Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Bathroom Remodeling: The San Francisco Owner’s Guide
We install and repair Dvele bathroom remodeling systems and their components for San Francisco homeowners, with typical installed bathroom remodel costs running $10,620 – $33,040 depending on scope and fixture tier. Dvele builds panelized, off-site-constructed homes with integrated bathroom modules, and when a component inside that module starts to fail, the symptoms show up fast: a vanity that rocks against a factory-set wall panel, a shower valve that won’t hold temperature, or a supply line that weeps behind the access panel. Most San Francisco owners discover the problem during a routine walkthrough, or when a small leak stains the cabinet base below the sink. We’ve handled enough of these to know which parts fail first and how the Dvele assembly differs from a stick-built bathroom.
Which Dvele Models This Applies To
Dvele’s modular homes use factory-installed bathroom cores across their model lines, and the exact fixtures, valve cartridges, and shower trim vary by model year and floor plan. Before pricing anything, we pull the model and serial information usually found on the electrical panel door or the data plate near the mechanical room, then cross-reference it against the finish schedule. That schedule tells us the original faucet brand, valve series, and shower drain spec. Some Dvele builds shipped with standard off-the-shelf fixtures (often Kohler, Moen, or Delta-based components) that any plumbing supply house can match. Others used proprietary trim kits tied to a specific model run.
How to identify the right part
- Data plate or model plate: Look behind the electrical panel door or near the mechanical closet. The model number keys the finish schedule.
- Fixture labels: Faucet aerators, valve trim rings, and shower heads usually carry a brand stamp or part number on the underside.
- Measure the rough-in: A Dvele bathroom module often has shallower wall cavities than a stick-built bathroom, so the valve extension and drain rough-in measurements matter more than you’d expect.
The OEM-versus-aftermarket choice is real here. Factory-direct Dvele parts can take longer to source, while a high-quality aftermarket equivalent that matches the spec will often perform identically and cost less. We tell San Francisco homeowners which is which before we order.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Bathroom Remodeling Is Failing
Each symptom below points to a specific failure, and each one we’ve seen in Dvele modules across San Francisco:
- Vanity rocks or pulls away from the wall. The factory mounting anchors work loose over time, especially where the panel behind the vanity wasn’t reinforced for a heavy stone top.
- Shower valve won’t hold temperature. The cartridge inside the mixing valve wears out, and in Dvele modules the valve body sits behind a tighter wall cavity, so replacement needs the exact cartridge match.
- Water stains under the sink. A failing supply line or compression fitting weeps slowly, and because Dvele bathroom cabinets are often tighter to the wall, the leak hides longer.
- Shower pan or drain leaks. The factory-set drain can shift slightly with seasonal ground movement, and the seal at the pan-to-drain connection fails over time.
- Loose or cracked tile at seams. Dvele modules expand and contract as a unit, and rigid tile set at a panel seam cracks when the module flexes.
Replacement Cost & What’s Included
A full bathroom remodel on a Dvele module in San Francisco runs $10,620 – $33,040, and a small bathroom remodel lands at $5,900 – $14,160. What pushes you toward the top of that range: fixture tier, whether the valve or drain needs a full replacement versus a cartridge swap, and whether the wall panel behind the vanity needs reinforcement. A walk-in shower installation runs $5,310 – $14,160, and a tub-to-shower conversion runs $4,130 – $11,800. A shower replacement alone is $3,540 – $10,030, and a bathroom vanity installation is $945 – $3,540. We quote line-item pricing up front, so the number you see is the number you pay. Every job carries the 730-Day Done Right Promise and a written workmanship warranty.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check the obvious: tighten a loose vanity screw, look for moisture under the sink, and confirm the shower valve brand from the trim ring. Where DIY goes wrong on a Dvele module is the moment you open a wall cavity or touch the supply-side plumbing. The tighter wall construction leaves less room to maneuver, and a mis-seated fitting behind a factory panel can flood the cabinet below before you notice. Valve cartridge swaps on a Dvele module are also less forgiving of the wrong part number than a standard bathroom would be. If you’re past the “look and tighten” stage, call us. Our technicians have up to 12 years of experience, and calls are answered by a live person, 24/7.
FAQs
Most Dvele bathroom fixtures last 10 – 15 years, though supply lines and valve cartridges often fail sooner, closer to 7 – 10 years, depending on water chemistry in San Francisco. If you’re past that window and seeing drips or temperature swings, replacement is usually the right call rather than another repair. Call (866) 320-2646 for a free estimate.
Sometimes yes, especially for valve cartridges, supply lines, and vanity hardware, which can often be swapped without tearing into the module. Structural failures like a cracked shower pan seal or a loose drain connection usually call for replacement. We diagnose first and recommend the cheaper option when it’s sound. Call (866) 320-2646 to schedule a free estimate.
A focused fixture swap or vanity replacement is usually a single-visit job, while a full bathroom remodel runs longer depending on scope. We give you a realistic timeline in the written quote before work starts, so there’s no guessing. Call (866) 320-2646 for your free project estimate and design consult.
We start with your model and serial number, cross-reference the finish schedule, and confirm the part spec against an OEM or quality aftermarket equivalent. We also service KraftMaid, Cambria, and Silestone components if your Dvele build used them. Call (866) 320-2646 to get the part matched and priced.
Get Your Dvele Bathroom Priced in San Francisco
If your Dvele bathroom is showing the symptoms above, we can price the fix before anything else fails. We’re an independent service provider and not affiliated with Dvele, but our technicians work on these modules regularly, and we back every job with the 730-Day Done Right Promise. We serve homeowners across San Francisco, including Noe Valley, the Mission, and the Sunset. Call (866) 320-2646 for a free estimate and design consult, and take advantage of $1,000 off projects over $10,000 plus 0% financing for 18 months.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.