Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sliding & Patio Doors in San Francisco: What the Job Really Involves
Replacing or installing sliding and patio doors in San Francisco typically runs $5,310 – $17,700 for a standard replacement and $9,440 – $29,500 when you’re cutting a new opening or going to impact-rated glass, with most single-door swaps finished in one to two days. San Francisco is a tight-clearance city, so the door you pick has to fit the opening you actually have, not the one on the brochure. Call (866) 320-2646 and we’ll walk you through what your specific opening can hold.
How We Run a Sliding & Patio Door Job, Stage by Stage
Sliding and patio doors fail differently than a fixed window, so the sequence matters. Here’s the real order of operations.
Stage 1: Measure and open the wall (day 1, 2 – 3 hours)
We measure the rough opening, check that the header and framing are sound, and confirm the track is level. On a San Francisco row house, this is where we find out whether the last install left a square opening or a slightly racked one. You decide the door model and swing direction (or slide direction) before we order anything.
Stage 2: Demo and prep (day 1, 3 – 5 hours)
The old door comes out, the flashing and sill get inspected, and any rot in the framing gets cut back and replaced. On the west side, this is often the moment we find soft wood behind the trim from years of fog and salt. You confirm whether we repair framing or replace a section before we close it up.
Stage 3: Set the door and seal it (day 2, 4 – 6 hours)
The new unit goes in, gets shimmed level and plumb, and the perimeter is flashed and sealed. Then the hardware, rollers, and locking mechanism get installed and adjusted. You test the slide and the lock yourself before we move on.
Stage 4: Trim, finish, and inspect (day 2, 2 – 3 hours)
Interior and exterior trim go on, the threshold gets checked for water shedding, and we run the door through a full open-close cycle. If a permit was pulled, this is when the inspection gets scheduled.
Stage 5: Final walkthrough (day 2 – 3, 30 minutes)
We hand over the warranty paperwork and show you how to adjust the rollers and clean the track. Any punch-list items get written down and scheduled. Most jobs are done by day two; complex openings run to day three.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
- Vinyl sliding doors – the workhorse pick. Holds up well against damp and salt, low maintenance, and lands on the lower end of the price range. Best for rentals and budget-conscious replacements on the fog belt.
- Aluminum sliding doors – lighter frames, good for large glass panels and modern high-rise units. Needs a thermal break in San Francisco’s marine climate to avoid condensation.
- Wood-clad or fiberglass patio doors – the best balance of looks and durability. Fiberglass resists rot and moisture better than wood; wood-clad gives you the traditional look that fits Victorian and Edwardian row houses. Higher up the price range.
- Impact-rated glass – worth considering for large openings and low-slope or hillside homes where wind exposure is real. Adds cost but pays back in durability and insurance favor.
- Security hardware – multi-point locking, anti-lift rollers, and reinforced strike plates. On a San Francisco alley-facing door, this is the difference between a door and a weak point.
We spec hardware from brands like Therma-Tru on the door systems and Mr-Glass on the glazing, and we won’t put a standard screw into an exterior door on the west side. Stainless is the starting point, not the upgrade.
What Sliding & Patio Doors Cost in San Francisco, CA
Standard replacement runs $5,310 – $17,700. Cutting a new opening or going to a full glass wall takes you to $9,440 – $29,500. Here’s what moves the number:
- Opening size and glass area – a standard 6-foot slider sits at the low end; a 12-foot panoramic glass wall pushes toward the top.
- Existing condition – if the framing is sound and the opening is square, the job stays lean. Rot, soft framing, or a racked opening adds days and dollars.
- Relocating structure or electrical – moving a header, adding a beam, or rerouting wiring near the opening is a real cost jump, not a footnote.
- Material grade – vinyl at the low end, wood-clad and fiberglass mid, impact-rated glass high.
- Permit scope – a straight swap often doesn’t require a permit; a new opening or structural change does, and that adds time and fees.
Every estimate is itemized in writing, and the number you see is the number you pay. We pull permits where the scope requires it and pass the inspection, and there are no change orders for work we should have priced upfront. The 730-Day Done Right Promise covers workmanship for two years.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco Homes Specifically Do to This Job
Almost every sliding and patio door job in San Francisco runs into the same two walls: historic housing stock and a permitting gauntlet that can eat a year before a shovel moves. The 1880s – 1920s Victorian and Edwardian row houses we work on throughout Noe Valley, the Mission, and the Inner Sunset have brick foundations and wood-frame walls that were never built to square, and the rear openings often face an alley with tight loading access. On the west side, marine fog and salt air rot and corrode standard hardware fast, so we spec stainless and galvanized flashing even on a small swap. Soft-story seismic retrofit work on older multifamily buildings sometimes happens right next to a door replacement, and it changes how the opening has to be framed. If the job grows into a full exterior scope, that’s part of a Windows & Doors in San Francisco project and we’ll scope it together.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Sliding & Patio Doors in San Francisco
Most single-door replacements take one to two days, and new openings with structural work run two to three. The door order itself usually takes two to four weeks to arrive. Call (866) 320-2646 for a timeline on your specific opening.
A like-for-like swap in the same opening usually doesn’t require a permit; a new opening, a size change, or any structural work does. We confirm the scope against your address before quoting. Call (866) 320-2646 and we’ll tell you what applies to your job.
Yes, in most cases. If the existing opening is square and the header is sound, it’s a direct swap and no plumbing or framing gets touched. When a size change forces a header move or wiring reroute, that’s a separate line item in the estimate.
Standard replacement runs $5,310 – $17,700 and a new opening or impact-rated glass runs $9,440 – $29,500. Call (866) 320-2646 for a written, itemized quote – estimates are free.
Workmanship is covered by our 730-Day Done Right Promise, and the door itself carries the manufacturer’s warranty. If something isn’t right, we make it right. Call (866) 320-2646 to schedule your free estimate.
Get a Free Estimate on Sliding & Patio Doors in San Francisco
Call (866) 320-2646 for a free on-site estimate. We’ll measure your opening, confirm the door type and hardware, and hand you an itemized written price with no surprises. A live person answers around the clock, and technicians show up in uniform and background-checked. If you’re also weighing exterior work, homeowners often pair this with Fence Repair in San Francisco or, on a driveway project, Paver Driveways in San Francisco. We cover all of San Francisco, and you can explore the full Windows & Doors scope anytime.
Written by the team at Groundwork Construction Co. of San Francisco.