A Groundwork company - serving San Francisco, CA

Cover Roofing in San Francisco, CA

RoofingRoofing
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Cover Roofing: The San Francisco Owner’s Guide

Cover-compatible roofing for San Francisco homes typically runs $470 – $2,125 for targeted repairs and $9,440 – $23,600 for a full replacement, installed by our background-checked, uniformed technicians and backed by our 730-Day Done Right Promise. Most repair work is completed in a single visit; full replacements are scheduled estimates, not same-day jobs.

Call (866) 320-2646

Here’s how San Francisco owners usually find us. A six-inch sheet metal “cover” flashing piece at a chimney, skylight curb, or parapet edge has curled, rusted through, or pulled loose from its fasteners. The first hard rain sends water down the inside of a wall in the Sunset or Potrero Hill. Or the owner is up top after a windy night and sees the cover flashing flapping at a corner. That’s when we get the call.

Which Cover Models This Applies To

Cover flashing is a general term for the top-of-cavity metal piece – counterflashing, head flashing, or a cover cap – that sheds water over the laps below it. It’s not a single interchangeable product, so matching matters. Measure three things before you order anything: the developed width (how wide the metal is before it’s bent), the gauge (23-gauge is standard for residential; heavier where it steps over a parapet), and the profile – the exact bends, including any drip hem or kick-out.

A compatibility gotcha that bites a lot of San Francisco buyers: the cover piece must overlap the flashing below it by at least 4 inches and terminate in a hem that diverts water clear of the wall, not flush against it. A cover cut to the old piece’s dimensions will run short. For material, we recommend coated steel or pre-finished copper – standard galvalume and bare steel rust fast in our salt air and fog, and we see 6-to-10-year failure on those in exposed areas.

OEM parts from the original roofer or manufacturer rarely exist for flashing (it’s cut on-site), so quality fabrication by a sheet metal shop is the norm – and preferable. Groundwork Construction Co. of San Francisco is an independent service provider and is not affiliated with Cover.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Cover Roofing Is Failing

  • Rust bloom or pinholes along the fold. Salt fog and marine air corrode the thinnest part of any bend first. Once you can see daylight through it, water is getting in.
  • Lifted fasteners or sealant pulling away. The screws that pin the cover to the roof deck or wall have backed out, or the sealant underneath has dried and cracked. Wind and sun do this over time.
  • Rusted or curled drip edge at the exposed lip. The bottom edge loses its kick-out and water starts running backward under the shingles.
  • Interior water stains near a chimney, skylight, or parapet. The cover is the #1 suspect when the wet spot is directly below the roof penetration.
  • Daylight or sag visible where the cover meets the wall. The piece has separated and is no longer shedding water away from the siding or stucco.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For San Francisco, expect $470 – $2,125 for roof repair that covers replacing cover flashing, and $9,440 – $23,600 for a full roof replacement when the flashing failure has rotted the deck or laps far beyond repair. Metal roof work runs $17,700 – $47,200 across that full range of size and material.

What moves the number: access and height (steep or tight-lot work costs more), how many penetrations you have, whether the deck underneath is soft, and material choice (pre-finished copper costs more than coated steel).

Our quotes are line-item: so many feet of cover piece, so many hours of labor, disposal, and accessories, all separate. That’s upfront pricing with no surprises – the number you see is the number you pay. Every install carries our 730-Day Done Right Promise: if it’s not done right, we make it right.

DIY or Call Us?

Check the visible stuff first. Look for rust, loose fasteners, or lifting lip from the ground with binoculars or a ladder kept on solid footing, and note any interior stains before the next storm. That’s where honest DIY ends. Roofing metal takes fabrication (a sheet metal brake and shear), correct overlap and fastening, and full underlayment behind the cover to back up the joint.

Go up on a pitched roof and try to cut and bend your own cover and it looks wrong, leaks worse, or you fall – that’s the story we hear most. This is a trained, insured professional’s job.

For an exact quote, call us at (866) 320-2646 – we answer live, 24/7, and free estimates are on us.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch