Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterBathroom Vanity Installation Cost in San Francisco, CA
Bathroom vanity installation in San Francisco runs $945-$3,540 for a straightforward swap, and $2,200-$6,800 once a pre-1960 wall opens up and the plumbing and floor underneath need real work. Those cheap $300 quotes you see on gig apps don’t account for 60-year-old galvanized pipe or a tile floor that was never finished past the old cabinet footprint. Call (866) 320-2646 for a free estimate with the full scope in writing, not a guess from a photo.
We’re Groundwork Construction Co. of San Francisco, and the honest talk below is what we wish every homeowner heard before signing a low-ball bid on a Victorian or Edwardian bath.
Why the lowest quote rarely survives contact with an old SF bathroom
The quote is for the vanity. The invoice is for what’s behind it. In a pre-1960 San Francisco row house, that’s where the story turns.
Open the wall behind the old cabinet in most Sunset or Richmond District homes and you’ll find galvanized iron supply lines. That pipe corrodes from the inside out, so by the time it’s 50 or 60 years old the bore is choked with rust scale and the shutoff valves haven’t been turned in decades. When we go to isolate the water for the swap, those valves frequently won’t close or fail outright. Replacing them isn’t an upsell; it’s a code and safety requirement, and it’s usually $250-$600 nobody budgeted for.
Then there’s the drain. The rough-in on these homes was set for a cabinet depth that vanished from showroom floors a generation ago. Modern vanities are often 21 to 22 inches deep against an 18-inch legacy rough-in, so the P-trap and drain line need adjustment to line up – another $200-$500.
And the floor. Older SF bathrooms were tiled only under the original vanity footprint. Change the width or depth of the new cabinet, and you expose bare subfloor where the tile stopped. That gap isn’t cosmetic. It fails a moisture inspection and it looks like a job that quit halfway. Filling it runs $300-$700 depending on whether we can match the existing tile.
Any of these three can turn a $1,500 install into a $3,500-$5,000 scope in an afternoon. None of them are visible until the wall opens.
What the real installed cost breaks down to
Here’s the line-item picture for a typical San Francisco vanity install. The low end fits a newer condo or a simple swap in a home with modern plumbing. The high end fits a pre-war row house where the wall needs work.
| Item | Low | High |
|---|---|---|
| Vanity cabinet | $400 | $2,000 |
| Countertop and sink | $300 | $1,200 |
| Faucet | $150 | $600 |
| Shutoff valve and supply line replacement (galvanized homes) | $250 | $600 |
| P-trap and drain rough-in adjustment | $200 | $500 |
| Floor tile fill-in if footprint changes | $300 | $700 |
| Labor | $600 | $1,200 |
| Honest total range | $2,200 | $6,800 |
Our published range for Bathroom Remodeling in San Francisco work in general runs $10,620-$33,040, and a single vanity sits inside that as one piece of a larger project. For context, a full Bathroom Remodeling scope wraps cabinet, tile, shower, and finishes together so nothing gets priced in isolation.
How Groundwork handles the surprises before they become surprises
The reason install costs blow up is that nobody assessed the wall before the cabinet came off. We do the assessment up front.
Before we quote, we open the cabinet doors, check the shutoff valves, look at the drain rough-in relative to the footprint of what you’ve chosen, and look at what the floor tile is doing under the old vanity. That pre-install walkthrough takes maybe 20 minutes. It’s what turns a written scope into a number you can trust.
- Supply line condition – galvanized, copper, or PEX, and whether the valves actually close
- Drain rough-in location – measured against the depth of the vanity you’ve chosen, not the one on the showroom floor
- Floor tile condition – how far it extends, and whether a footprint change exposes anything
- Wall condition behind the cabinet – water stains, rot, anything the old vanity was hiding
You get home improvement pricing in writing before demo starts, backed by the same 730-Day Done Right Promise we put behind every project. If it’s not done right, we make it right.
You also get the durability side handled. On the west side of the city, where the fog belt and salt air eat standard fasteners and paint within a fraction of the normal lifespan, we spec stainless hardware and galvanized fittings even on a small vanity job. Faucets and sinks from Kohler hold up to that environment better than builder-grade chrome; sink tops from Cambria don’t stain from the daily water exposure. We source from partners whose products we’d put in our own homes, and we put the number in writing so you choose quality, not just availability.
The leak that shows up six months after the vanity goes in
The most common failure mode on a vanity install is a slow leak behind the cabinet. A drain connection that isn’t seating quite right, a supply fitting that works loose, and water drips into the void under the cabinet where nobody sees it until the wood swells or the floor buckles.
That’s the whole reason a written workmanship guarantee matters on this job. Our 730-Day Done Right Promise covers plumbing connections and fittings. If moisture appears under your vanity within 730 days, it’s our problem to fix, not yours. That’s not a small thing on a pre-war home where the plumbing is already tired.
Common local scenarios we run into
Sunset District two-story: Galvanized supplies, original shutoffs frozen in place, tile stopping right at the old vanity edge. Full scope lands near the top of the range, but the wall gets done right once instead of three times.
Richmond District Edwardian: Someone swapped the vanity in 1998 and left the drain rough-in mismatched. We rebuild the trap arm to fit the new cabinet and get the connection bringing it back to code.
Mission District condo conversion: Modern copper and PEX, current shutoffs, tile floor that runs wall to wall. A vanity swap here is a clean $945-$1,800 because there’s nothing waiting in the wall.
Contracting on these dense old row houses is tight-lot work all day long, and the pre-1906 and post-1906 rebuild mix means two houses on the same block can have completely different plumbing. We’ve been building here since 2014, and our technicians carry up to 12 years of experience. They’re background-checked and uniformed because how a crew shows up tells you something about the work.
FAQs
Bathroom vanity installation in San Francisco runs $945-$3,540 for a clean swap, and up to $6,800 in a pre-1960 home where the wall opens up and the supply lines, drain, and floor tile all need attention. The difference between the two is almost entirely the age of the plumbing behind the cabinet. Call (866) 320-2646 for an exact quote – the estimate is free and it’s in writing.
Because online numbers assume modern plumbing and a finished floor. In a Victorian or Edwardian bath, galvanized supply lines, mismatched drain rough-ins, and tile that stops at the old cabinet footprint add $1,500-$3,500 of real scope that isn’t visible until demo. Our pre-install assessment catches those items before the quote goes out, so the number you see is the number you pay. Call (866) 320-2646 and we’ll walk you through what your specific bath likely needs.
Yes, if they won’t close cleanly. Old galvanized systems often have valves that haven’t been turned in decades and fail when we try to isolate the water for the swap. A valve that won’t shut off is a code and safety problem, not an upgrade. Replacing them runs $250-$600 and happens before any cabinet comes off the wall. For a written estimate, call (866) 320-2646.
Not usually, and that’s why it matters. Older San Francisco bathrooms were tiled only under the original vanity footprint, so a new cabinet with a different width or depth exposes bare subfloor. We fill and finish that gap as part of the scope – $300-$700, depending on matching the existing tile – so the install doesn’t fail a moisture inspection and doesn’t look unfinished. Call (866) 320-2646 to schedule a free assessment.
Get a written number before the wall opens
Live person answers our line 24/7, so you don’t wait until Monday to get moving. Call (866) 320-2646 for a free estimate and design consult on your bathroom vanity project. Upfront pricing, no surprises, and a 730-Day Done Right Promise in writing. That’s how we work in San Francisco – and how we’d want it done on our own home.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco, CA.
What Our Customers Say
"Found unpermitted work by the previous owner once he opened the wall. He stopped, explained the options and what each would cost, and let me decide rather than making it my emergency."
- Marco Castillo"He told me one part of what I wanted was a bad idea structurally and offered an alternative instead of just taking the money."
- Angela Wong"He pulled the permits himself, scheduled every sub and ran the inspections. I made one decision a week and otherwise stayed out of it, which is exactly what I was paying for."
- Robert Sullivan