Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Delta Windows & Doors: The San Francisco Owner’s Guide
We install and repair Delta-compatible windows and doors throughout San Francisco, with full window and door replacement typically running $5,310 to $17,700 installed, and impact-rated units at $9,440 to $29,500 when your opening calls for them. Delta covers a wide spread of window and entry-door lines, so the part in your hand or the sticker on your sash matters – the right match is what keeps a repair small. Owners usually find the problem the same way: a sash that drags instead of gliding, a door that won’t latch without a shoulder, or fog between panes that no amount of cleaning touches. That’s a hardware, seal, or glazing failure, and it’s worth pricing before it spreads.
We’re an independent service provider, not affiliated with Delta. When we write a part or a replacement, we’re matching it to your actual unit and the way it should perform in San Francisco’s marine air.
Which Delta Models This Applies To
Delta’s residential catalog runs several families: vinyl slider and single-hung windows, awning and casement windows, and hinged patio and entry doors. The failure point you describe usually locates the family. Rollers and tandem roller assemblies fail on sliders and patio doors. Sash balances, pivot bars, and tilt-latch hardware fail on single-hung and double-hung sashes. Hinges, sill sweeps, and threshold weatherstrip fail on hinged doors.
Identify your unit before you buy anything. On most Delta windows, the glass-to-frame spacer and the interior stop carry a label with the series designation and a manufacturing date; the sash itself may have a stamped mark in the top channel. If the label is gone, measure. Measure the visible glass width and height to the nearest 1/16 inch, then the overall frame height and width at the opening. Delta sized its lines to common nominal dimensions, but a 35 1/2-inch sash and a 36-inch sash are not the same part, and the difference is the most common reason a returned roller or balance won’t fit.
On the OEM-versus-aftermarket question, the honest answer for Delta is a split. Tilt latches, pivot bars, and screen hardware have solid quality aftermarket equivalents that cost roughly a third to half of OEM and hold up just as well. Sash balances and roller assemblies are where we stay OEM or OEM-spec; a mismatched balance rated for a lighter sash will let a heavy unit drop within months, and the spring tension ratings don’t cross-reference cleanly between brands. Insulated glass units should be ordered to the exact spacer width and tint to match the rest of your set.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Delta Windows & Doors Is Failing
- The sash drops or won’t stay open. A worn sash balance has lost its spring tension, or a broken pivot bar let the balance slip off. This is the first thing to check on a single-hung that suddenly won’t hold position.
- A roller drags or the door jumps the track. Worn tandem rollers or a track that has collected grit and salt air. On San Francisco sliders facing the fog belt, we see this a lot because the rollers sit low and gather debris.
- Fog or condensation between the panes. The sealed glass unit’s perimeter seal has failed and moisture has entered the airspace. No cleaning fixes this; it’s a glazing replacement, not a hardware swap.
- The door won’t latch or rubs the strike. Hinge wear, a sagging hinge jamb, or a shifting threshold. In older San Francisco homes, a settling foundation often transfers movement into the door opening and shows up as a latch that used to catch cleanly.
- Drafts, water staining, or soft weatherstrip. Worn sill sweeps and compressed weatherstrip let the fog and wind in. It shows as a cold edge in winter and staining on the interior sill after a storm.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in San Francisco depends on opening size, the material, and whether we’re swapping a part or a whole unit. Here are the ranges we quote:
- Window replacement (full unit, installed): $5,310 to $17,700
- Impact-rated window installation: $9,440 to $29,500
- Part-and-labor repair on a failed balance, roller, or hinge: usually a small fraction of a full swap, priced after we confirm the model and part
The range is driven by unit size, glass package (standard versus impact, low-E, or tinted), the number of openings in the job, and what we find behind the trim – old San Francisco openings sometimes need flashing and reframing that a straight swap doesn’t. We quote parts and labor separately so you see exactly what a matching part costs versus a full unit. Every install is covered by our 730-Day Done Right Promise, and we call the number you see the number you pay.
DIY or Call Us?
Some of this is genuinely a homeowner check. Measure your sash and glass carefully, look for the series label, test a roller by lifting the door slightly, and confirm the fog is between the panes rather than on the glass. What we’d avoid doing yourself is balance and roller replacement on a heavy two-story or door-height unit – the sash can drop, and getting it back in the frame without cracking the glass or pinching your hand is where most DIY attempts go wrong. On a marine-air climate like San Francisco’s, a badly reseated sash also invites leaks fast.
If the unit is big, the glass is fogged, or the door has shifted in its opening, that’s a job for us. Call (866) 320-2646 and we’ll match the right part and quote it upfront – estimates are free.
FAQs
Expect rollers and balances to be the first parts to go, often within 8 to 15 years depending on exposure, while the frame and glass can last decades. The fog belt and salt-laden air on the west side and near the water wear hinges and rollers faster than inland neighborhoods. Call (866) 320-2646 for an exact quote on a repair – estimates are free.
Usually yes. A failed balance, roller, or hinge is a targeted repair and costs a fraction of a full unit. Repairs make sense when the frame and glass are sound; a fogged sealed unit or a rotted frame means replacement.
A single part-and-labor repair commonly completes in a single visit, while a full window or door replacement depends on the opening and how many units you’re doing. We’ll tell you the realistic window when we quote.
We match your series and measurements to an OEM part or a quality OEM-spec equivalent, and we confirm the spec before ordering. We don’t carry parts on a truck – we source the correct part for your model and schedule the install. Call (866) 320-2646 to get started – estimates are free.
Ready to stop guessing at the part? We also service KraftMaid, Cambria, and Silestone on other projects. Call Groundwork Construction Co. of San Francisco at (866) 320-2646 for a free estimate, upfront pricing with no surprises, and work backed in writing by our 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.