Last updated November 17, 2026
Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Windows & Doors Troubleshooting: Common Problems and How to Fix Them
A door that suddenly sticks in winter isn’t a door problem. It’s almost always a foundation or framing problem that your door is measuring for you. Fix the door and you’ve missed the message. We’ve walked into San Francisco homes where a homeowner had planed the same door edge three winters running, and the real culprit was a settling pier under the entry that had been moving for a decade. Windows and doors are the most honest reporters in your house. This guide teaches you to read what they’re saying: how to trace a symptom back to its root cause, tell product failure from installation failure from structural signal, and know which fixes you can handle yourself without voiding a warranty or hiding a bill that’s coming in twelve months.
Quick Answer
Most window and door problems fall into five predictable categories: drafts, sticking or binding, fogged glass, water intrusion, and hardware failure. The fix depends entirely on the root cause, which is usually one of three things: a failed product (seal, gasket, hardware), a bad installation (gaps, missing flashing, no shimming), or a structural movement the window or door is reacting to. Treat the symptom without diagnosing the cause and you’ll pay for the same repair again within a year. In San Francisco, fogged double-pane glass is the single most common complaint we see, and it nearly always signals a failed perimeter seal rather than a cleaning problem.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Table of Contents
- The Symptom-to-Cause Diagnostic Tree
- Product Failure vs. Installation Failure vs. Structural Signal
- Drafts and Cold Air: Where They Come From and What They Mean
- Sticking Doors and Windows: Reading the Message
- Fogged Glass and San Francisco’s Fog-Season Condensation Problem
- Water Intrusion: The Flashing and Seal Story
- Hardware Failure: What Wears Out First and Why
- What a Homeowner Can Safely Check Before Calling Anyone
- When a Quick Fix Is Legitimate and When It’s Masking a Bigger Bill
The Symptom-to-Cause Diagnostic Tree
Every window and door problem you’ll ever face starts as a symptom. Your job is to trace it back to the cause. Here’s the diagnostic tree we use on every call, mapped symptom to likely root cause:
- Draft around the frame or sash: usually a failed weatherstripping, worn gasket, or missing shim behind the jamb. Less often, it’s gaps in the rough opening from an installation that skipped spray foam and sealant.
- Sticking, binding, or rubbing: usually structural movement – foundation settling, framing movement, or a sagging header. Sometimes it’s a swollen wood product in a wet season or failed hinges.
- Fogged or cloudy double-pane glass: a failed seal at the edge of the insulated glass unit (IGU). Moisture is inside the glass, not on it. The window isn’t broken; the seal is.
- Water intrusion at the sill, jamb, or head: failed flashing, a missing head flashing, degraded sealant, or a sill that was never properly pitched to drain.
- Hardware failure (cranks, locks, rollers, hinges): normal wear, but accelerated by salt air on the coast and by hardware spec’d for the wrong exposure level.
Run the tree before you call anyone. In our experience, homeowners skip this step and call a window company when they needed a foundation assessment, or call a general contractor when the real problem was a $40 crank mechanism on a casement window in the Outer Sunset. The right diagnosis saves you weeks and redirects money to the actual problem.
Product Failure vs. Installation Failure vs. Structural Signal
This is the single most important distinction in window and door troubleshooting, because the fix and the responsible party are completely different in each case.
Product failure is the window or door itself breaking down: a seal fail on the glass, a hinge that shears, a lock that stops engaging. Product failures are usually covered by the manufacturer’s warranty, and if the product is under ten years old, that’s the first call. Installation failure is the contractor’s work: missing flashing, no shims under the sill, fasteners that weren’t corrosion-rated for the coast, rough openings cut too wide or too narrow. These typically show up in the first 18 months and are the installer’s responsibility. Structural signal is neither of those. The window or door isn’t failing; it’s telling you the house moved, and the product is an unwilling witness. Foundation settling, a compromised header, or a wall that’s rotating all show up as sticking doors and cracked glass.
- Check timing. A problem that appeared gradually over years is more likely structural or wear. A problem that appeared suddenly after a rain event or a shove is a product or installation issue.
- Check location. Is the problem on one unit or many? One window fogging is a product fail. Every window on a south wall showing water intrusion points to a cladding or installation issue.
- Check the walls around it. Look for cracks in drywall at the corners of the opening, doors that have started sticking in the same room, or a floor that’s gone off-level. Any of those tilt the diagnosis toward structural.
- Check the paperwork. If you have the original install invoice, look at the fastener spec and the flashing detail. Cheap fasteners on a coastal install explain more hardware failures than any other single factor.
San Francisco’s housing stock makes this distinction especially important. Two-thirds of the city’s homes were built before 1960, and a large share of the pre-war stock sits on unbraced cripple walls or raised foundations that have been moving for decades. A door that binds in one neighborhood may be a hinge problem; in another, it’s the foundation. We see the difference play out across the city – and it’s why a foundation-to-finish-line approach beats a window-only contractor who arrives with a checklist. If you’re considering a bigger project like a Home Additions & ADU in San Francisco, the same window and door diagnostics apply because the envelope is where movement shows up first.
Drafts and Cold Air: Where They Come From and What They Mean
A draft isn’t just an inconvenience. It’s a measurable energy loss and a signal about the envelope. In San Francisco, where fog and wind pull cold air off the Pacific most of the year, a drafty window costs more in heating and comfort than the same window would in a drier climate. Before you blame the window, trace the source:
- Around the sash (between sash and frame): worn weatherstripping or a gasket that’s compressed flat. This is a maintenance fix and usually straightforward.
- Around the frame (between frame and wall): an installation gap. This is a retrofit caulk and spray-foam issue and needs to be done properly with backer rod and a sealant rated for the substrate.
- Under the door or at the threshold: a misaligned threshold, a worn sweep, or an out-of-level sill. The door may also be reporting a settling foundation.
- Through the lock or hardware: rare, but worn hardware can leave daylight visible and air moving.
Here’s the check we recommend before you call anyone: on a windy day, close the window or door and pass a lit incense stick or a tissue around the perimeter. Where the smoke or tissue moves, you’ve found the leak. That tells a contractor exactly where to look and saves a diagnostic visit. If the draft is at the frame-to-wall joint on multiple units in the same windward room, that’s an installation-pattern problem and it needs a real repair, not more caulk over the top of old caulk.
Sticking Doors and Windows: Reading the Message
Sticking is the loudest symptom in window and door troubleshooting and the one homeowners most often misread. When a door sticks, it’s telling you something moved. Your job is to figure out what.
A door that sticks only in winter and frees up in summer is almost always seasonal wood movement or a small foundation shift that’s tied to soil moisture. A door that sticks on one corner only, with a visible gap at the opposite top corner, has rotated – the hinge side has moved relative to the strike side. A window that won’t close has a different story: a sash that’s out of square, a failed balance mechanism, or a frame that’s gone out of plumb.
- Mark the rub. Put a strip of painter’s tape on the jamb and close the door. The scuff marks pinpoint the contact point.
- Check the reveal. Look at the gap between the door and the jamb at the top, sides, and bottom. An even reveal is a hinge or seal problem. An uneven reveal is a movement problem.
- Check the floor and ceiling around the opening. Cracks radiating from the corners of a door frame, or a ceiling that’s gone out of level, tilt the diagnosis toward structural.
- Check for plumbing or drainage nearby. In San Francisco’s older homes, a slow drain leak or a foundation with poor drainage is a common cause of movement at a nearby opening.
If the reveal is even and the rub is local, a hinge adjustment or a small plane is the correct fix. If the reveal is uneven, stop. Call a contractor who can evaluate the whole opening and the structure behind it. Planing is a legitimate repair for a swollen wood door once a year; doing it every winter is a sign you’re treating a structural signal as a maintenance item. The fix you skip in year one shows up as a bigger bill in year three.
Fogged Glass and San Francisco’s Fog-Season Condensation Problem
Fogged double-pane glass is the most common window complaint in San Francisco, and it’s almost always misdiagnosed. The fog is not condensation on the inside of the room. It’s moisture that has worked its way between the two panes because the perimeter seal on the insulated glass unit has failed. Once that seal goes, the desiccant in the spacer is saturated, moisture gets in, and the glass is permanently cloudy. Wiping won’t reach it because the water is inside the unit.
Coastal conditions matter. The salt air, the fog, the temperature swings between a cold morning and a warm afternoon all put more stress on IGU seals than a drier inland climate does. The typical lifespan of a well-built double-pane seal in San Francisco conditions is roughly 10 to 15 years, and we see many fail earlier – sometimes as early as year eight in the fog belt neighborhoods like the Sunset and Richmond districts. When a seal fails, the fix is to replace the IGU (the glass unit) or the whole window, not to try to clean or dry the glass.
- Fog between the panes: failed seal. Replace the IGU or the unit; the gas fill and low-E coating are gone with it.
- Fog on the interior surface only: a humidity problem inside the home, not a window problem. Address ventilation.
- Etching or a white haze that won’t wipe off: long-term moisture exposure on the glass surface; the IGU needs replacement.
We’ve found that homeowners in the fog belt often tolerate fogged glass for years because it feels cosmetic. It’s not. A failed IGU loses most of its insulating value, which means higher energy bills and a visible deficiency the next time you sell. If you’re already planning a window and door replacement as part of a larger project, the Groundwork Construction Co. of San Francisco home team can scope it as part of a whole-envelope update. When it’s time to look at a full replacement with Andersen or Marvin units, that’s the moment to compare the IGU warranty terms side by side before you commit.
Water Intrusion: The Flashing and Seal Story
Water intrusion is the most expensive window and door problem to ignore, and it’s almost always an installation or flashing failure rather than a product defect. Water comes in where it was allowed to get behind the window or door and had nowhere to drain. The exterior is a layered system: cladding, weather barrier, flashing, the window or door unit, and the interior trim. If any layer of that system is wrong, water finds the weak point.
- Water at the sill: a sill that wasn’t pitched to drain, missing sill pan flashing, or a failed seal at the sill-to-wall joint.
- Water at the head: missing or backward-lapped head flashing. The head flashing must shed water over the cladding below, not behind it.
- Water at the jambs: gaps in the frame-to-wall sealant, or a weather barrier that wasn’t lapped shingle-style.
- Water in the wall cavity: the worst case and the most likely to require opening up the wall to repair.
In San Francisco, wind-driven rain against the seaward and west-facing walls is the recurring test. We’ve seen windows in the Avenues and the Marina that held up fine for years until a storm drove rain at a low angle and found a seam that was never flashed correctly. That’s a repeatable installation failure, not bad luck. If you’re having a window replaced and the contractor doesn’t talk to you about flashing, ask. It’s the difference between a dry window and a wall repair eight years later. And if you’re already hiring for exterior work, it’s worth reading our guide to Fence Installation in San Francisco, because exterior sequencing and weather protection matter across all the trades.
Hardware Failure: What Wears Out First and Why
Hardware fails, and it fails in a predictable order. Cranks on casement and awning windows are the first to go, typically after 8 to 12 years of regular use. Hinges on doors, especially heavier entry doors, wear at the top where the load sits. Rollers on sliding doors and windows seize or flatten. Locks and latches loosen, and multipoint locking systems can get out of alignment when the door shifts in its frame.
Coastal salt air matters more than most homeowners realize. Hardware spec’d for an interior exposure will pit and corrode within a few years on a seaward-facing window in the Sunset or the Presidio. The fix isn’t just to replace the part; it’s to replace it with hardware rated for coastal exposure. Stainless or marine-grade hardware costs a bit more and lasts considerably longer.
- Match the part. Match the manufacturer and model, not just the appearance. An off-brand crank often won’t fit the operator spline and will strip within a season.
- Check the alignment. For a lock that won’t engage, check the door reveal first. If the door has moved, the lock is fine and the frame isn’t.
- Check the finish. Pitting, white corrosion, or a flaky surface on hardware indicates the coastal exposure rating is inadequate. Replace with a rated part.
- Test the whole system. After replacing a component, open, close, and lock the unit several times to confirm nothing is binding.
Hardware is the cheapest window and door repair you’ll ever make, and it’s the one homeowners most often skip because it feels cosmetic. A seized roller on a sliding door scratches the track and then the door, and a $30 part becomes a $900 door. Keep it simple: fix hardware when it fails, use the right part, and keep the tracks clean.
What a Homeowner Can Safely Check Before Calling Anyone
There’s a short list of checks you can safely do yourself without voiding a warranty or making a problem worse. Here they are, in the order we recommend:
- Paper and pencil. Note where and when the symptom appears – room, wall, time of day, weather. Patterns are the diagnosis.
- The tissue and incense test. Find drafts at the perimeter on a windy day. Mark the leak points with painter’s tape.
- The reveal check. Look at the gap around a sticking door or window. Even gap equals a hardware or seal problem; uneven gap equals movement.
- The flashlight check. Look for cracks in the drywall at the corners of the opening, in the ceiling, and at the floor near the unit.
- The glass check. Note whether the fog is between the panes (seal failure) or only on the inside surface (humidity). Take a phone photo; it’s faster than describing it later.
- The exterior visual check. From the ground, look for cracked sealant, missing flashing, or a sill that holds water. Don’t climb a ladder; look from a safe angle and photograph anything suspicious.
What you should not do: disassemble the window, attempt to drill the IGU to drain it, plane a sticking door before you’ve checked the reveal, or reseal an exterior joint without removing the old sealant first. Those moves void warranties and hide problems.
When a Quick Fix Is Legitimate and When It’s Masking a Bigger Bill
Some quick fixes are exactly right. Others are putting a bandage on a crack in the foundation. Here’s the line we draw in our own work.
Legitimate quick fixes:
- Replacing worn weatherstripping around the sash. It’s a wear item, not a failure.
- Adjusting a hinge on a door with an even reveal. The door is fine; the hinge is tired.
- Repointing a single exterior sealant joint that’s cracked after ten years. Sealant is a wear item too.
- Cleaning sliding door tracks and rollers. Routine maintenance.
- Tightening or replacing a screw on a loose strike plate.
Masking fixes that will cost more in 12 months:
- Smearing more caulk over the top of old cracked caulk. The old sealant fails underneath and the new bead peels off in a season.
- Planing a door edge for the second or third winter in a row. The door is telling you the structure moved. Stop cutting and start diagnosing.
- Drilling a fogged IGU to drain the moisture. It doesn’t work, it voids the unit warranty, and it makes the visible fog worse.
- Adding a bead of sealant at the exterior sill without addressing the flashing behind it. Water still gets in; now it can’t get out.
- Shimming a window frame to make it close without checking whether the frame is plumb.
We’ve seen the second list cost homeowners thousands twice: once for the bandage and again for the real repair. A 730-Day Done Right Promise exists in our business specifically because we don’t want to be the contractor who did the bandage. If a repair isn’t done right, we make it right, and we write that down.
Common Mistakes to Avoid
- Blaming the window when the door is the witness. If the door and the window on the same wall both started sticking in the same season, one of them is a symptom. Diagnose the wall, not the product.
- Calling a window company first. A window company sells windows. Call a contractor who can assess the whole opening and the structure behind it before anyone quotes you a replacement. In San Francisco, that difference is a lot of money.
- Ignoring fogged glass because it “still looks fine from the street.” A failed IGU loses its insulating value and its low-E coating. In the fog belt, that’s a real energy and resale problem.
- Resealing water intrusion without fixing the flashing. Sealant is the last line of defense, not the first. If the flashing is wrong, more sealant just traps water inside the wall.
- Using interior-rated hardware on a seaward-facing window. Salt air will eat it. Match the exposure rating to the wall it’s on.
- Treating a sticking door as a door problem every winter. Planing the same edge three years in a row is a signal the foundation is moving. The fix you skip gets more expensive.
- Doing the repair without documenting the diagnosis. Photos of the reveal, the fog, and the leak points make the eventual repair faster, cheaper, and easier to argue if a warranty claim comes up.
See the difference
Before
After
Before
After
Before
AfterWhen to Call a Professional
Call a professional when the reveal is uneven, when water is entering the wall cavity, when the glass is fogged between the panes, when the same door has started sticking repeatedly across seasons, or when hardware has failed on a unit that’s still under warranty (the warranty terms usually require professional service). Call immediately if you see soft or discolored drywall around an opening, which means water has been inside the wall long enough to do damage. And call if you’re planning a larger exterior project: windows and doors interface with Driveway & Pavers in San Francisco and exterior drainage in ways that are cheaper to plan together than to fix separately.
Groundwork Construction Co. of San Francisco offers free estimates in San Francisco – call (866) 320-2646. Calls are answered by a live person 24/7, so you’re never stuck in a voicemail loop while water is coming in. Technicians are background-checked, arrive in uniform, and can diagnose the opening and the structure behind it on the same visit instead of handing you off to three different trades.
Frequently Asked Questions
Condensation between the panes means the perimeter seal on the insulated glass unit has failed, allowing moisture to enter the space between the glass. That’s not a cleaning problem; the desiccant has saturated and the fog won’t wipe away. In San Francisco’s fog belt and coastal neighborhoods, we see seal failures at roughly 8 to 15 years on many units. Call (866) 320-2646 for an assessment – the fix is usually replacing the glass unit, not the whole window.
A door that sticks only in winter is usually responding to seasonal wood movement or a small foundation shift tied to soil moisture. The door isn’t the problem; it’s the messenger. If the reveal is uneven, planing the edge is masking a structural issue that will cost more to fix later. Call (866) 320-2646 for a free estimate that includes a look at the whole opening.
Most window problems are repairable. Fogged glass, worn weatherstripping, and most hardware failures are fixed by replacing the component, not the whole unit. Full replacement makes sense when the frame is rotten, the product is far past its service life, or you’re replacing for energy performance anyway. Andersen and Marvin are among the brands we specify when replacement is the right answer. Call (866) 320-2646 for an honest assessment before you commit to either path.
Water intrusion is almost always a flashing or seal failure, not a window defect. Missing sill pan flashing, backward-lapped head flashing, and gaps in the frame-to-wall seal are the usual suspects. In San Francisco, wind-driven rain against west- and seaward-facing walls finds every weak point. If you see water inside the wall, don’t add more caulk – call (866) 320-2646 and let a professional trace it to the source.
Check the reveal. An even gap around a sticking window or door points to hardware or seal failure. An uneven gap, cracks at the corners of the opening, or multiple openings sticking on the same wall point to structural movement. In San Francisco’s pre-war housing stock, that’s common enough to be the first thing we check. Call (866) 320-2646 for a free estimate if you see any of those signs.
Not when the pricing is done right. Groundwork Construction Co. of San Francisco gives no-hassle upfront pricing – the number you see is the number you pay, with no change orders dropped on you mid-job. Every repair we do is covered by the 730-Day Done Right Promise. Projects over $10,000 also qualify for $1,000 off and 0% financing for 18 months. Call (866) 320-2646 for a free estimate with line-item pricing.
The Bottom Line
Windows and doors don’t fail at random. Every symptom – drafts, sticking, fog, water, hardware – traces back to a product failure, an installation failure, or a structural signal, and each one has a different fix and a different responsible party. Diagnose the cause before you repair the symptom. In San Francisco, fogged glass is a seal problem, water intrusion is a flashing problem, and a door that sticks every winter is the house talking. Reach for the quick fix only when it’s legitimate, avoid the ones that mask a bigger bill, and keep a record of what you find. That’s how a $40 repair stays a $40 repair instead of turning into a five-figure one.
If you’re not sure which category your problem falls into, Groundwork Construction Co. of San Francisco provides free estimates with transparent, upfront pricing and a 730-Day Done Right Promise on every job. Call (866) 320-2646 to schedule yours. Live person, 24/7.
Written by the team at Groundwork Construction Co. of San Francisco.