Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Impact Windows & Doors in San Francisco: What the Job Actually Involves
Impact window installation in San Francisco runs about $9,440 to $29,500 for a typical home, and a full-house impact window and door package usually takes one to three weeks of install time after a four-to-eight-week order and permitting lead. These are laminated or laminated-plus-secondary-glazing assemblies rated for wind-borne debris, and in this city they earn their keep against salt-laden fog and Pacific gusts as much as against any storm. Call (866) 320-2646 for a free on-site estimate.
How the work runs, stage by stage
Impact units aren’t a swap-and-go job. The sequence below is what a real install looks like on a San Francisco home, with the decisions that land on you at each step.
Stage 1: Site measure and opening survey (half a day)
We measure every rough opening, check square and plumb, and photograph the existing frames. On the 1880s-1920s Victorians and Edwardians that make up so much of the housing stock, frames are rarely true and the reveal often hides old rot. This is where you decide whether each opening gets a full-frame replacement or an insert, because that choice drives both price and schedule.
Stage 2: Order and permits (four to eight weeks)
Impact glass is built to spec and doesn’t come off a shelf, so once you sign off on the line-item quote the units go into production. In parallel we pull the building permit. You’ll make your final glass and finish selections here, and this is the long pole in the timeline, not the install itself.
Stage 3: Demolition and prep (one to two days per elevation)
We remove the old units, cut back any rotted framing, and check the flashing and sill pans. Coastal damp means old sills are often soft. We replace the damaged wood, set new galvanized flashing, and stage the openings for weather before the new units go in.
Stage 4: Installation (two to four days per elevation)
Units set into the openings, shimmed, squared, fastened, and sealed with a compatible sealant. Hardware gets stainless screws and hinges. Doors are hung and checked for swing and latch before we move on. You’ll walk each elevation with us as it’s finished.
Stage 5: Seal, finish, and inspection (one to two days)
Final sealing, interior trim, and touch-up. We schedule the inspection and stay on site for it. Then a full walkthrough where you check every operating unit and sign off. On most jobs the homeowner’s only real decisions are glass spec, frame finish, and insert-versus-full-frame at each opening.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices you’ll weigh before the order goes in
- Laminated glass vs. laminated-plus-secondary glazing. Standard laminated handles most residential loads and costs less; a secondary glazed assembly adds impact resistance and noise control at the higher end of the range. Your exposure and how close you sit to the coast decide it.
- Frame material. Vinyl is the value pick and handles salt air well. Aluminum and fiberglass hold dimension better on large openings and steep hillside framing. Where a James Hardie-clad trim detail matters on the exterior, we spec the frame to match.
- Full-frame vs. insert replacement. Full-frame is more invasive but lets us fix the rot and flashing behind old units. Insert is faster and cheaper where the existing frame is sound.
- Finish and color. Coastal homes here tend toward darker exterior frames; the trade-off is heat gain, which the glass coating offsets. Interior finishes range from a natural wood tone to a factory finish matched to your trim.
- Door hardware and swing. Stainless hinges and multipoint locks are worth the upcharge on salty elevations. We don’t cut corners here because standard hardware corrodes fast.
What Impact Windows & Doors cost in San Francisco, CA
Impact window installation in San Francisco lands between $9,440 and $29,500, and that spread is driven by real variables, not sales pressure. Here’s what moves the number:
- Number and size of openings. The biggest single factor. A handful of windows sits at the low end; a full-house package with large doors climbs to the top.
- Insert vs. full-frame. Full-frame adds labor and wood replacement, especially on older stock.
- Glass spec. Secondary glazing and higher performance coatings push toward $29,500.
- Existing condition. Rotted sills, out-of-square frames, and hidden rot add repair time and material.
- Permit scope. Doors and structural openings add to the permit and inspection load.
A written line-item estimate from us spells out every unit, the glass spec, frame finish, and the labor and permit costs. What it won’t include without a note is unforeseen rot found mid-demo, since we can’t see inside a frame until we open it. Call (866) 320-2646 for an exact quote – estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco homes do to this job
This city is dense, historic, and built on steep hills, and that shapes every install. The combination of pre-1906 and post-1906 rebuild stock, soft-story seismic retrofit mandates, and neighborhood design review makes permitting and structural work unlike anywhere else in the Bay Area. On a hillside lot, a window opening may sit in a wall that’s been retrofitted and re-framed, and we check that before we order. Near Twin Peaks and the west-side hills, salt and fog corrode fasteners and hardware years faster than inland, so we spec stainless and galvanized as standard, not an upgrade. Edwardsians in the Mission and Noe Valley often need a discretionary review before exterior changes, so we build that timeline into the quote. Across San Francisco we see the same failure we handle constantly: fog-belt homes where old wood windows have rotted at the sill and the hardware has pitted, long before the glass itself was ever the problem. We work throughout San Francisco and the surrounding area.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Impact Windows & Doors in San Francisco
Plan on one to three weeks of install time for a typical package, with four to eight weeks of order and permit lead time before the crew arrives. The lead time dominates, so early ordering matters more than early scheduling.
Yes. Like-for-like replacement generally needs a building permit, and changes to openings or structure add to that. We pull the permit and handle the inspection. Call (866) 320-2646 for a free estimate and we’ll walk the permit scope with you.
In most cases yes. Same-size replacements don’t touch plumbing or structure. Resizing or adding an opening is a different job, and we’ll flag it before work starts.
Not for anything in the written line-item quote. Unforeseen rot found mid-demo is the one variable, and we stop, show you, and re-quote before proceeding. The number you see is the number you pay.
Every project carries our 730-Day Done Right Promise, which covers workmanship for two full years. If it’s not done right, we make it right. Call (866) 320-2646 to schedule your free estimate.
Get a free estimate on Impact Windows & Doors in San Francisco
Call (866) 320-2646 and a live person answers, any hour, any day. We’ll schedule a free on-site estimate, measure your openings, and hand you a written line-item quote covering every unit, the glass spec, and the permit scope. No surprises. If you’re planning a wider exterior project, this often pairs with a Aluminum Fence in San Francisco or an Iron Fence in San Francisco. For the broader scope, see our Windows & Doors service, or the Windows & Doors in San Francisco page. You can also read more about how we work across San Francisco.
Written by the team at Groundwork Construction Co.