Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Impact Windows & Doors in Daly City: What the Job Actually Involves
Impact window installation in Daly City runs $8,000 – $25,000 for a typical whole-house package, and most single-family jobs are measured in three to five working days once the order lands. The work itself is about replacing the weak link in a wind-resilient envelope: laminated glass that won’t shatter into the living room, frames rated to hold pressure, and door hardware that latches under load. Call (866) 320-2646 and we’ll walk your exterior and price it.
How We Take a Daly City Home From Old Glass to Rated Openings
Every job here moves through the same five stages. Skipping one is how impact windows & doors end up leaking at the sill two winters later, so we don’t skip them.
Stage 1: Exterior assessment and measurements (day 1, 2 – 3 hours)
We walk the outside of the house and photograph every opening, then check frame condition, stucco around the perimeter, and whether the rough openings are square. On the post-war stucco homes we work on most in Daly City, this is where we find soft wood at the sill or a header that’s pulled loose. You decide at this stage whether to replace that rot now or revise scope. Measurements get taken to the sixteenth of an inch so the factory order isn’t wrong.
Stage 2: Permit filing and product selection (days 2 – 10)
We pull the permit and put the spec sheet in front of you: glass package, frame material, U-factor and design pressure rating, screen type, and hardware finish. You sign off on the exact order. This is the one stage where nothing happens on the house, and it’s also where the long lead times live. Standard sizes arrive faster; custom colors and non-standard widths can add two to four weeks.
Stage 3: Demo and rough prep (day 1 of install, 3 – 6 hours per opening cluster)
Old units come out, and we open the wall back to sound framing. Stucco gets cut clean rather than hammered, which keeps the repair patch small. We check the rough opening for square, flash the sill, and set a pan if the opening sits low enough to collect water. Any rotted framing gets sistered or replaced before a single new unit goes in.
Stage 4: Setting, shimming, sealing (days 1 – 3 of install)
New units get shimmed plumb, fastened per the manufacturer’s nailing pattern, and flashed in the sequence the manufacturer specifies. We use two beads of sealant at every joint where stucco meets frame, and we don’t caulk over a gap that should have been flashed. Doors get their hinges and multi-point hardware set in this stage. Each opening gets its own final water test before we move on.
Stage 5: Stucco repair, trim, and inspection (days 3 – 5)
We patch the stucco, install interior trim, and set the door thresholds. The city inspection happens after all openings are in and flashing is visible. You walk the job with us, we label every unit, and the punch list gets worked before we call it finished. Your final decision point: which openings get the upgrade now and which wait, which we price both ways.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make on Impact Windows & Doors
Spec selection is where a job lands near $8,000 versus near $25,000. These are the real forks in the road.
- Frame material. Vinyl is the budget workhorse and holds up well in fog, but it comes in limited color depth. Aluminum is slimmer and stronger, and it’s the better fit for wide openings and large sliders, though it conducts heat and needs a thermal break. Wood-clad gives the warm interior look, at a premium. Andersen and Marvin both make solid rated lines if you want a name you can look up.
- Glass package. Impact-rated laminated glass is the baseline. Upgrading to a low-E coating and a more insulated glazing assembly keeps interior condensation down in a cold, damp climate, which matters more here than in a dry inland city.
- Opening configuration. Fixed and awning units are sealed shut and cheapest per square foot. Casement and slider units carry moving hardware that needs to be rated. Doors are the biggest variable: a pivot door costs more than a standard hinged unit, and a rated multi-point lock system costs more than a single latch.
- Hardware and finish. Standard finishes are included. Custom color and premium hardware add meaningful cost, and the lead time grows with it.
- Screen and insect protection. Standard screens are fine. Impact-rated screen systems that need to survive the same wind load cost more and are worth it on openings facing the ocean side of the house.
What Impact Windows & Doors Cost in Daly City, CA
In Daly City, impact window installation runs $8,000 – $25,000, and a standard window replacement without the impact rating lands across the $4,500 – $15,000 range for comparison. The five things that move the number:
- Number and size of openings. A ten-opening house and a twenty-opening house are different jobs. Large sliders cost more per unit than narrow casements.
- Existing condition. Rotted framing, failed stucco, or a rough opening that isn’t square adds carpentry hours. On older Daly City stock, this is the most common surprise.
- Structural changes. Widening an opening or adding a new one requires header work and a larger permit scope. A straight swap doesn’t.
- Spec and material grade. Vinyl to wood-clad, standard to custom color, one latch to multi-point hardware: each step up is a real line item.
- Permit scope and access. A hillside lot where the crew has to stage on a narrow street, or a second-story opening that needs lift access, adds labor. The permit itself is a defined line item in the written estimate.
Our written estimate breaks out product, labor, permit, and repair as separate lines, so you see where the money goes. What’s typically not included: HOA fees if your community has architectural review, and any structural repair discovered mid-job that wasn’t visible at the initial walk. Those get a change order quote before anyone touches them.
See the difference
Before
After
Before
After
Before
AfterWhat Daly City Homes Specifically Do to This Job
Daly City is fog country, and the housing stock shows it. The dense rows of 1940s – 1960s stucco-over-wood-frame homes rise on steep slopes where wind-driven rain hits the same wall faces year after year, and that moisture is what kills window frames and door jambs from the inside out. On the hillside streets off Mission and around Westlake, we open a wall expecting a straightforward swap and find soft sill wood, failed flashing, or original single-pane units that have been leaking for a decade. We cover Daly City’s 94015, 94016, 94017, and 94014 zip codes, and the permitting question on a hillside lot is where this job gets its personality: narrow lots, neighbors’ walls feet away, and staging that has to be planned around tight access. We pull the permit, we schedule the inspection, and we don’t start install until the flashing plan is approved. On doors, the reinforcement is the whole point: rated hinges, a multi-point latch that engages in three places, and a threshold that sheds that wind-driven rain instead of pooling it at the jamb. A failing door before a storm is a door that doesn’t latch; the time to fix it is the dry season, not the night the wind arrives. Homeowners planning the exterior as a package often pair this with Aluminum Fence in Daly City for the side yard, or Iron Fence in Daly City where the wind load on an exposed run of fence has been an issue. It’s also a natural fit as part of a full Windows & Doors in Daly City scope when you’re replacing everything at once.
Serving Daly City, CA – Our Local Coverage Area
We serve Daly City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Impact Windows & Doors in Daly City
Plan on three to five working days of install time, plus the product lead time, which runs from a few weeks for standard sizes to six weeks or more for custom colors. The permit and measurement stages add another ten days to two weeks on the front end. Call (866) 320-2646 with your opening count and we’ll give you a realistic calendar date, not a guess.
Yes. Window and door replacement that changes the opening or the exterior envelope requires a permit in Daly City, and impact-rated units involve a design pressure rating the inspector will want to see documented on the spec sheet. We handle the filing, the inspection scheduling, and the paperwork. Call (866) 320-2646 and we’ll explain what your specific scope triggers.
In most straight replacements, yes. We’re swapping units into existing openings, so no plumbing moves and no framing is altered. The exception is when we find rot or a rough opening out of square, and that gets quoted before we touch it. Call (866) 320-2646 for a walk-through that identifies those risks up front.
Impact window installation runs $8,000 – $25,000, and doors are priced per unit on top of that. A standard non-impact window replacement sits at $4,500 – $15,000, so the impact rating is a real premium you’re choosing deliberately. Call (866) 320-2646 for a line-item quote – estimates are free.
Every job is covered by our 730-Day Done Right Promise, which means if something isn’t done right, we make it right for two full years. Manufacturer warranties on the glass and frames run alongside it. Our technicians have up to 12 years of experience, and they’re background-checked and in uniform on every job. Call (866) 320-2646 with any warranty question before you sign anything.
Get a Free Estimate for Impact Windows & Doors in Daly City
We’ll come out, photograph every opening, check the framing and stucco while we’re there, and hand you a written line-item quote that separates product, labor, permit, and repair. You’ll know the total before anyone orders glass. Estimates are free, financing runs at 0% for 18 months, and projects over $10,000 get $1,000 off. One call gets it started.
Groundwork Construction Co. of San Francisco
(866) 320-2646
Written by the team at Groundwork Construction Co.