A Groundwork company - serving San Francisco, CA

Schluter Kitchen Remodeling in San Francisco, CA

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Kitchen Remodeling: The San Francisco Owner’s Guide

Schluter kitchen remodeling in San Francisco typically runs $16,520 – $53,100 installed, depending on kitchen size, tile scope and whether we’re correcting a failed substrate. We work with Schluter products as an independent contractor, including KERDI waterproofing, DITRA uncoupling membranes and the SCHIENE and JOLLY trim profiles that finish tile edges. That range holds whether you’re rebuilding one failed tile field or starting a full kitchen.

Call (866) 320-2646

Most San Francisco owners discover the problem through cracked grout lines or a hollow thud underfoot long before they know a Schluter part is behind it. In older Inner Sunset and Richmond District homes, we see it after a slow leak has already softened the subfloor under the membrane. A popping tile near the dishwasher usually means the waterproofing gave out first, not the tile.

Which Schluter Models This Applies To

Schluter’s kitchen lineup isn’t one product; it’s a system, and getting the right piece means matching the profile to the job. The most common under-tile layers are DITRA (uncoupling membrane), DITRA-HEAT (membrane with heating cable), and KERDI or KERDI-BOARD for waterproofing. Edge trim comes in the SCHIENE, JOLLY, QUADEC and RONDEC families, sized by tile thickness, usually in millimeters. A 3/8-inch tile calls for a different profile than a 1/2-inch one, and using the wrong size is the single most common failure we’re called to fix.

Identifying your part: measure your tile thickness with a caliper, then check the profile’s printed size on the cardboard sleeve or the stamped impression on the trim itself. Older installations may carry discontinued SKUs or imperial sizes that Schluter has since shifted to metric. That’s where the OEM-versus-aftermarket decision matters. For waterproofing and uncoupling membranes, use genuine Schluter – the fleece backing and grid construction are what carry the warranty, and copycat membranes don’t match it. For edge trim, a quality anodized aluminum or stainless equivalent from a brand like Schluter or a certified alternative will hold up, but verify the exact millimeter size against your tile.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Kitchen Remodeling Is Failing

  • Hollow-sounding tile across a wide area. DITRA has debonded from the subfloor, which usually traces back to a thinset mixed too dry or a slab that wasn’t prepped. Tap lightly with a plastic tool handle; a dull, drummy sound means the layer has separated.
  • Grout cracking in a straight line or grid pattern. That’s movement transferring through the tile because the uncoupling membrane isn’t doing its job. In San Francisco’s settled 1940s stucco-and-slab homes, this pattern tracks with foundation movement the membrane was meant to absorb.
  • Water staining or a musty smell at a seam. KERDI banding wasn’t overlapped correctly at a penetrations point, or the sealant failed at a corner. Look at the seams around the sink, dishwasher, and floor-to-wall transitions first.
  • A raised or curled edge at SCHIENE or JOLLY trim. The trim was sized for a thinner tile and someone pushed it, or the mortar behind it dried before it set. This shows up as sharp edges catching a cloth or a bare foot.
  • Loose transition where tile meets a cabinet or island. Movement at the joint from a missing or compressed backer rod under the profile. It’s cosmetic at first, then it lets water in.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Replacing a failed Schluter kitchen layer in San Francisco falls within our $16,520 – $53,100 installed kitchen remodel range; if the job is scoped to a smaller tile field it lands closer to the small-kitchen figure of $10,620 – $23,600. Backsplash-only work runs $945 – $2,950; a kitchen island install is $3,540 – $11,800. Tile repair around a failed trim or a small membrane swap is part of a broader remodel quote, not a standalone line.

What drives the range: the square footage, whether the old membrane must be ground out or can be oversealed, whether the subfloor needs leveling, and whether DITRA-HEAT is going in. Our quotes are line-item and fixed. The number you see is the number you pay, no change orders for the prep work that surfaces mid-job. Every Schluter install carries our 730-Day Done Right Promise – if the membrane, trim or tile fails within that window due to workmanship, we make it right.

DIY or Call Us?

You can safely check some things yourself: tap the tile for hollow spots, look at the seams around the sink and dishwasher, measure tile thickness to confirm the profile size. That’s diagnostic, not repair.

Where DIY goes wrong: Schluter systems depend on thinset consistency, membrane overlap tolerance, and drying time that a weekend tile set doesn’t respect. A homeowner who reseals a KERDI corner over a wet substrate traps moisture and grows mold; a homeowner who re-trims a SCHIENE edge with construction adhesive leaves a profile that curls within a season. The failure compounds, and the repair gets more expensive. For finished tile and waterproofing work, call a trained installer. Call (866) 320-2646 and we’ll tell you what we’re seeing from the photos and the symptoms.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch