Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Windows & Doors: The San Francisco Owner’s Guide
We install and service PGT windows and doors for San Francisco homeowners, and most full window replacements run $5,310 – $17,700 installed, with impact-rated units landing at $9,440 – $29,500. The parts that fail most often are the ones you can’t see: balances, rollers, glazing gaskets, sash locks, and weatherstripping. Owners usually notice the problem the same way. A double-hung sash won’t stay up. A slider drags halfway and stops. Fog creeps between the panes after a cold night in the Sunset. Or water shows up on the interior sill after the first big rain of the season, and the frame tells you the seal has been gone for a while.
We stock no parts and nothing rides on a truck. Every replacement part gets matched to your exact PGT series and measured before we order it, which is the only way to get it right the first time. Groundwork Construction Co. of San Francisco is an independent service provider and is not affiliated with PGT.
Key Takeaways
- Most PGT part failures trace to worn balances, rollers, gaskets, or weatherstripping, not the frame itself.
- Installed window replacement in San Francisco runs $5,310 – $17,700; impact-rated glass runs $9,440 – $29,500.
- Parts are matched to your series and measured on site before ordering, and all work is covered by our 730-Day Done Right Promise.
- A live person answers our line, 24/7, when you call (866) 320-2646.
Which PGT Models This Applies To
PGT makes a wide range of window and door lines, and the part you need depends entirely on which one is in your wall. The most common residential lines we see in San Francisco are the Vinyl Series double-hung and slider windows, the WinGuard impact line, and PGT sliding glass and French doors. Each line uses different balance assemblies, roller styles, and gasket profiles. A balance from a Vinyl Series sash will not fit a WinGuard sash, even when the window sizes look identical from across the room.
The reliable way to identify your model is to find the manufacturer label. PGT places it in the head jamb of operable windows, on the interior face of door panels, or sometimes inside the frame channel where the sash travels. You’ll also find a glass label if the unit is impact-rated, which matters because WinGuard glass and standard annealed glass need different gaskets and setting blocks. If the label is gone, measure the sash width, height, and thickness at the meeting rail and photograph the balance or roller in place. Those three measurements plus a clear photo usually identify the part.
On the OEM question, PGT factory parts are the safest match for anything structural to the sash movement: balances, pivot bars, and rollers. For gaskets and weatherstripping, a quality aftermarket extrusion with the correct durometer and profile performs as well and often costs less. We make that call per part, not per job, and we tell you which way we’re going and why.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your PGT Windows & Doors Is Failing
PGT hardware is built to last, but San Francisco’s marine air and the sun load on south-facing glass work on it steadily. Here’s what we hear most often and what’s actually happening underneath.
- The sash won’t stay up, or slams down. The spiral or block-and-tackle balance has lost tension. Balances wear out faster on windows that get opened daily and on the foggy west side, where constant moisture accelerates corrosion inside the balance tube.
- A slider or door drags and needs a shoulder to move. The rollers have flat-spotted or the track has filled with grit and salt film. Roller failure is the number one reason a PGT sliding door gets replaced when the frame is still perfectly sound.
- Fog or condensation between the panes. The insulated glass unit’s perimeter seal has failed and moisture has entered the air space. Once that happens the unit cannot be dried out; the glass assembly gets replaced, not repaired.
- Water on the interior sill after rain. Weatherstripping, glazing gasket, or the sill seal has broken down. In San Francisco this shows up most in the Richmond and Sunset districts, where wind-driven rain finds every gap in a west-facing wall.
- A draft you can feel with the window closed, or a lock that won’t catch. The sash has dropped out of square or the lock keeper has shifted. Left alone, an out-of-square sash wears the balances and gaskets faster and turns a small adjustment into a full hardware replacement.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For San Francisco, plan on $5,310 – $17,700 for a typical window replacement and $9,440 – $29,500 when the unit is impact-rated. Those ranges cover the unit, the hardware or glass being replaced, labor, disposal of the old material, and sealing. A single balance or roller swap sits at the low end. A failed insulated glass unit or a full sash replacement pushes toward the middle. Impact-rated WinGuard glass and door panels with heavy hardware push toward the top.
What moves the number: the size and series of the unit, whether it’s impact-rated, how accessible the window is (a third-floor Victorian on a narrow lot takes more setup than a ground-floor slider), and whether the opening needs any repair once the old unit comes out. We quote line by line, upfront, with no change orders and no surprise add-ons. Every installation we do is backed by our 730-Day Done Right Promise. If it’s not done right, we make it right.
DIY or Call Us?
You can safely check a lot of this yourself. Look for the PGT label, measure the sash, photograph the balance or roller, test whether the sash is square in the frame, and note where water is showing up. That information makes the repair faster and the quote tighter.
Where it goes wrong is when a homeowner forces a stuck sash, pries at a balance tube, or tries to reset impact glass by hand. PGT balances are under real tension, and a released balance can whip out of its channel. Impact units are heavy and the glazing system has to be reseated and sealed correctly or the unit fails again within a season. We send background-checked, uniformed technicians who have up to 12 years of experience with these systems. Call (866) 320-2646 to schedule a free estimate.
FAQs
Plan on 20 to 25 years for the frame and sash and 10 to 15 years for seals, gaskets, and balances in our marine climate. The salt air and constant fog on the west side shorten that; a sheltered east-facing unit often runs longer. When a seal or balance goes before the frame does, replacing that part is the economical call. Call (866) 320-2646 for an exact quote, and estimates are free.
Often, yes. Balances, rollers, sash locks, and weatherstripping are all replaceable on their own, and that’s the right move when the frame and glass are sound. A failed insulated glass unit or a cracked impact pane gets replaced as a glass assembly, not repaired. We’ll tell you honestly which one you’re looking at before any work starts. Call (866) 320-2646 to schedule your free estimate.
Most single-part repairs finish in one visit, and a full window or door replacement typically takes a few hours per unit. Larger jobs or multiple impact units get scheduled across a longer window. We give you the timeline upfront and hold to it. Call (866) 320-2646 to get yours on the calendar.
We match the part to your exact PGT series using the label and on-site measurements, then order from PGT or a vetted supplier, with OEM parts for anything that drives sash movement. We don’t guess at sizes and we don’t substitute a part that “should” fit. Call (866) 320-2646 to schedule a free estimate, and a live person answers, 24/7.
When your PGT windows or doors stop working the way they should, the fix is usually smaller and more precise than you’d expect. We also work with KraftMaid, Cambria, and Silestone on the interior side of your home, so the same crew you trust with your windows can handle the rest of the project. For a same-week assessment and a straight, line-item quote, call Groundwork Construction Co. of San Francisco at (866) 320-2646 and schedule your free estimate.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.