Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Driveway Repair & Replacement in Mill Valley, CA: What It Takes and What It Costs
Driveway repair and replacement in Mill Valley typically runs $5,000 – $14,000 for a full replacement, with most hillside driveway jobs landing in the $7,000 – $18,000 range once drainage, slope stabilization, and paver finish are factored in. The work itself is usually a 2 – 5 day job once permits clear, though Mill Valley’s discretionary design-review process can add 3 – 6 weeks before a crew ever breaks ground. Call (866) 320-2646 to schedule a free on-site estimate.
How We Run a Driveway Repair & Replacement Job, Start to Finish
Mill Valley homeowners don’t want a crew showing up three times to do what should take one pass. The rural and acreage properties up on the hillsides mean longer service drives, heavier loads, and no patience for a half-finished job. Here’s the actual sequence.
Stage 1: Site Assessment and Access Plan (Day 0, about 90 minutes)
We walk the drive, measure the grade, and check where water actually goes when it rains. On Mill Valley‘s single-lane hillside streets with no turnaround, this is also where we plan how a dump truck and a plate compactor get in and out without blocking a neighbor. You’ll decide right here whether we’re patching or replacing, and whether the existing drive can take a top course or needs full demo.
Stage 2: Permit Pull and Utility Locate (3 – 6 weeks, weather and scope dependent)
Mill Valley requires a permit for full driveway replacement and for any work that changes drainage or ties into the storm system. We pull it, call for utility locates, and get the design-review sign-off if your lot triggers it. You sign off on the final material and finish during this window so nothing stalls once the permit lands.
Stage 3: Demo and Base Prep (Day 1 – 2)
We break out the old surface, haul it off, and cut down to stable subgrade. On hillside lots the base is where jobs succeed or fail: we compact in lifts, add a geotextile separation layer where the soil is expansive, and set the cross-slope so runoff sheds away from the house instead of pooling at the garage door. This is the longest single stage and the one worth paying attention to.
Stage 4: Install (Day 2 – 4)
Concrete pours and cures; pavers get set on a compacted bedding layer with edge restraint; asphalt goes down in lifts and gets rolled. We form and finish the apron, the expansion joints, and any transitions to the garage slab. You’ll see the grade line here – if it looks high or low at the door, we fix it before we leave.
Stage 5: Drainage Check, Cleanup, and Walkthrough (Final day)
We run water across the finished surface to confirm it moves where it should, clean up the spoils, and walk the job with you against the written scope. Any correction gets logged and handled before we call it done. That walkthrough is what the 730-Day Done Right Promise backs up – if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
- Concrete, standard broom finish: the most common replacement in Mill Valley, roughly $4,500 – $12,000. Holds up well if the base is right, but hillside movement shows as cracks within a few seasons. Suits a straight drive with good drainage.
- Concrete with stamped or colored finish: same structural base, more money, better curb appeal on a visible drive. Good pairing with the shingle-cottage streets near downtown where the front elevation is part of the property’s character.
- Asphalt: roughly $3,500 – $9,000, the low-cost option for a longer rural service drive. Cheaper up front, needs sealing every couple of years, and softens on steep grades in a hot summer.
- Pavers: roughly $7,000 – $18,000. Highest up-front cost but the most repairable – pull a section, reset it, done. On a long acreage drive where a root lift or a utility dig is likely, that matters. Belgard makes a solid range for this.
- Drainage and edge details: channel drains, French drains, and a thickened edge are add-ons most hillside jobs need. Skipping them is the most common reason a new drive fails in the first wet winter.
If the driveway is part of a bigger exterior scope, it pairs naturally with our Driveway & Pavers service.
What Driveway Repair & Replacement Costs in Mill Valley, CA
Full driveway replacement in Mill Valley runs $5,000 – $14,000. Paver driveway installation runs $7,000 – $18,000, concrete installation $4,500 – $12,000, and asphalt $3,500 – $9,000. Sealing a drive that’s still sound runs $250 – $700 and is often all a homeowner needs.
Five things push a job from the low end to the high end:
- Length and width: a rural acreage drive is often two to three times the square footage of a standard suburban drive, and it’s priced per square foot.
- Existing condition: a cracked but stable surface can take a top course. A drive with failed subgrade, root heave, or a settled hillside corner needs full demo and base rebuild.
- Grade and access: steep slopes require thicker base, more compaction, and sometimes a retaining edge. Single-lane access with no turnaround on a Mill Valley hillside street can mean a longer demo and extra labor for material handling.
- Drainage work: channel drains, trench drains, and tie-ins to the storm system add real cost but prevent the washout that would eat the savings.
- Material grade: the jump from asphalt to pavers is roughly $4,000 – $9,000 on a typical drive, and part of what you’re buying is future repairability.
A written estimate from us is line-itemed: demo, haul-off, base, drainage, material, and finish. What’s typically not included: landscape repair beyond the drive edge, root removal on a protected tree, and any unpermitted work discovered on the existing drive. We tell you those up front rather than at the end. Call (866) 320-2646 for an exact quote – estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Mill Valley Homes Specifically Do to This Job
Mill Valley is a site-specific engineering puzzle before it’s a paving job. Hillside lots, tight tree-lined lanes, and a discretionary design-review process mean nothing here is off-the-shelf – and steep drives off streets like those climbing above downtown or in Tamalpais-Homestead Valley need drainage planned before the first paver goes down. On many of these streets, staging and material delivery mean navigating single-lane roads with no turnaround, so crews run a spotter and pre-dawn delivery windows. We see the same failure modes repeatedly: early-1900s redwood and shingle cottages near downtown with driveways that have settled into old foundations and no drainage at all; 1950s – 70s ranch and split-level homes on the hillsides where a tree root has lifted a concrete slab and water now runs back toward the garage. Marin’s wet winters and long dry summers put real stress on the surface, and wildfire exposure adds a materials question – non-combustible finishes and ember-resistant detailing matter more here than on a flat suburban lot. Across ZIP codes 94942 and 94941, we plan for the season, not the sale. We cover all of Mill Valley and the surrounding hills.
Serving Mill Valley, CA – Our Local Coverage Area
We serve Mill Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Driveway Repair & Replacement in Mill Valley
A driveway repair and replacement in Mill Valley usually takes 2 – 5 days of on-site work once the permit clears, with the permit and design-review window adding 3 – 6 weeks on most hillside jobs. Simple repairs – sealing, patching, edge reset – can finish in a day. Call (866) 320-2646 to schedule a free estimate and we’ll give you a dated schedule for your lot.
Yes – Mill Valley requires a permit for full driveway replacement and for any work that changes drainage or ties into the storm system. Patching and sealing generally don’t trigger one, but a change in grade or runoff path often does. We pull the permit and handle the inspection as part of the job.
In most cases yes – we call for utility locates and design the base around existing gas, water, and electrical runs. If a line sits so shallow that a base rebuild would hit it, we’ll tell you before demo and price the relocation as a separate line. For a larger project that involves a new structure, homeowners often pair this with ADU Site Prep & Utilities in Mill Valley so the drive and the utilities get planned together.
Driveway replacement in Mill Valley typically runs $5,000 – $14,000, with paver drives at $7,000 – $18,000 and asphalt at $3,500 – $9,000. Sealing a sound drive is $250 – $700. The range depends on square footage, existing condition, grade, access, and drainage scope. Call (866) 320-2646 for an exact quote – estimates are free and line-itemed.
Every driveway repair and replacement we do is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing. It covers our install, including base, finish, and drainage details we installed. Call (866) 320-2646 to schedule your free estimate.
Get a Free Estimate for Driveway Repair & Replacement in Mill Valley
If your drive is cracked, rutted, pooling water at the garage door, or just overdue, call (866) 320-2646 for a free on-site estimate. We’ll walk the grade, check the drainage, and hand you a written line-item quote with no surprises. A live person answers around the clock, and your number is the number you pay. Considering a bigger project alongside the driveway? We also handle Junior ADU & Interior Conversion in Mill Valley – sometimes it makes sense to plan both together.
Written by the team at Groundwork Construction Co.