Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Home Additions & ADU: The San Francisco Owner’s Guide
We build home additions and ADUs in San Francisco that are detailed to work with TAMKO shingle systems on the roof and TAMKO waterproofing underlayments on low-slope transitions, and installed additions of this scope typically run $53,100 – $153,400 depending on square footage and site. Detached or fully permitted ADUs run $106,200 – $259,600. Groundwork Construction Co. of San Francisco is an independent contractor and is not affiliated with TAMKO. Most owners don’t call us because a “part” failed; they call because a finished addition or ADU that should have been built to a TAMKO roof spec is now leaking at the tie-in, shedding granules into a new gutter run, or failing an inspection over missing underlayment documentation. That’s the part that failed: the roof assembly, not the framing.
Which Tamko Models This Applies To
The TAMKO products that matter in a San Francisco addition or ADU are the roof-system components, and there are three families you’ll see on a real spec sheet: TAMKO Heritage laminated asphalt shingles (the common one on pitched addition roofs in neighborhoods like Noe Valley and the Sunset), TAMKO MetalWorks steel shingles and shakes for owners who want a longer service life, and TAMKO TW underlayments plus TAMKO Waterproofing Membrane for the low-slope sections that additions and ADUs almost always create where a new roof meets an existing one.
Identify what you actually have before anyone quotes you a number. Check two places: the pitch of the new roof (Heritage is a pitched-roof product, MetalWorks and TAMKO underlayments cover the flatter transitions) and the paper trail from the permit set, which lists the shingle manufacturer and product line on the roofing schedule for a permitted San Francisco addition. Without that, the reliable method is a physical inspection of a shingle tab or a membrane seam, not a guess from the color.
On OEM versus aftermarket: TAMKO Heritage is a laminated shingle with a specific exposure and nail-zone spec, and generic field shingles are not a safe substitute at a tie-in or at a valley. Accessories are a different story. Ventilation, drip edge, and flashing metal do not have to carry the TAMKO name, and we’ll say so plainly. What does have to match is the shingle system and the underlayment system, together, because mixing them is how a five-year-old addition roof starts leaking in a San Francisco winter. We also work alongside KraftMaid, Cambria, and Silestone on the interior finish packages that sit inside these additions, so the same crew story carries through the whole project.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Home Additions & ADU Is Failing
- Water staining on the new interior ceiling near the roofline where the addition meets the original house. This usually points to a failed or missing membrane at the transition, not a bad shingle. On a San Francisco addition, that low-slope tie-in is where most leaks start.
- Granules in the gutter or on the new walkway below the addition roof. TAMKO Heritage shingles shed a little early; heavy granule loss within the first few years usually means the shingles were installed below the manufacturer’s minimum pitch without the right underlayment beneath them.
- Curling or lifted shingle tabs along the new roof’s perimeter and ridge. Poor attic ventilation in a tightly built ADU traps heat and moisture, and shingles cupping at the ridge are the first visual sign. San Francisco’s cool, damp air makes this worse when ventilation is undersized.
- Bubbling or delamination on the TAMKO membrane over the ADU’s low-slope section. Adhesion failure at the seam, often from surface prep skipped during the original build, and it will spread if the seam is patched over instead of replaced.
- Failed inspection notes citing missing underlayment or roof-schedule documentation for the addition. A permitted San Francisco addition has to match its permit set, and a roof that was value-engineered after the permit was pulled will show up at final inspection.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Rebuilding the failed roof assembly on an existing San Francisco addition or ADU, including tear-off, new TAMKO underlayment, TAMKO Heritage or MetalWorks shingles, and a corrected tie-in, typically runs $9,440 – $23,600 for the roof portion, and a metal roof upgrade on the same addition runs $17,700 – $47,200. A full home addition install is $53,100 – $153,400, and a ground-up ADU is $106,200 – $259,600. Your exact range depends on square footage, whether the tie-in to the original house is a low-slope transition, and how much existing roof has to come off.
Our pricing is upfront, and the number you see is the number you pay. Every project is covered by the 730-Day Done Right Promise, so if the tie-in or the shingle system fails the way the last one did, we make it right. Calls are answered by a live person, 24/7. Call (866) 320-2646 for a free estimate and written line-item quote.
DIY or Call Us?
You can safely walk the ground around your addition, look in the gutters for granule buildup, check the interior ceiling for staining after a storm, and pull the permit set to see what the roof schedule actually specified. That’s useful and worth doing.
What you shouldn’t do is repair a TAMKO shingle system, a membrane seam, or a roof tie-in yourself. Pitched roof work is a fall hazard, and a low-slope membrane that isn’t properly adhered and flashed will leak again the next rainy season in San Francisco, often worse than before because it hides water inside the addition wall. Call (866) 320-2646 and we’ll come look at it and tell you honestly what’s failed and what it costs to fix. Estimates are free.
FAQs
A properly installed TAMKO Heritage roof on a pitched addition in San Francisco should give you 25 to 30 years, and TAMKO MetalWorks shingles stretch well past that. The TAMKO underlayment and membrane at the low-slope tie-in is the shorter-lived part, and in San Francisco’s damp air you should have it inspected every 5 to 7 years. Call (866) 320-2646 for an inspection quote.
Sometimes, yes. A single failed flashing at the tie-in or one delaminated membrane seam can be repaired if the surrounding system is still sound. If the shingles are lifting across the whole perimeter or the membrane is failing in multiple places, patching is throwing money at a problem that comes back. We’ll tell you which one you’re facing, and the estimate to find out is free.
Replacing the roof assembly on an existing addition or ADU usually takes a few days once materials are on site, depending on square footage and how much of the tie-in needs rebuilding. A full new addition or ADU build is a multi-month permitted project in San Francisco, and we’ll give you a written schedule before any work starts.
We source TAMKO Heritage, MetalWorks, and the TW underlayment and waterproofing membrane lines through verified supplier channels matched to your permit set and your roof’s actual pitch. We don’t stock parts and we don’t carry inventory, but we order to your project spec and confirm the product line in writing before installation. Call (866) 320-2646 to start a free estimate.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.