Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Novato: What It Takes and What It Costs
A wrought or ornamental iron fence in Novato typically runs $3,500 to $9,000 for a standard residential run, and most jobs take two to four days on site once the design and permit are settled. You’re buying more than a property line: you’re buying corrosion-grade finishes that survive marine air, a gate that latches square in the Petaluma Gap wind, and posts set to hold for decades. Call (866) 320-2646 for a free on-site estimate.
How an Iron Fence Gets Built Here, Start to Finish
Iron fencing is a fabrication and mounting job, not a “dig a hole and drop a panel” job. Here’s the real sequence we run, and where your decisions land.
Stage 1: On-site measure and layout (day 1, about 2 hours)
We walk the property line, confirm where it actually sits, and check clearance to your neighbor’s structure and any existing utilities. In Novato’s tighter lots near downtown, that clearance is often the whole ballgame, so we mark setbacks before anything is ordered. You decide the run length and where the gates fall.
Stage 2: Design and spec sign-off (day 1 to 3)
You pick bar gauge, picket spacing, finish, and gate hardware. We hand you a written line-item quote with the exact spec written in, so there’s no surprise substitution later. This is the stage where a $3,500 job and a $9,000 job get separated, and it’s worth slowing down. Upfront pricing means the number you see is the number you pay.
Stage 3: Permit and HOA clearance (3 to 15 days, depends on your situation)
Where the fence is a property-line structure, a permit is usually required; interior decorative runs sometimes aren’t. If you’re in an HOA or on a WUI edge, we confirm height and material rules before fabrication starts. We pull the permit and get it inspected.
Stage 4: Fabrication and site prep (5 to 10 business days)
Your panels get fabricated to the measured spec while we set posts and prepare footings. On a retrofit over old fence, demo happens here. Original 1940s-50s concrete at Hamilton Field sometimes surfaces, and we handle the repair as part of the job rather than a change order.
Stage 5: Install, inspect, and walkthrough (1 to 2 days)
Panels mount, gates get hung and tuned, and we walk every latch and hinge with you. The final inspection gets scheduled. All of it is backed by our 730-Day Done Right Promise: if it’s not done right, we make it right, in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make
Iron fence isn’t one product. Here’s where the trade-offs live.
- Wrought iron vs. steel vs. aluminum: Wrought iron is the heaviest and most durable, but it also costs the most. Steel is a close second with a painted finish. Aluminum is the lightest and most corrosion-resistant, and it suits coastal air, but it dents more easily under impact. For Novato’s wind corridor, weight matters.
- Bar gauge: 14-gauge is standard; 12-gauge adds rigidity and cost. On exposed ridgeline lots, we lean heavier.
- Finish: Powder coat holds up better in salt air than paint. A galvanized core under powder coat is the coastal-grade call, and it’s what we recommend near Ignacio and Hamilton.
- Picket spacing: Tighter spacing is more secure for pets and small children; wider spacing is lighter and cheaper.
- Gate hardware: Self-closing hinges and a keyed latch are standard; a crash bar or auto-opener adds cost and a power run.
- Post mounting: Set in concrete footings for property-line work; surface-mounted on existing hardscape for decorative runs.
What Iron Fence Costs in Novato, CA
Residential iron fencing in Novato lands in the $3,500 to $9,000 range for most jobs. Here’s what moves it up or down.
| Line item | Typical range |
|---|---|
| Standard iron run, 40-60 linear feet | $3,500 – $6,000 |
| Heavier-gauge or decorative run | $6,000 – $9,000 |
| Gate and hardware | $600 – $1,800 |
| Permit and inspection | $250 – $700 |
| Old fence removal | $300 – $800 |
The variables that push a job toward the high end: longer runs, heavier bar gauge, powder-coat over a galvanized core, more gates, and site access. On Novato’s tighter lots, getting material to the back line sometimes means more labor than the fence itself. A written estimate lists every line item; it excludes anything we can’t see until demo, and we tell you that up front so there are no surprises.
See the difference
Before
After
Before
After
Before
AfterWhat Novato Homes Specifically Do to This Job
Novato sits at the Marin-Sonoma line where the fog belt gives way to hotter inland valleys. That means marine air along the 101 corridor toward Ignacio and Hamilton eats at painted steel, and the wildfire-hardened assembly rules near the WUI edges toward Petaluma Hill and above downtown push homeowners toward noncombustible iron over wood. The Petaluma Gap wind funnel is the other factor: fences and gate hardware here fail from wind loading more than in neighboring towns, so we spec heavier hinges and set posts deeper. Hamilton Field’s 1940s-50s military duplexes were never built with modern shear, so a “simple” fence retrofit there sometimes surfaces old concrete and outdated stucco. If you’re pairing this with hardscape, homeowners often pair an iron fence with our Patios, Walkways & Pool Decks in Novato, and for larger lot work the ADU Design & Permitting in Novato scope often comes up in the same plan. We cover all of Novato, from the 94945 and 94949 ZIPs to 94948 and 94998.
If the fence is part of a wider project, see our Fence Installation in Novato page for the full scope. Otherwise, this Fence Installation work is what we do.
Serving Novato, CA – Our Local Coverage Area
We serve Novato and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Novato
Most Novato iron fence jobs take two to four days on site once fabrication is done, with one to three weeks of lead time before that for permit and fabrication. Call (866) 320-2646 for a firm timeline on your specific lot.
Property-line iron fences usually require a permit; decorative interior runs sometimes don’t. We pull the permit and schedule the inspection as part of the job. Call (866) 320-2646 and we’ll tell you exactly what your address needs.
Yes, in nearly every case. Iron fencing mounts to posts set in footings, so it doesn’t move plumbing, wiring, or structure. The only exception is gate automation, which needs a power run. Call (866) 320-2646 to confirm on your property.
Most residential iron fence jobs in Novato run $3,500 to $9,000, with heavier gauge, more gates, and coastal-grade finish pushing toward the top. Call (866) 320-2646 for an exact written quote; estimates are free.
Every iron fence we install is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. Call (866) 320-2646 to go over what’s covered before work starts.
Get a Free Iron Fence Estimate in Novato
Call (866) 320-2646 to schedule a free on-site estimate for your iron fence in Novato. A real person answers around the clock, and we’ll walk the property line, talk through gauge and finish, and hand you a written line-item quote with no obligation. If your project qualifies, $1,000 off over $10,000 and 0% financing for 18 months are available.
Written by the team at Groundwork Construction Co.