Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sliding & Patio Doors in Corte Madera: What the Job Actually Involves
Sliding and patio door replacement in Corte Madera usually runs $3,800 to $11,500 for a single opening, including removal, framing corrections, flashing, and finish work, with most jobs finished in one to three days once the unit is on site. Custom sizes, multi-panel systems, and hillside or flood-zone openings push toward the top of that range. Call (866) 320-2646 and we’ll set a free on-site estimate so you get a real number, not a phone guess.
How a Sliding & Patio Doors Project Runs, Start to Finish
Every opening we touch follows the same five-stage sequence. The stages don’t change much. The durations do, and so does what you’re deciding at each one.
1. Measure and scope (day 1, about 60 to 90 minutes)
We measure the rough opening, check the header and sill for rot or settling, and confirm the door swings or slides where you want it. On Corte Madera hillside lots, this is also where we look at how the deck or grade meets the threshold, because that’s where water gets in. You decide on configuration and glass package by the end of this visit. A written line-item quote follows, and the number you see is the number you pay.
2. Order and permit (week 1 to 4)
Standard sizes land in two to three weeks. Custom multi-panel units and anything with a specialty finish can run four to six weeks. If your home sits in one of the low-lying flats near Corte Madera Creek or the marsh side of Town Center, add time for elevation review, since a door replacement that alters the opening can trigger a floodplain check. We handle the permit paperwork and the inspection scheduling.
3. Demo and framing prep (day 2, four to six hours)
Old door comes out, and this is where surprises show up. On 1950s and 60s ranchers around Christmas Tree Hill and the older flats, it’s common to find a rotted sill plate or a header that was never sized for a heavier door. We rebuild the opening square and level before anything new goes in. You don’t have to decide anything here unless we hit structural rot, and then we call before we spend.
4. Install, flash, and seal (day 2 into day 3)
New unit sets into a properly flashed opening, shimmed and anchored per manufacturer spec. Glass goes in, hardware gets adjusted, and the whole perimeter gets sealed and trimmed. Most single openings finish in a day. A multi-panel slider or a French door pair takes into day three.
5. Final walkthrough and inspection sign-off (day 3, about 30 minutes)
We operate the door with you, check the slide or swing, confirm the lock and screen, and hand over the paperwork. If a permit was pulled, the inspection happens after. The work is covered by our 730-Day Done Right Promise, so if something isn’t right, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the decisions on this job come down to four choices, and each one trades cost against how the door holds up in Marin’s wet winters.
- Vinyl sliders: The value pick. Good thermal performance, low maintenance, and the least expensive path. They suit the mid-century ranchers well. Downside is the frame profile is bulkier, so sightlines are heavier and it doesn’t match a custom home’s trim detail.
- Fiberglass and steel-clad patio doors: Therma-Tru makes a strong fiberglass entry and patio line that takes paint and stain and won’t dent like steel. Better for a custom finish, and it holds up to moisture. Costs more than vinyl, less than wood.
- Wood and wood-clad: The choice for the two-story customs going up on the hillside lots. Warm, matches interior trim, and takes a stain. It needs upkeep, and on the flood-zone side of town you want a clad exterior so the wet side isn’t bare wood.
- Multi-panel and lift-slide systems: Large glass, minimal frame, and the indoor-outdoor feel that a lot of Corte Madera rebuilds are after. This is where the price jumps. It also means more structural work at the header.
Glass matters as much as frame. Low-E double pane is the standard here. Tempered glass is required on any door near a walkway or within the safety zone. If you’re weighing the door against a bigger envelope project, our Windows & Doors in Corte Madera page covers how the openings tie into a full remodel, and our Windows & Doors service covers the wider scope.
What Sliding & Patio Doors Cost in Corte Madera, CA
Plan on $3,800 to $11,500 for a single sliding or patio door, installed, with trim and flashing. The spread is wide because five things move the number:
- Size and panel count: A standard 6-foot slider sits at the low end. An 8-foot or 12-foot multi-panel system with a lift-slide track can triple the unit cost alone.
- Existing condition: A clean opening is one price. Rotted framing, a settled header, or a sill that needs rebuilding adds framing labor and often a day.
- Structural changes: Widening an opening means a new header and engineering. That’s where a $4,000 job becomes an $8,000 one.
- Material grade: Vinyl to wood-clad is a real jump. Glass package and hardware finish add on top.
- Permit scope: Like-for-like replacements are simpler. Changing the opening size or touching the flood-zone elevation line adds review time and fees.
A written estimate from us lists the unit, the labor, the trim, the flashing, the permit, and the disposal. What it doesn’t cover, and what we flag up front, is hidden rot or structural work we can’t see until the old door is out. Those get priced separately and approved before we proceed. Our technicians have up to 12 years of experience, and on premium doors that experience matters, because a custom unit installed out of square will bind and leak no matter how good the door is.
See the difference
Before
After
Before
After
Before
AfterWhat Corte Madera Homes Specifically Do to This Job
Corte Madera sits right at the Marin split between the creek-side flats and the hillside lots above town, and that split shapes door work here more than anything else. Down in the low-lying areas near Corte Madera Creek and around the marsh edge of Town Center, openings sit in designated flood zones. A door that changes the opening often pulls in an elevation and drainage review, and the sill has to sit high enough and drain properly so a wet winter doesn’t push water at the threshold. Head up toward the hillside lots above town and the concern flips: decks and grade sit above the door, so flashing and slope drainage are what keep the frame dry.
The housing stock adds its own wrinkle. Most of the older homes are 1950s to 70s ranchers and split-levels, and we regularly see original sliders with rotted sills and headers that were never sized for a heavier modern door. The rebuild work going on across town means we’re also installing a lot of large multi-panel systems into newly framed two-story customs, where the header was engineered for it from the start. We cover Corte Madera and the surrounding areas, and homeowners often pair a patio door replacement with a Fence Repair in Corte Madera or new Paver Driveways in Corte Madera while the crew is already on site.
Serving Corte Madera, CA – Our Local Coverage Area
We serve Corte Madera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Sliding & Patio Doors in Corte Madera
A standard single door installs in one day, and a multi-panel or French door pair takes two to three days. Add two to six weeks up front for ordering and permit review. Call (866) 320-2646 for a timeline on your specific opening.
Often yes, especially if the opening size changes or the home sits in a flood zone near the creek. Like-for-like swaps are simpler, but anything that alters the opening can pull in elevation review. We handle the permit and inspection for you, and the estimate spells out the cost.
In most cases, yes. Swapping a slider into the same opening is a straight replacement. Widening it or changing the configuration is where structural work and a new header come in, and that’s priced separately once we’ve seen the framing.
Expect $3,800 to $11,500 installed for a single opening. Size, materials, existing condition, and structural changes drive the range. Call (866) 320-2646 for an exact quote, and the estimate is free.
Every install is covered by the 730-Day Done Right Promise, so if it isn’t done right, we make it right. That’s a written workmanship guarantee, not a handshake. Ask for the terms when you get your estimate.
Get a Free Sliding & Patio Doors Estimate in Corte Madera
If you’re pricing a sliding or patio door for a Corte Madera home, start with a free on-site estimate. We’ll measure the opening, check the framing and sill, talk through vinyl, fiberglass, wood-clad, and multi-panel options, and hand you a written line-item quote with no hidden costs. Calls are answered by a live person, 24/7, so call (866) 320-2646 when it’s convenient for you. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off.
Written by the team at Groundwork Construction Co.