Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Home Additions & ADU: The San Francisco Owner’s Guide
We build home additions and ADUs in San Francisco using Barrette-branded structural and finish components, and a full addition typically runs $53,100 – $153,400 installed, while a detached or attached ADU runs $106,200 – $259,600. A garage conversion, the most common Barrette-component project we see, lands between $35,400 and $94,400. These are planned projects, quoted in writing before a single permit is pulled, not same-day fixes.
Owners usually discover a Barrette component has failed long after the build. The symptoms show up quietly: a door in the new wing that no longer latches, a roofline over the addition that sags at the seam, a floor that’s gone soft near the ADU entry, or trim that’s pulling away from the frame. In San Francisco’s fog belt, where exterior components sit in salt air and constant moisture, these failures surface years earlier than they would inland. We’re an independent San Francisco construction company, not affiliated with Barrette, and we diagnose the actual part before quoting a repair or a rebuild.
Which Barrette Models This Applies To
Barrette doesn’t sell home additions as a single packaged product the way it sells railing or fencing. What San Francisco owners typically have are Barrette structural connectors, post bases, framing hardware, or Barrette exterior components spec’d into an addition or ADU by a prior builder. The compatibility question is almost never “which Barrette model” in the consumer sense, it’s “which Barrette series or spec sheet was used on my project” so the replacement matches load rating and finish.
Start by finding the documentation. Look for a spec sheet, plan set, or permit drawing left with your closing documents, and check the framing hardware itself for a stamped Barrette part number. Measure the existing component before ordering anything: a post base or connector that’s a quarter-inch off won’t seat, and the load rating has to match or exceed what your plans require. When you can’t find a number, we cross-reference the assembly by measurement and load spec. The OEM-versus-aftermarket call matters here: for structural connectors, we match or exceed the original load rating and won’t substitute a lighter part to save money. For finish components, a quality equivalent is often the smarter buy. We also work with KraftMaid, Cambria, and Silestone when an addition includes cabinetry or countertops, and buy those through verified partners in San Francisco.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Home Additions & ADU Is Failing
- Sagging at the addition’s roofline seam. A connector or hanger has loosened or corroded, letting the roof structure settle. In San Francisco’s marine air, exposed hardware corrodes faster than most homeowners expect, and it shows up as a visible dip where the new roof meets the old.
- Doors and windows in the addition that won’t latch. This usually means the framing has shifted, often because a structural connection wasn’t rated for what was hung on it. A door that drags or pops open is the earliest tell.
- Soft or bouncy floors near the ADU entrance. A post base or beam connection has lost contact, transferring load where it wasn’t designed to go. Step on it and you’ll feel the give before you see it.
- Trim and flashing pulling away from the exterior. Moisture has worked behind a poorly seated connector or fastener, and the finish is telling you the assembly underneath is moving. Left alone in a foggy San Francisco season, it turns into rot.
- Visible rust or corrosion on exposed hardware. Salt air eats standard galvanized parts. If you can see rust streaking down the framing, the connector’s holding power is already compromised.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
We quote additions and ADUs as a line-item range, so you see the component cost, labor, permit fees, and inspection separately. A full home addition in San Francisco runs $53,100 – $153,400 depending on square footage, foundation work, and how much of the existing structure has to be opened up. An ADU runs $106,200 – $259,600, and a garage conversion sits at $35,400 – $94,400. A targeted structural connector or component replacement, where the failure is isolated, is priced well below those full-project numbers.
What moves the price: foundation and seismic work (San Francisco’s soft-story and seismic requirements are strict), permit and inspection fees, how much toggling to the existing structure is needed, and whether the failure has spread. What’s included in every quote: the matched part, permit pull, labor, and inspection pass. There’s no change-order gamesmanship. The number you see is the number you pay, and every job carries the 730-Day Done Right Promise, backed in writing. A free estimate and design consult comes first, and 0% financing for 18 months is available, with $1,000 off projects over $10,000.
DIY or Call Us?
You can safely find your documentation, read a stamped part number, measure the existing component, and photograph any rust or separation. That information helps us quote fast. What you don’t want to handle yourself is anything structural: a loose connector or hanger on an addition or ADU is carrying real load, and getting the rating or the connection wrong risks the structure or yourself. High-tension and load-bearing components aren’t a homeowner repair.
The seam on the addition and the framing in the ADU are places where a wrong guess gets expensive and dangerous. Our technicians have up to 12 years of experience reading exactly these assemblies. Call us at (866) 320-2646 to walk through what you’re seeing before you touch a structural part.
FAQs
Structural connectors and framing hardware typically last 20 to 30 years when properly galvanized, but San Francisco’s salt air and marine moisture can shorten that to 10 to 15 years on exposed exterior assemblies. Interior hardware lasts longer. If you’re near the water or in the fog belt, inspect exposed connections more often.
Sometimes, when the corrosion or movement is minor and the load path is intact, a repair with a matching-rated reinforcement works. When the connector has lost load capacity, replacement is the right call, and we’ll tell you which it is. Call (866) 320-2646 for a free estimate.
An isolated connector or component swap is often a single-visit job. A repair tied to structural movement or a section of the addition may run longer once permits and inspection are folded in. We schedule planned work, not rushed fixes, and give you a realistic timeline in writing.
We match by the stamped part number on your existing hardware or by measured load spec when no number is available, and we won’t substitute a lighter part for structural connections. We buy through verified brand partners and confirm the rating before ordering. Call (866) 320-2646 to start your free estimate.
Ready to price it? Call (866) 320-2646 for your free estimate and design consult, and we’ll put the number in writing. Live person, 24/7. Upfront pricing, no surprises. From foundation to finish line, built to last and backed by the 730-Day Done Right Promise. If it’s not done right, we make it right.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.