Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mighty Buildings Home Additions & ADU: The San Francisco Owner’s Guide
We build and finish Mighty Buildings-compatible additions and ADUs throughout San Francisco, with installed projects typically landing between $53,100 and $153,400 for an addition and $106,200 to $259,600 for a full ADU. That range covers factory-built structure, foundation, site work, utility tie-ins, finishes and inspection. If you own a Mighty Buildings panelized shell and something is already going wrong – a panel seam opening, a wet spot at a connection, a door that no longer sits square – you’re in the right place. We’re an independent construction company, not affiliated with Mighty Buildings, and we work on their structures every month in this city.
Owners usually find out the hard way. Water shows up on the interior drywall after a Pineapple Express storm, a corner seam starts letting in air, or a floor edge feels soft underfoot near a bathroom wall. The cause is almost always at a joint, a flashing detail or a penetration point, not in the panel itself.
Key Takeaways
- Installed addition pricing in San Francisco starts around $53,100 and climbs with site access and utility work.
- Failures concentrate at panel joints, roof-to-wall transitions and utility penetrations – not the structural shell.
- We pull permits, schedule inspections and back the work with our 730-Day Done Right Promise.
- Calls reach a live person 24/7, so you’re not waiting until Monday when a seam starts leaking.
Which Mighty Buildings Models This Applies To
Mighty Buildings built its reputation on large-format 3D-printed and panelized units, and the assemblies vary by generation. Older studio and one-bedroom shells use a different wall-to-floor connection than the later two-bedroom ADU configurations. That matters because the flashing profiles, gaskets and connector hardware are not interchangeable between generations. Before we quote anything, we identify your structure by reading the panel label inside the mechanical chase or on the interior face of an exterior wall, then measure the actual joint width with a caliper. A 2mm difference in seam geometry changes which gasket profile fits.
The OEM-versus-aftermarket decision is real here. Mighty Buildings-specific connectors and proprietary gaskets sometimes have a long lead time. For many repairs, a tested aftermarket equivalent – a compatible EPDM gasket, a standard panel flashing, a code-compliant connector with matching load ratings – performs the same or better and costs less. We tell you which is which, in writing, before you decide. Where a proprietary part is genuinely required for warranty integrity on the shell, we say so. We don’t carry stock and we don’t keep parts on a truck; we source to your specific model and schedule the install.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Mighty Buildings Home Additions & ADU Is Failing
- Water staining at interior panel seams. Gasket compression has relaxed or the sealant at the joint has aged out. Left alone, moisture wicks into the drywall and framing behind it.
- Drafts or cold spots near a corner or window opening. The flashing detail at the penetration has separated from the panel face, opening a path for air and water.
- A door or window that won’t close square. Usually a sign that a connection point has shifted, not that the frame itself is bad.
- Soft or bouncy flooring at an edge. Water has reached the subfloor through a failed perimeter seal, often after a wet winter in a neighborhood like Noe Valley or the Sunset where fog and rain hit hard.
- Visible cracks along a seam or at the roof-to-wall junction. Thermal movement over a couple of seasons has opened a joint that needs re-sealing and possibly re-flashing.
In San Francisco, the pattern is seasonal. We regularly see joint failures surface in February and March after months of fog cycling into sun, because the panel faces expand and contract at different rates and the sealant takes the stress. Additions on sloped lots in Bernal Heights or Twin Peaks see more movement at the uphill connection than flat-lot builds in the Mission.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what San Francisco homeowners actually pay for Mighty Buildings-compatible work, in installed ranges:
| Scope | Installed Range |
|---|---|
| Home addition (Mighty Buildings-compatible) | $53,100 – $153,400 |
| ADU construction | $106,200 – $259,600 |
| Garage conversion | $35,400 – $94,400 |
| Targeted seam, flashing or connector repair | Quoted per job after site inspection |
What drives the range: site access (a narrow lot off a steep street costs more to stage), utility tie-in distance to the main, whether a new foundation or an existing slab is used, finish level, and permit and inspection fees specific to San Francisco. Your quote is line-item and fixed. The number we write is the number you pay, with no change orders for scope we already priced. Every project carries our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction – if it’s not done right, we make it right. We also offer $1,000 off projects over $10,000 and 0% financing for 18 months.
DIY or Call Us?
Some checks are safe and worth doing. You can photograph a seam, note where water appears and when, measure a joint gap with a ruler, and confirm your model from the interior panel label. That information helps us quote accurately and saves a trip.
What we don’t recommend is opening a sealed panel joint, re-flashing a roof-to-wall transition, or re-torquing structural connectors yourself. Those details sit behind the weather barrier and load path. Get them wrong and you’re looking at water intrusion into framing or a connection that fails inspection – both far more expensive than the original repair. This is envelope and structural work, and it needs a trained hand who knows the assembly.
Call (866) 320-2646 and a live person answers, day or night. We’ll schedule a free estimate and design consult, walk the structure with you, and give you an upfront price in writing.
FAQs
The structural panels are built to last decades; the seals, gaskets and flashings around them are the parts that age out first, typically within 8 to 15 years depending on exposure. Coastal fog and rain cycling speed that up on west-facing walls. Call (866) 320-2646 for an inspection and exact quote – estimates are free.
Often yes. A single relaxed gasket or a separated flashing can be re-sealed and re-detailed without touching the panel, which keeps cost down and preserves the shell. We only recommend replacement when the joint geometry itself has failed. Call (866) 320-2646 and we’ll tell you honestly which you need.
A targeted seam or flashing repair is usually a one- to two-day job; larger connection or envelope work runs longer and depends on permit timing with San Francisco’s Department of Building Inspection. We give you a realistic schedule in writing, not a guess. Call (866) 320-2646 to get yours.
We identify your exact model from the panel label and measurements, then source either the proprietary part or a tested aftermarket equivalent that meets the same load and weather spec. We tell you which and why before ordering. Call (866) 320-2646 to start the process – estimates are free.
We also work with KraftMaid, Cambria and Silestone finishes when an addition or ADU needs cabinetry or counters.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.