Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Silestone Windows & Doors: The San Francisco Owner’s Guide
We install and replace Silestone-compatible windows and doors in San Francisco, and most single-unit swaps run $5,310 – $17,700 for standard window replacement or $9,440 – $29,500 for impact-rated units, depending on size, frame material and glazing. Owners usually find the failure before they see it: a sash that won’t latch in the fog belt, a door that swells shut after a rainy week, or condensation trapped between panes that never clears. Groundwork Construction Co. of San Francisco is an independent service provider, not affiliated with Silestone, and we price the part and the labor as separate line items so you can see exactly what you’re paying for.
Which Silestone Models This Applies To
Silestone’s window and door hardware comes in a handful of product families, and the part you need depends on which one is in your wall. The two you’ll meet most in San Francisco homes are the tilt-and-turn casement series and the standard sliding patio door line. The tilt-and-turn units use a specific corner gasket and handle spindle length that a generic replacement won’t seat correctly; the sliding doors run on a roller and track combination sized to the panel weight, and swapping in an undersized roller is the most common callback we fix.
To identify the right part, start at the unit itself. There’s usually a manufacturer label on the top or side of the frame, or etched into the glass edge, showing the series code, the date code and the glass spec. Measure the visible glass, the frame depth and the hardware hole spacing with a tape before you order anything. On the OEM-versus-aftermarket question for Silestone specifically: the original hardware fits without modification and holds the factory seal, while quality aftermarket equivalents can cost 30% to 50% less and work fine for high-wear parts like rollers and weatherstripping. For structural components and gaskets that carry the weather seal, we lean OEM. A compatibility gotcha worth knowing: Silestone changed its tilt-and-turn handle spindle length partway through the series, so two units that look identical from the room can take different handles. Check the date code before you buy.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Silestone Windows & Doors Is Failing
- Fogging between the panes that won’t clear. The insulated glass seal has failed and moisture is trapped inside the unit. In San Francisco’s coastal fog, this happens faster than inland because the daily temperature swing works the seal harder. A single-pane swap or full unit replacement fixes it; wiping the glass never will.
- The sash won’t latch or lock. Usually a worn keeper, a sagging hinge or a strike plate that has shifted out of alignment. If the latch won’t catch, the unit no longer seals, and that’s a security and weather problem at the same time.
- The door drags or sticks seasonally. Wood and composite frames move with humidity, and a door that swells shut after rain and frees up in dry weather points to a frame or hinge issue, not just a swollen panel. Left alone, the dragging wears the weatherstripping and the threshold.
- Air or water coming through the frame. Failing weatherstripping, a cracked gasket or a gap at the sill. This is the one that shows up on the energy bill and, in a heavy storm, as water on the floor.
- The roller or track is grinding on a slider. Flat-spotted rollers, a bent track or debris in the channel. A grinding slider will eventually jump the track, and a jumped panel is a real injury risk if someone tries to lift it back into place.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in San Francisco for Silestone-compatible window and door work runs $5,310 – $17,700 for standard window replacement and $9,440 – $29,500 for impact-rated installation. A single hardware or gasket fix sits at the low end; a full unit replacement with new framing and flashing sits at the high end. What drives the range: unit size, frame material, glazing spec, whether the opening needs reframing, and how high up the wall it sits. Third-story work near the Marina or on a steep Noe Valley lot takes more labor and more safety setup than a ground-floor slider.
We quote parts and labor as separate line items. The number you see is the number you pay, and it doesn’t move once work starts. Every install is covered by our 730-Day Done Right Promise, and we pull the permits and pass the inspections the work requires. Pricing in San Francisco also reflects the city’s permit and inspection costs, so a quote that looks cheap usually left those out.
DIY or Call Us?
You can safely check a few things yourself: measure the glass and frame, read the label for the series and date code, and tighten or clean a sliding door track. What goes wrong with DIY on this part is the swap itself. Replacing a sealed unit or a structural gasket requires getting the weather seal right, and a bad seal on a San Francisco window means water intrusion within a season. Lifting a heavy slider panel back onto a bent track is where people get hurt.
If your unit is above the first floor, or the failure involves the seal or the track, that’s a job for a trained technician. Call (866) 320-2646 and we’ll give you a free estimate on the part and the install, with the price in writing before anyone touches the wall.
FAQs
A quality unit should give you 20 to 30 years of service, but the coastal fog belt shortens the glass seal life, so expect fogging between the panes somewhere in the 12-to-18-year range on the west side and outer Sunset. Hardware and weatherstripping wear faster than the unit itself and often need replacing well before the glass does. Call (866) 320-2646 for a free estimate on whether a part swap or a full replacement makes sense for your unit.
Often yes. A stuck latch, a worn roller, a cracked gasket or a dragging hinge is usually a part-level repair, not a full unit replacement, and we’ll tell you plainly which one you’re looking at. Fogging between the panes is the exception: once the seal fails, the unit needs replacing, because the moisture is inside the glass. Call (866) 320-2646 and we’ll give you the honest call between repair and replace.
A single hardware or gasket replacement is usually a short visit, and a full window or door unit replacement typically takes a few hours to most of a day per opening, depending on size and whether the opening needs reframing. Most of our jobs are finished in a single visit. Call (866) 320-2646 for a free estimate and a realistic timeline for your San Francisco home.
We match the part to your unit’s series code and date code before ordering, then source it through our brand partners and specialty suppliers. We don’t carry parts on a truck and we don’t stock locally, so the match happens against your specific model, not a guess off a shelf. We also service KraftMaid, Cambria and Kohler across other trades. Call (866) 320-2646 to get your part matched and a free estimate scheduled.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.