Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Home Additions & ADU: The San Francisco Owner’s Guide
We build Moen-plumbed home additions and ADUs in San Francisco, and a whole-project addition typically runs $53,100 – $153,400 installed, with an ADU at $106,200 – $259,600. This is planned construction, not emergency work, so scheduling follows design and permitting, not a same-day dispatch. Most owners land here after a smaller problem surfaces: a Moen rough-in valve that weeps behind a new bathroom wall, a tub filler that won’t hold pressure for a second-floor addition, or a shower cartridge that starts dripping within months of a remodel handoff.
Groundwork Construction Co. of San Francisco is an independent builder. We are not affiliated with Moen, and we don’t stock or carry Moen parts.
Key Takeaways
- Moen’s 1222 and 1225 cartridge family covers most single-handle tub and shower valves you’ll find in San Francisco homes, but the two are not interchangeable.
- San Francisco’s soft, low-mineral water is easier on cartridges than hard-water markets, but the city’s older galvanized supply lines and pressure swings do more damage than scale ever will.
- Additions and ADUs are permitted projects. Plumbing rough-in gets inspected before the wall closes, so the valve has to be right the first time.
- The 730-Day Done Right Promise covers our workmanship, and the number you see on the estimate is the number you pay.
Which Moen Models This Applies To
Moen single-handle tub and shower valves are the ones that matter on an addition or ADU, and the model line is defined by the cartridge inside the rough-in valve, not by the trim you see. The 1222 is the standard brass-bodied cartridge used in Moentrol and Posi-Temp valves. The 1225 is the plastic-bodied version of the same fit, and Moen sells both for the same housings. If your trim plate says Moentrol, Posi-Temp, or 1200/1225 series, you’re in this family.
To identify the right part, pull the handle and trim plate and read the stamping on the cartridge face, or measure the valve body behind the wall. A 1222 measures roughly 4 inches overall with a brass stem; the 1225 is the same length in a composite body. Where owners go wrong is ordering by the faucet’s finish or model name from the box, which describes the trim, not the valve. For Moen specifically, the OEM cartridge is inexpensive enough that a knock-off rarely pays. The aftermarket copies we’ve pulled out of failed jobs tend to have softer seals that weep within a year. KraftMaid, Cambria, and Silestone are among the other brands we work with on the finish side of these projects.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Home Additions & ADU Is Failing
- A drip from the tub spout that won’t stop. The cartridge seals have worn and water is passing through even in the off position. In an addition with a new tub, this usually shows up within the first year if the valve was set with debris in the line.
- Temperature that drifts or won’t hold. A failing pressure-balancing spool inside a Posi-Temp valve lets hot and cold cross. You’ll notice it most in a second-floor ADU shower where pressure is already lower.
- Water staining on the ceiling below. A weeping rough-in valve or a loose connection behind the wall. This is the one that costs real money, because it means opening drywall on a finished addition.
- Handle that turns hard or feels gritty. Mineral film and worn internal stops. San Francisco’s water is soft, so this is usually age, not scale, and it’s the earliest warning you’ll get.
- Low flow at one fixture only. Often a clogged cartridge screen or a shutoff that wasn’t fully opened after rough-in. Worth checking before you assume the valve failed.
Replacement Cost & What’s Included
For a single Moen cartridge or valve swap inside an existing addition, the typical installed cost in San Francisco runs $180 – $420, parts and labor, when the wall stays closed. If the valve body has to be replaced or the wall opened, expect $450 – $1,100 depending on access and drywall repair. On a full addition or ADU build, plumbing rough-in and fixture setting are part of the project number, from $53,100 – $153,400 for an addition and $106,200 – $259,600 for an ADU.
What drives the range: whether the wall has to open, whether it’s a cartridge or the whole valve, and finish repair afterward. We quote parts and labor as separate line items so you can see what the hardware costs versus the work. All of it is covered by the 730-Day Done Right Promise, and the estimate is what you pay.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely shut off the water at the fixture stops, pull the handle and trim plate, and read the cartridge stamping or snap a photo. That’s a five-minute check and it tells us exactly which part to bring. What you shouldn’t do is open a valve body inside a finished wall, cut into supply lines, or work on a pressurized rough-in without shutting off and draining the line. Water damage behind an addition wall costs far more than the repair. If the valve is behind tile in a new ADU bath, call us before you touch it. Our technicians have up to 12 years of experience with Moen valves and the older San Francisco plumbing they sit on. Call (866) 320-2646 and we’ll get you a free estimate.
FAQs
Most Moen 1222 cartridges last 8 – 12 years and often longer in San Francisco, because the city’s soft water puts little mineral stress on the seals. The bigger factor here is pressure and old supply lines, not water hardness, so a valve set on a line with pressure swings may fail sooner. Call (866) 320-2646 for an exact quote on replacing yours.
Usually yes, if the valve body is sound. The cartridge is the wear item, and swapping it fixes most drips and temperature problems without opening the wall. If the body itself is cracked or corroded, the whole valve goes. We check before recommending the bigger job.
A cartridge replacement is a one-visit job, typically under two hours. A full valve replacement with wall access runs a day including drywall patch, and we schedule it around your use of the room. Estimates are free, so call (866) 320-2646 to line it up.
We order the specific cartridge or valve by model number, OEM, once we’ve confirmed it against your valve body. We don’t carry parts or keep them on a truck, so we identify first and order exact. That avoids the wrong-part second visit. Call (866) 320-2646 for a quote.
Get Your Free Estimate
Whether you’re chasing a drip in a finished ADU bath or planning a full addition from the foundation up, call Groundwork Construction Co. of San Francisco at (866) 320-2646 for a free project estimate and design consult. Live person, 24/7. Upfront pricing, no surprises, and a 730-Day Done Right Promise behind the work.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.