Last updated November 17, 2026
Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Driveway & Pavers Troubleshooting: Common Problems and How to Fix Them
Here’s the counterintuitive part: the paver that’s sinking in your driveway is almost never the problem. It’s the messenger. A sunken section, a crack that runs in a straight line, a wave in the field where there used to be flat – those are symptoms of what’s happening in the layers underneath, where the base, the bedding sand, and the soil under everything are quietly failing. Homeowners who patch the top and ignore the bottom usually spend twice, and the second failure often arrives faster than the first. In this guide we’ll show you how to read what your San Francisco driveway is actually telling you, from base compaction failure to clay-soil drainage, so you can fix the cause instead of chasing the symptom.
Quick Answer
Most visible paver problems – sinking, cracking, shifting, rocking – trace back to one of four root causes: a base that wasn’t compacted properly, bedding sand that has washed out, subgrade soil that’s eroding, or edge restraint that has failed. Fix the surface without fixing the cause and the same failure returns. The right repair depends entirely on which of those four you’re actually dealing with, and the pattern of displacement is how you tell them apart.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Table of Contents
- How to Read the Pattern of Displacement
- Base Compaction Failure: The Sinking Section
- Bedding Sand Washout: The Wavy Field
- Subgrade Erosion: The Collapsing Corner
- Edge Restraint Failure: The Root Cause You Can Spot First
- San Francisco Drainage: Why Clay Soil Pushes Pavers Up From Below
- Spot Fix vs. Full Section Pull: What’s Genuinely Repairable
- How to Document Paver Problems to Protect Yourself
How to Read the Pattern of Displacement
Before you touch anything, walk your driveway slowly and look at the shape of the failure, not just its location. The geometry of displacement is a diagnostic tool. Different root causes push pavers in different directions and cluster them in different patterns, and once you know what to look for, you can usually name the cause from the sidewalk.
Three patterns cover the vast majority of what we see in San Francisco:
- The local bowl or dip. One area settles 1/2″ to 2″ lower than the surrounding field, and the pavers around it stay tight. This points to base compaction failure or a soft spot in the subgrade directly under that section. The failure is vertical and localized.
- The wave or ridge running across the field. Pavers lift and dip in a rolling pattern, often along a joint line or the direction of slope. This is usually bedding sand that has migrated or washed out, leaving some pavers supported and others unsupported. It can also signal hydrostatic pressure from below in clay-heavy soil.
- The widening gap at the edge. Joints open up progressively toward the driveway’s perimeter, and pavers nearest the edge rock or shift when you step on them. Nine times out of ten this is edge restraint failure, and it’s the single most common root cause of widespread paver movement.
In our experience in San Francisco, most driveways that come to us with “sinking pavers” have two patterns at once – an edge failure at the perimeter and a secondary dip where water got in through the opened joints. Treat only the dip and you’ll be back within a season. The edge is what fed the dip.
Base Compaction Failure: The Sinking Section
A section that has settled into a smooth, localized bowl is the classic sign that the aggregate base beneath the pavers wasn’t compacted in lifts, or was installed over soft subgrade. Paver base isn’t a single dump-and-tamp job. It has to go down in layers – typically 2″ to 4″ lifts – with each lift compacted with a plate compactor before the next is added. Skip that process, or compact a thick lift only at the top, and the base looks solid on installation day and settles over the next two or three wet seasons.
San Francisco’s climate compounds this. Our rainy season pushes water into the base, and a base that’s a few percentage points below optimum moisture content during compaction will never reach the density it should. The pavers sit on a sponge that looks like concrete.
How to confirm base failure rather than a sand issue:
- Pull two or three pavers from the center of the dip and set them aside carefully.
- Look at the bedding sand layer. If the sand is intact and roughly uniform under the settled pavers, the failure is below the sand, in the base.
- Probe the base with a screwdriver or a stiff rod. If it gives more than an inch under firm hand pressure, the base is loose.
- Check the depth. A proper base is typically 4″ to 6″ compacted for a residential driveway, more over poor subgrade.
A spot fix on a base failure means pulling the settled section back to solid ground, re-compacting in lifts, and resetting the pavers on fresh bedding. It doesn’t mean pouring sand into the dip. Sand filler buys you a few weeks and makes the next failure worse.
Bedding Sand Washout: The Wavy Field
Bedding sand is the roughly 1″ layer between the compacted base and the pavers. Its job is to let the pavers seat uniformly and to absorb minor movement. What it can’t do is survive water running through it. When joints open, water gets under the pavers, and that water takes bedding sand with it – sometimes slowly, sometimes in one big storm. The result is a wavy field where some pavers are supported and others are hanging in a void.
This pattern is different from base failure. With sand washout, the pavers themselves aren’t so much sinking as the whole surface is losing consistent support. You’ll see it as:
- Pavers that rock underfoot but haven’t dropped noticeably.
- A rolling or wavy high-low pattern, often worse in the direction water drains.
- Widened joints along the run where water moves fastest.
- Sand visible in the joints, or washed out onto the sidewalk after a storm.
The way to tell sand washout from base failure is that the pavers themselves are usually flat and intact – they’re just not sitting on anything. Reset a section of a washout and the paver comes up with a clean bottom and a hollow underneath. Reset a base failure and the paver lifts with sand stuck to it, and the base underneath is soft.
The fix for a true washout is a section pull – lift the pavers, clean them, re-screed fresh bedding sand over a confirmed-solid base, reset, and re-sand the joints. Then fix whatever opened the joints in the first place, which is usually the edge. We see this constantly in San Francisco neighborhoods with older driveways near mature street trees, where the roots have lifted the edge and opened the whole field to water.
Subgrade Erosion: The Collapsing Corner
Subgrade is the natural soil under the base. When it erodes, the whole pavement structure above it collapses into the void, and that’s a different repair category entirely. Subgrade erosion shows up as a corner or edge section dropping sharply – often 2″ or more – with the pavers around it still tight and the joints intact. It can also show as a soft spot in the field where stepping on the pavers makes the ground under them move.
Common causes in San Francisco:
- Poor surface drainage pushing water along the base course. Water that enters at the edge and can’t escape travels under the pavement, eroding soil as it goes.
- Downspouts and gutter discharge. A downspout aimed at the driveway edge is a slow-motion erosion machine.
- Utility trench settling. Old trenches for water, sewer, or gas lines compact differently than surrounding soil, and the trench line often settles years later.
- Clay soil that doesn’t percolate. San Francisco’s expansive clay can hold water against the subgrade, softening it indefinitely.
Erosion is not a spot fix. You have to open the section wide enough to find the eroded void, fill and compact it properly, and – critically – correct whatever was sending water there. Fill a void without redirecting the water and you’ll be back on the same phone call within a year or two. That’s one of the reasons we treat drainage correction as part of the driveway scope, not a separate conversation.
Edge Restraint Failure: The Root Cause You Can Spot First
If we could teach homeowners to check exactly one thing on a paver driveway, it would be the edge. Edge restraint is the border – usually a concrete curb, aluminum edge, or plastic restraint pinned into the ground – that holds the perimeter pavers from spreading outward. When it fails, the field above loses its compression. Pavers creep outward, joints open, water gets in, and every other problem this guide covers starts rolling downhill from there.
Edge restraint failure is the single most common root cause of widespread paver movement we see, and it’s the cheapest thing to fix early and the most expensive thing to fix late.
Check your edge in five minutes:
- Walk the entire perimeter of the driveway. Look for a curb or restraint that has separated from the pavers, tilted outward, or cracked.
- Press on the perimeter pavers with your foot. If they rock or shift outward, the restraint is loose.
- Look for a widened joint line – 3/8″ or more – running parallel to the edge.
- Check the pins. Aluminum and plastic restraints are held by spikes; if they’re rusted through or pulled up, the restraint will move under load.
- Check the transition to grass or planting beds. Restraint buried in soft soil is more likely to fail than restraint pinned into a hard border.
In San Francisco, edge failure is especially common on driveways that meet a planting strip or a steep grade change, where the soil behind the edge stays wet through the rainy season. A concrete edge curb that sits on a properly compacted base will outlast the driveway; an aluminum edge pinned into loose clay is a 10-year component at best.
San Francisco Drainage: Why Clay Soil Pushes Pavers Up From Below
San Francisco sits on top of serious clay in many neighborhoods, and clay behaves nothing like the sandy soils paver installation guides seem to assume. Clay doesn’t percolate. Water that gets into the ground under your driveway can’t drain down, so it sits, saturates the clay, and creates hydrostatic pressure against the underside of the pavement structure.
Hydrostatic pressure is a force pushing up. When the clay below a driveway can’t shed water, that pressure has to go somewhere, and what it does in a paver field is lift pavers – sometimes as a ridge or hump in the field, sometimes by pumping water up through the joints during heavy rain and leaving a tell-tale fan of sand on the surface afterward.
The specific patterns of clay-driven failure in San Francisco:
- Heave ridges running away from the house. Hydrostatic pressure lifting the field in a straight-ish line perpendicular to the slope, especially on driveways graded toward the garage.
- Sand pumping after storms. Visible sand in the joints or on the surface after rain tells you water is moving below the pavers.
- Softness in spring that stiffens in summer. A driveway that feels vaguely spongy in March and firms up by July is a symptom of seasonal clay saturation, not compaction failure.
- Ponding at the low point. If the low point of your driveway holds water for more than a day after rain, water is also sitting under it.
Fixing clay-driven heave is a drainage problem, not a paving problem. The right scope usually involves correcting the surface slope and, where the driveway meets a slope or a neighboring property, adding subsurface drainage to give water somewhere to go. Belgard makes a range of permeable paver systems we install for San Francisco properties where managing surface water matters as much as the look of the driveway. Any qualified installer in San Francisco needs to talk about drainage load and clay behavior on your specific lot, not just slope percentages.
Spot Fix vs. Full Section Pull: What’s Genuinely Repairable
Not every paver problem is a full replacement, and not every problem can be spot fixed. Knowing which category your failure falls into saves you from both overpaying and under-fixing.
Genuinely repairable with a targeted section pull:
- One settled section with a clearly identifiable cause and solid pavers around it.
- Bedding sand washout over a base that is confirmed to be sound.
- Edge restraint failure on a field that hasn’t yet spread at the joints.
- A localized low spot where the pavers are intact and the joints are tight.
Requires full section pull to do correctly, even if the visible damage is small:
- Subgrade erosion. You have to open the section back far enough to find the actual void, and voids travel further than the dip shows.
- Any repair where the pavers on either side are already rocking – the failure has spread.
- Repairs where the base is trending soft across the whole section, not just at the dip.
- Any driveway where the edge has been failing for several years. The joints at the perimeter will be wide enough that resetting pavers without correcting the joint geometry will leave the new section as the weak point.
There’s also a category of repair we simply don’t recommend: pouring a concrete patch into a paver field. It never bonds properly, it doesn’t move with the pavers, and it makes the next repair cost more. Every time. For anyone dealing with a large-scale failure that’s starting to reach a garage apron, we’ll sometimes walk the homeowner through whether the driveway is now an anchor problem for a bigger project – see our guide to Home Additions & ADU in San Francisco for the way a failed driveway often overlaps with an addition plan.
How to Document Paver Problems to Protect Yourself
If you’re going to file a warranty claim – with a contractor, with a manufacturer, or with a successor company – the paper trail matters more than the argument. Homeowners with good documentation get repairs made. Homeowners without it get told the damage “isn’t covered” or “was caused by improper use.”
Here’s how to document a paver problem properly:
- Take wide shots first, then close-ups. Once a year, walk the driveway and take one wide photo of each side, including the garage, sidewalk, and street edge. Six shots, one minute, every spring.
- Photograph the pattern, not just the worst paver. Frame each failure so the pattern is visible – the widening edge joint, the wave across the field, the outline of the dip. Photos of one paver tell no story.
- Include a reference object for scale. A tape measure laid across the dip or across the open joint gives the photo meaning years later.
- Log the date, the weather, and what you observed. A spreadsheet with three columns (date, condition, notes) is more persuasive than any single photo. Note the first day you saw the problem – that timing often proves the failure was outside a workmanship window.
- Photograph water behavior after a storm. Where the water went, where it pooled, where the sand came out of the joints. Drainage disputes turn on these photos.
- Keep the original contract and the written scope. If the file says “compact base in 4-inch lifts” and the base is loose in the dip, you have a factual case. Photograph the opened section yourself when the repair is underway – pavers lifted, base exposed. That’s the photo that wins the claim.
One thing that makes documentation easier on the front end: a workmanship guarantee you can point to in writing, with a duration stated in the contract. The Groundwork Construction Co. of San Francisco home page lays out our 730-Day Done Right Promise, which is one of the longest workmanship guarantees in the residential construction space – if it’s not done right, we make it right. When you’re comparing estimates, ask every contractor what their written warranty says about paver settlement, and ask for it in the scope document, not the marketing brochure.
Common Mistakes to Avoid
- Filling a dip with sand or stone dust. It disappears into the joints, doesn’t fix the base, and hides the failure until it gets worse. In a San Francisco rainy season, it always gets worse.
- Skipping the edge check because the middle looks fine. The edge is where problems start. Five minutes walking the perimeter before you call anyone will save you from being oversold a full replacement for an edge restraint fix.
- Treating a drainage problem as a paving problem. If water is sitting on or under your driveway in a clay-heavy neighborhood, any repair that doesn’t correct the slope or add drainage will fail again.
- Letting a contractor open the surface without photographing the base. The base is the evidence. Once fresh pavers are back down, the fact of a loose base is gone. Photograph the opened section yourself before it’s re-covered.
- Assuming “resealing” fixes movement. Sealer protects surface finish. It does nothing for sinking, rocking, or shifting, and some sealers actually trap moisture at the joint line in a wet climate. If a paver problem is structural, sealing it is cosmetic.
- Waiting until the field spreads to make the call. A single dipping section with tight joints is a $400 to $900 repair. By the time the whole perimeter has opened joints and the pavers rock across the field, you’re looking at a section pull or full replacement.
- Not asking about the base depth in the bid. A paver driveway bid that says “compact base” without a depth is a bid that’s going to fail. Ask for 4″ to 6″ of compacted base minimum over soil, more on clay.
One more: don’t assume the failure is your fault for the way you use the driveway. Pavers are engineered for vehicle loads. If they’re failing under normal use, the cause is almost always installation, base, drainage, or edge – and the fixes above are how you prove which.
See the difference
Before
After
Before
After
Before
AfterWhen to Call a Professional
Some repairs are within reach of a confident homeowner – resetting a single paver, replacing a failed edge spike, re-sanding joints after a storm. Anything involving the base, the subgrade, or drainage correction is a different category. Opening a driveway section and rebuilding the base is heavy, dusty work that depends on proper compaction in lifts, and the failure mode of a bad DIY rebuild is that the same dip returns the next rainy season – only now you’ve spent the material cost twice.
Call a professional when: the visible dip is more than one paver wide, the edge restraint is loose or cracked, subgrade erosion is suspected, water is pumping up through the joints after storms, or the field is rocking anywhere except one isolated paver. Those are all scenarios where the repair depends on getting the layers underneath right, and where a documented workmanship guarantee actually matters.
Groundwork Construction Co. of San Francisco offers free estimates in San Francisco – call (866) 320-2646. Our technicians have up to 12 years of experience with paver installation and repair, and every project is backed by our 730-Day Done Right Promise. Calls are answered by a live person, 24/7, and we arrive in uniform with background-checked technicians.
If your driveway work connects to fencing along the property line, our guide to Fence Installation in San Francisco covers the same base-and-edge principles for wood and composite fence footings – the failure modes are the same, just vertical instead of horizontal.
Frequently Asked Questions
Most localized paver driveway repairs in San Francisco run between $400 and $1,500 for a spot fix, and $3,000 to $9,000 for a section pull that involves re-compacting the base and re-establishing the edge. Full driveway replacement is a separate category and depends on square footage, drainage corrections, and paver selection. Call (866) 320-2646 for an exact quote – estimates are free and we’ll tell you which category your repair falls into.
A single localized dip almost always means the base under that section wasn’t compacted in proper lifts, or the subgrade there was softer than the surrounding soil – often a utility trench or a buried root zone. The pavers themselves are fine. The fix is to open the section, re-compact the base in lifts, and reset. Filling the dip with sand is not a fix; it’s a delay tactic.
Water is reaching the bedding sand or the base, which means the joints are open somewhere. In San Francisco, that somewhere is usually the edge. Check the perimeter joints for widening and check the edge restraint for separation before you assume the whole field has to come up. Moving pavers after rain is a drainage and edge joint problem, not a “these pavers are bad” problem.
No. A single sunken section is not urgent, and it usually stays stable for months. The concerns are trip hazards, water pooling, and the fact that open joints let the failure spread. If the sunken section is at a step, on a slope, or near a garage threshold, don’t wait – call for a look. Otherwise, schedule the repair within the next few months and it’ll cost less than a delayed one.
Not with our written, line-item upfront pricing. When we open a section and find a deeper problem than the surface suggested – like subgrade erosion under what looked like a base failure – we stop, show you what we found with photos, and quote the correction in writing before proceeding. The number you see is the number you pay for the scope we agreed to. Call (866) 320-2646 to schedule the estimate.
Most paver repairs and like-for-like driveway replacements don’t require a permit. Anything that changes the driveway’s footprint, increases impervious surface, alters drainage or grading, or affects the connection to the public right-of-way does, and the scope of that permit depends on your lot and the block. We tell you at the estimate which category your project falls into and pull and pass the permits we need. For bigger scopes, see our Driveway & Pavers in San Francisco page. Call (866) 320-2646 for a free estimate.
The Bottom Line
When you’re standing on your driveway staring at a sinking paver, the useful question isn’t “which paver needs to come up” – it’s “what underneath is failing.” Read the pattern of displacement: a localized bowl points to base compaction, a wave points to sand washout, a hard drop at the corner points to subgrade erosion, and a widening edge joint points to edge restraint failure. San Francisco’s clay soil makes all four worse by trapping water under the driveway, so drainage belongs in almost every repair conversation. Document the failure properly before anyone opens the surface, fix the cause the first time, and ask any contractor for their workmanship guarantee in writing. Do that, and the repair you pay for is the only one you pay for.
Call (866) 320-2646 to schedule your free estimate with Groundwork Construction Co. of San Francisco. We’ll walk the driveway with you, open what needs to be opened, and tell you plainly what’s failing and what it costs – upfront, in writing, with 0% financing for 18 months and $1,000 off projects over $10,000 available.
Written by the team at Groundwork Construction Co. of San Francisco.