Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Oldcastle Home Additions & ADU: The San Francisco Owner’s Guide
For San Francisco homeowners planning an Oldcastle-led addition or ADU, the structural shell and modular components are the part of the project that either holds the build together or quietly causes the failures you notice months after move-in. Installed additions across San Francisco typically run $53,100 – $153,400, while full ADU construction lands between $106,200 – $259,600 and garage conversions between $35,400 – $94,400. The tricky part is that failures here rarely announce themselves. Owners discover them as a door that won’t close square at the back of a Sunset addition, a cold seam near the addition roofline, or a slow crack creeping up the joint where the new wing ties into the original house.
Which Oldcastle Models This Applies To
Oldcastle ships several product families relevant to additions and ADUs, including modular wall and floor panels, precast finish components, and site-wall systems built for Western climates. Identifying the right replacement part starts with the ID plate on the panel or component itself, not the model name on the original contract. Panel edges carry a stamped or labeled series reference (usually a letter-number combo), and a tape measure across the panel width plus a note on the connection hardware gets you a matchable part spec.
For Oldcastle, the OEM decision is more nuanced than it is for appliances. Some components (structural connectors, panel-specific flashing) should be sourced OEM because the tolerance and coating match the panel line, while decorative finishes and standard trim often have quality aftermarket equivalents that cost less and perform the same. If your addition was permitted in San Francisco within the last decade, that permit record will also tell you which Oldcastle series was specced. Groundwork Construction Co. of San Francisco is an independent service provider, not affiliated with Oldcastle, so we match parts by spec rather than by brand loyalty. We also service KraftMaid, Cambria, and Silestone where those products intersect with your remodel scope.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Oldcastle Home Additions & ADU Is Failing
Every failure leaves a signal. Here are the five we see most in San Francisco additions and ADUs, along with what’s actually behind each one:
- A door or window won’t close flush. This usually means the panel or header has shifted, often from settling where the addition ties into the original foundation. If you hear a click before the latch catches, the frame is already out of square.
- Caulking or sealant at the joint fails within a year. San Francisco’s fog belt and constant humidity cycles work sealants harder than most climates. When the joint re-opens every season, the panel movement is the real cause, not the caulk.
- A seam between panels or between addition and house reveals a crack. Thermal movement is the usual culprit. A hairline crack that widens with the weather is structural movement; one that stays stable is usually cosmetic.
- Water staining or soft drywall at the top of the addition wall. This is flashing failure at the panel-to-roof junction, and it’s urgent. In San Francisco’s wet winters, a small leak at that seam eats into framing fast.
- Floors feel uneven or dip near interior walls. This is subfloor panel fatigue or a failed connector. If it appears only in one room, isolate it to that panel; if it spans the addition, the tie-in point needs inspection.
Replacement Cost & What’s Included
Panel or component replacement pricing in San Francisco depends on three things: which part failed, whether access requires opening finishes, and whether the fix needs permits. Expect an addition repair or partial replacement in the $53,100 – $153,400 range for a project of meaningful scope, with ADU-level work in the $106,200 – $259,600 range. Garage conversions sit lower, at $35,400 – $94,400. The parts-plus-labor breakdown is transparent: the panel or component is priced at OEM or equivalent, and labor is scoped in writing before we start.
Groundwork Construction Co. of San Francisco includes written line-item estimates and pulls permits where San Francisco requires them. All workmanship is covered by the 730-Day Done Right Promise: if it’s not done right, we make it right. The number you see is the number you pay. No change orders unless you approve them.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
There are a few things you can safely check on your own. Look at the joint where your addition meets the original house after a rain and note whether water beads or pools. Check that doors close without resistance. Measure the width of any crack and recheck it in a month to see if it’s moving. Those observations will help a technician diagnose the failure faster.
What you shouldn’t do is try to remove or replace a structural panel, adjust a load-bearing connector, or seal an active roof-panel flashing leak on your own. In San Francisco, panels can be load-bearing, and opening the wrong fastener can destabilize a wall section without obvious warning. This isn’t the kind of repair to learn from a video. Call (866) 320-2646 and we’ll tell you whether the issue is a component replacement or a smaller fix.
FAQs
Panel and structural component lifespans run 25 – 40 years when installed and flashed correctly. In San Francisco, the ocean air and fog cycle accelerate wear on anything exposed to weather, so coastal-facing panels may show their first signs of failure around year 20. If you’re at year 15 and seeing seam movement, it’s worth an inspection before small issues grow.
Often yes. Cosmetic cracking, isolated sealant failure, and small flashing issues can be repaired without a full panel swap. Structural movement, subfloor fatigue, or a connector that’s failed under load usually means replacement of that panel or component. A technician on-site can tell you which you’re dealing with in under an hour. Call (866) 320-2646 to schedule an inspection.
A single component swap typically runs one to three days, depending on finish access and permit timing. A larger structural repair that opens walls and reinstalls finishes can run one to three weeks. San Francisco permit processing adds time to projects that require it, and we build that schedule estimate into your written quote so you’re not surprised.
We match by spec, not by brand name. We pull the Oldcastle series reference from your panel ID or the original permit record, then source the OEM component or an equivalent that meets the same tolerance and coating requirements. You’ll see the part and the labor line in your written estimate before we order anything. Call (866) 320-2646 for a free estimate.
Get an Oldcastle Addition or ADU Estimate in San Francisco
Whether you’re chasing a failing panel joint, planning a new addition, or converting a garage into a livable ADU, the fastest way to get a real number is to call us. Our technicians have up to 12 years of experience with structural and modular additions, and we bring upfront pricing, written line-item estimates, and the 730-Day Done Right Promise to every job. Call (866) 320-2646 for your free estimate and design consult. Calls are answered by a live person, 24/7. From foundation to finish line, we build it, we back it, and we stand behind it in writing.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.