Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Windows & Doors: The San Francisco Owner’s Guide
We install and service Schluter windows and doors in San Francisco, and the installed price lands in the $5,310 – $29,500 range depending on scope, product line, and whether we’re talking a single unit swap or a full opening rebuild. Schluter window and door parts are specialist hardware, so we order to your specific model rather than pulling a generic piece off a shelf, which means scheduling in San Francisco is planned work, not a same-day call.
Owners usually find out something’s wrong the slow way. A sash that used to drop closed now needs a hip-check. The front door in a Noe Valley Victorian starts dragging on the threshold in June and stops by August. A splash of fog-driven rain shows up on the interior sill after a February storm. By the time the hardware is visibly failing, it’s usually been binding for a season or two, and the part has already taken wear it didn’t need to. Identifying the model and the failing component first is what keeps a small parts job from turning into a whole-unit replacement.
Which Schluter Models This Applies To
Schluter’s window and door hardware turns up across their tilt-and-turn and casement lines, and the part numbers are model- and generation-specific. A multi-point lock gearbox for a tilt-turn sash isn’t interchangeable with the surface-mounted hardware on an older casement, and hinge sets changed body dimensions between production runs. The fastest way to identify what you have is on the unit itself: open the sash or leaf and look for the manufacturer’s identification plate on the top or side edge of the frame, usually a sticker with a model code and a production date. Photograph it before you do anything else. That plate, plus a tape measurement of the sash width and height and the hinge or lock spacing, is what lets us match the part.
Then there’s the OEM-versus-aftermarket decision. For Schluter specifically, lock gearboxes and hinges are worth going OEM – the tolerances are tight, and a cheap knockoff gearbox that’s two millimeters off will bind, chew the strike plate, and sometimes crack the sash corner within a year. Seals, weatherstripping, and sill components are a different story: quality aftermarket equivalents hold up well here and save real money. We’ll tell you which is which for your unit. Grundwork Construction Co. of San Francisco is an independent service provider and not affiliated with Schluter, so our advice is about what works, not what’s branded.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Windows & Doors Is Failing
- The door or sash drags or binds at the threshold. Usually a worn hinge or a sagging hinge-side settling, common in older San Francisco frame construction where the building has moved over the decades and the hardware is compensating.
- You can’t get a multi-point lock to engage cleanly. The gearbox is worn or the door has shifted out of square, and the shoot bolts no longer line up with their keeps. Forcing the handle accelerates the wear.
- Drafts or a wet interior sill after rain. Failed weatherstripping, a worn sill seal, or a seal that’s simply aged out. In San Francisco’s fog belt this shows up as persistent condensation and damp sills more than obvious drafts.
- The operating handle feels loose, gritty, or won’t return to center. An internal gear or latch mechanism is wearing out. Continuing to operate it feels like it’s grinding because it is.
- Visible cracks near hinges or the lock keep. The frame or sash material itself is fatiguing, often from years of hardware fighting a misalignment. This one is worth looking at before it becomes a glass or sash replacement.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For reference, here are our installed ranges for the work these parts sit inside, so you can see where your job likely falls:
| Scope | Installed Price Range (San Francisco) |
|---|---|
| Hardware and part replacement within an existing unit (hinges, gearbox, seals, sill components) | $250 – $900 per unit, parts and labor |
| Window replacement (full unit) | $5,310 – $17,700 |
| Impact window installation | $9,440 – $29,500 |
What drives the range: the model and whether the part is OEM, the number of units, whether the frame has shifted and needs realignment, and glass if the failure went that far. We quote parts and labor as separate line items, so you see exactly what the part costs and what the installation costs. Upfront pricing, no surprises – the number you see is the number you pay. Workmanship is covered by our 730-Day Done Right Promise, and if it’s not done right, we make it right. Estimates are free.
DIY or Call Us?
Some checks are genuinely safe and useful for an owner to do. Photograph the ID plate, measure the sash and hinge spacing, clean and lubricate the hinges and lock mechanism with a silicone-based product (not WD-40, which attracts grit), and adjust the strike plate screws a quarter turn at a time to see if a dragging door frees up. That’s diagnostic work, and it often tells you whether you need a part at all.
Where DIY goes wrong on Schluter hardware: multi-point lock gearboxes and hinge sets are precision assemblies, and a wrong-size replacement or a mis-seated gearbox can crack a sash corner or leave you with a door that won’t secure – a real problem in San Francisco, where a front door that won’t lock is a security issue, not an inconvenience. If the handle won’t engage or the frame is cracked, stop and call. We’ll schedule a look and give you a written quote. Call (866) 320-2646.
FAQs
Quality hinges and multi-point gearboxes typically run 10 – 15 years with normal use, and weatherstripping and sill seals often go sooner at 5 – 10 years. San Francisco’s salt air and fog accelerate seal degradation, so coastal-facing units tend to need seals replaced earlier than inland ones. If yours is past that window and binding, it’s worth a look. Call (866) 320-2646 for an exact quote – estimates are free.
Sometimes yes – a hinge adjustment, a strike-plate shim, or a fresh seal set often solves a binding or draft without a new part. Worn gearboxes and cracked hardware generally can’t be reliably repaired and need replacement. We’ll tell you honestly which situation you’re in before quoting anything.
Most single-unit hardware and seal replacements are done in a single visit, typically a couple of hours per unit once the correct part is on hand. Because Schluter parts are model-specific and we order to your unit, the lead time to get the part is usually the long pole, not the install itself. We’ll give you a realistic schedule up front.
We match the part to your unit’s ID plate and measurements, then source OEM where it matters (locks, hinges) and a vetted aftermarket equivalent where it doesn’t (seals, sill components). We don’t carry a parts inventory – every part is ordered for your specific model, which is why accuracy on the identification plate matters so much. Call (866) 320-2646 and have that photo ready.
If you’ve got a Schluter window or door that’s binding, leaking, or won’t secure, call (866) 320-2646 for a free estimate. We answer with a live person 24/7, our technicians are background-checked and uniformed, and we bring the same upfront pricing to a parts job that we do to a full window replacement – with the 730-Day Done Right Promise behind the work. We also work with KraftMaid, Cambria, and Silestone on the interior side of these projects if your window work is part of a larger remodel. From foundation to finish line, built to last, backed in writing.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.