket lines and the taller estate-height runs, and the gate hardware, post caps, and picket spacing differ between them. Before we order anything, we measure the actual picket width, the rail height, and the post wall thickness on your fence, because a part ordered off a photo alone is the number one cause of a return-and-reorder delay.
The identifying marks live in two places. Check the inside face of a gate frame or the underside of a top rail for a stamped or printed model code; if the fence was installed by a prior owner, the original paperwork may be long gone. Where there’s no code, measure and match. Aftermarket aluminum pickets and rails in the same gauge and profile are a legitimate option and often cost less, but the anodized or powder-coat finish has to match closely or the new section will read as a different color within a season under San Francisco’s UV load. We source OEM-matched or quality aftermarket parts to your measured spec and tell you which one we’re using and why.
Groundwork Construction Co. of San Francisco is an independent service provider and is not affiliated with Jerith.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Fence Installation Is Failing
- Post feet rusting at the concrete line. Aluminum resists corrosion, but the base plate and anchor hardware take the brunt of salt fog and standing moisture. Once the powder coat lifts at that joint, the steel anchor starts to go.
- Pickets leaning out of plumb. This usually points to a loose post anchor or a footing that has shifted in San Francisco’s expansive clay soils after a wet winter. A single leaning section is a warning; three in a row means the footing is the problem, not the picket.
- Gate sag and dragging hinges. Gate frames carry the most load and the most swing cycles. Worn hinge pins or a stretched frame cause the gate to drop and scrape, and the latch stops catching.
- Finish chalking or peeling on sun-facing runs. South- and west-facing fence lines take the most UV. Chalky, faded panels aren’t just cosmetic; compromised coating is where corrosion begins.
- Rattling or loose rails in the brackets. Fasteners back out over time, and a loose rail lets the whole panel flex in wind. Left alone, the flex works the pickets loose from the rail.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Jerith-compatible aluminum fence installation in San Francisco, expect $4,130 to $10,620 installed. Linear footage, gate count, height, and footing conditions drive where you land in that range. A short run with one gate sits at the low end; a full property line with multiple gates and footings that need re-pouring climbs toward the top.
Every quote is line-item and upfront: parts, labor, footing work, and haul-away of the old section, so the number you see is the number you pay. No surprise change orders mid-job. We pull the required permits and pass inspection where the work calls for it. All workmanship is covered by our 730-Day Done Right Promise, and we offer $1,000 off projects over $10,000 plus 0% financing for 18 months for larger jobs.
DIY or Call Us?
You can safely check a few things yourself. Look for a model code on the gate frame or top rail, measure picket width and height, and note which sections lean or rattle. That information helps us quote accurately on the first call.
Where DIY goes wrong is the install itself. Setting posts plumb in San Francisco clay, matching footing depth to code, and getting the finish to match the existing run are the parts that separate a lasting fence from one that leans by the next rainy season. Aluminum fence installation is not a spring-loaded hazard, so there’s no safety panic here, but the tools and tolerance for a plumb, level, code-compliant install are a real barrier for most owners. If you’re weighing it, call us at (866) 320-2646 and we’ll talk through what your job actually involves.
Frequently Asked Questions
A properly installed Jerith aluminum fence commonly lasts 20 to 30 years in San Francisco’s coastal climate, with the finish and base hardware being the first things to need attention. Salt air near the beach shortens that window, so we spec corrosion-resistant hardware on those jobs.
Often yes. A single leaning section, a worn hinge, or a faded run can usually be repaired or re-coated without tearing out the whole fence. We’ll tell you honestly when a repair is the smarter spend versus a full replacement; call (866) 320-2646 for a free assessment.
Most Jerith fence installations in San Francisco finish in a single visit once parts are on hand and footings are set, though larger runs with multiple gates can stretch across a couple of days. We confirm the timeline in your written quote before any work starts.
We identify your fence line by model code where it exists and by measured spec where it doesn’t, then source OEM-matched or quality aftermarket parts to that spec. You’ll know exactly which part we’re using and its cost before we order it. Call (866) 320-2646 to start your free estimate.
Whether your fence needs a matching part, a re-leveled section, or a full replacement run, we’ll get you a clear, line-item quote and stand behind the work for 730 days. We also handle KraftMaid, Cambria, and Silestone projects across our other service lines. Call Groundwork Construction Co. of San Francisco at (866) 320-2646 for your free estimate, and a live person will pick up, day or night.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.