A Groundwork company - serving San Francisco, CA

Tremron Home Additions & ADU in San Francisco, CA

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Tremron Home Additions & ADU: The San Francisco Owner’s Guide

We build and finish home additions and ADU projects in San Francisco using Tremron hardscape and masonry products, installed at $53,100 – $153,400 for a home addition and $106,200 – $259,600 for a full ADU, with free estimates scheduled around your timeline rather than a same-day promise nobody can keep on a project this size. Most owners don’t start by asking about a part. They start with a symptom: a patio slab at the new addition’s rear entry that heaves or drops a quarter inch within a year, a retaining wall face that spalls after its first wet season, or grout lines in a Tremron paver apron that open up because the base underneath was never compacted to spec. That’s usually when the call comes in, and it’s the right call to make.

Call (866) 320-2646

One thing worth saying plainly: Groundwork Construction Co. of San Francisco is an independent service provider. We’re not affiliated with Tremron, and we don’t claim to be. What we do is install Tremron products correctly, diagnose the failures that come from poor base prep and drainage, and stand behind the work with our 730-Day Done Right Promise.

Which Tremron Models This Applies To

Tremron makes a wide line of pavers, retaining wall blocks, and caps, and the part that matters on an addition or ADU project is rarely the surface unit itself. It’s the base course, the edge restraint, the polymeric joint sand, and the wall’s drainage aggregate and geogrid. Tremron paver profiles differ by series, and thickness is the number you need first: most Tremron driveway and patio pavers run 60mm or 80mm, and the 80mm units are the ones spec’d for vehicle loads and for the transition apron where a new addition meets an existing slab. Getting a 60mm paver where an 80mm was called for is one of the most common compatibility mistakes we correct.

To identify what you have, pull a loose unit and measure thickness with a caliper, not a tape measure. Check the underside for the manufacturer stamp and any series marking. Photograph the face pattern and the color name if you can find it on the original invoice. Tremron colors are batch-dyed, so a replacement run from a different lot can read a shade off in raking afternoon light; on a San Francisco west-facing patio, that mismatch is visible every day from 3pm on.

The OEM-versus-aftermarket decision is straightforward here. Tremron-branded units match dimension, thickness, and color family, which matters on visible faces. For hidden work, meaning base rock, drainage gravel, geotextile, and polymeric sand, a quality equivalent is fine and often what a good installer would choose anyway. Our technicians have up to 12 years of experience matching product to the specific assembly, and we tell you which is which before anything gets ordered.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Tremron Home Additions & ADU Is Failing

  • Heaving or settling at the addition’s threshold. The paver apron lifts or drops where the new slab meets the existing house. This almost always traces to a base that wasn’t excavated deep enough or compacted in lifts, and San Francisco’s clay-heavy soils in neighborhoods like Noe Valley and the Inner Sunset make it worse when water has nowhere to go.
  • Spalling or flaking on a retaining wall face. The block face chips and sheds. Freeze-thaw isn’t the culprit here; saturated block that never drains is. Missing weep holes or a blocked drainage gravel column behind the wall traps water inside the assembly.
  • Joint sand washing out after rain. Polymeric sand erodes from between pavers within a season or two. Either the sand was applied to a wet surface, the joints weren’t filled to full depth, or the surface isn’t draining toward the outlet it was supposed to.
  • Wall rotation or bulging. The wall leans out of plumb, usually at the top courses. That’s a geogrid or tie-back problem, and it’s the one failure on this list you shouldn’t ignore for a season. A leaning wall above a walkway is a real hazard.
  • Efflorescence that keeps returning. White mineral bloom on the paver or block face that you clean off and it comes back. It’s moisture moving through the unit from behind, which points at drainage, not at the surface.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For San Francisco, a home addition runs $53,100 – $153,400 and a full ADU runs $106,200 – $259,600 installed. A garage conversion, which is the route many San Francisco owners take first, runs $35,400 – $94,400. If the scope is really a hardscape repair, paver patio work runs $4,130 – $12,980 and a paver driveway runs $8,260 – $21,240. Those are installed numbers, not material-only.

What moves you within a range: square footage, whether the site has rear-yard access for equipment, soil conditions and how much over-excavation the base needs, drainage corrections, and whether the existing assembly has to come out first. San Francisco hillside lots on the eastern slope often need more retaining structure than a flat-lot project of the same size.

Upfront pricing, no surprises, means you get a written line-item quote that separates product, base prep, drainage, and labor. Nothing gets bundled into a single number you can’t audit. If a change order is needed, you approve it in writing before we proceed. All of it sits under the 730-Day Done Right Promise, and we offer 0% financing for 18 months plus $1,000 off projects over $10,000.

DIY or Call Us?

Some of this you can check yourself, and should. Walk the perimeter after a heavy rain and look for ponding. Measure the wall’s plumb with a level at three points. Pull one loose paver and check the base depth. Photograph the joint sand condition. Those observations will make any conversation more useful.

Where DIY goes wrong is the part you can’t see. Rebuilding a retaining wall base, re-compacting subgrade in lifts, and re-establishing drainage on an assembly that’s already failed is heavy, structural work, and a wall that leans over a walkway or a neighbor’s property line is a genuine safety issue, not a cosmetic one. An improperly tied-back wall can fail suddenly. Pulling the base out from under an addition’s threshold can also undermine the slab it supports. That’s the point where a trained crew matters more than a weekend.

If you’ve got a Tremron assembly showing any of the symptoms above, call us at (866) 320-2646 and we’ll schedule a free estimate. A live person answers, 24/7, so you’re not leaving a message and waiting until Monday.

FAQs

How long should a Tremron paver or wall assembly last in San Francisco? A properly built assembly should hold 25 to 30 years on the paver surface itself. The failure point is almost never the unit; it’s the base and the drainage. A paver that’s 15 years old over a well-compacted, well-drained base will outlast a new install over a bad one. Call (866) 320-2646 for an exact assessment, free of charge.

Can it be repaired instead of replaced? Often, yes. Re-sanding joints, resetting a localized area of pavers, and restoring drainage behind a wall solves most of what we see. Full replacement usually only comes up when the base itself is wrong or a wall has rotated past the point where re-facing works. We’ll tell you which one you’re looking at in the estimate, not after the work starts.

How long does the work take? A hardscape repair is typically a few days. A home addition or ADU is a months-long project with permitting, and San Francisco permitting on ADUs adds real time to the front end. We give you a realistic schedule in the written quote and flag the permit review window before you commit.

How do you source the right Tremron product? We confirm thickness and series from a pulled unit and the original invoice where it exists, then order to match. We don’t stock Tremron parts and we don’t carry them on a truck, so lead time is part of the schedule. If your assembly needs KraftMaid, Cambria, or Silestone work elsewhere in the project, we handle that through the same coordination.

Will the price change once work starts? Not without your written approval. Upfront pricing means the number in the quote is the number you pay unless you approve a scope change. Call (866) 320-2646 to get that quote scheduled. Estimates and design consults are free.

Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch