A Groundwork company - serving San Francisco, CA

Unilock Fence Installation in San Francisco, CA

FenceFence
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Unilock Fence Installation: The San Francisco Owner’s Guide

A Unilock fence installation in San Francisco typically runs $4,130 to $10,620 installed, and most straightforward runs are finished in one to three days depending on footage and site access. If you’re here, you probably have a fence line that’s leaning, a post that’s shifted, or a wall section that’s cracking at the base after a wet winter. Unilock is a paving and hardscape brand, so what you’re pricing is a Unilock wall or pillar system used as a fence foundation, with panels or rails mounted to it. That detail matters, and it’s where most bids go sideways.

Call (866) 320-2646

Key Takeaways

  • Installed range for San Francisco: $4,130 to $10,620, driven mostly by footing depth, footage, and hillside grading.
  • Unilock systems are modular hardscape units, so “the part” is usually a base course, cap unit, or footing, not a single component.
  • Live person answers our line 24/7, and every job is covered by our 730-Day Done Right Promise.

Which Unilock Models This Applies To

Unilock makes segmental retaining wall and pillar systems – the Brussel Wall, the Brussels Dimensional System, and pillar kits built from the same units – and homeowners commonly mount wood, composite, or aluminum fence panels on top of them. That’s a legitimate way to build a fence in San Francisco, especially on sloped lots in Noe Valley and Bernal Heights where a post-in-dirt fence will eventually walk downhill. The compatibility gotcha: caps and coping units are sized to specific wall series, and a cap from one series won’t seat cleanly on another. Measure the exposed face of your wall block and the cap depth before you order anything, and check for a mold stamp on the underside of a loose unit.

On the OEM question, Unilock units are sold through authorized hardscape dealers, not through us. We’re an independent installer and not affiliated with Unilock. We match the correct series and color blend by measurement and photo, then source through local dealers. Aftermarket equivalents exist, but color lots drift between production runs, so mixing a new unit into an existing wall often shows. Ask about a blended approach when a full-match unit isn’t available.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Unilock Fence Installation Is Failing

  • Posts leaning after heavy rain. Footings were set too shallow or the soil wasn’t compacted, and San Francisco’s clay-heavy soils swell and shift seasonally. Once a post moves, the panel load pulls the whole run out of plumb.
  • Hairline cracks running through wall units. Usually a base course that wasn’t set on compacted gravel, so the wall flexes under load. Cracks that track the same line across several units point to foundation movement, not a bad block.
  • Caps rocking or lifting. Adhesive failure or a cap sized for a different series. You’ll notice it when water gets behind the cap and freezes or sits – common on north-facing walls that stay damp through the fog season.
  • Rust bleeding at panel brackets. Standard fasteners corroding in salt air, which is a real problem west of Twin Peaks and anywhere within a mile of the ocean. Stainless hardware is the fix, not a paint touch-up.
  • Wall bulging outward at mid-height. Missing geogrid reinforcement or backfill that wasn’t drained. A bulging wall is a structural warning, not cosmetic, and it gets worse with every wet season.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Expect $4,130 to $10,620 installed for a Unilock-based fence in San Francisco. The low end covers a short, level run with an existing sound footing. The high end covers hillside grading, deeper footings on a sloped lot, geogrid reinforcement, and stainless hardware in a coastal exposure zone.

Line item Typical range
Unilock wall or pillar units plus caps $1,400 – $3,900
Fence panels, posts, and hardware $1,100 – $3,200
Excavation, footing, and drainage $900 – $2,400
Labor and site protection $730 – $1,120

We quote line by line before work starts, so the number you see is the number you pay. Workmanship is covered by the 730-Day Done Right Promise. If it’s not done right, we make it right.

DIY or Call Us?

You can safely check a few things yourself: confirm the wall is plumb with a level, look for water pooling at the base after rain, and photograph any cracked units with a tape measure in frame so the series can be identified. What you shouldn’t do yourself is reset footings or rebuild a bulging wall. A retaining wall holding back soil carries real load, and an unreinforced rebuild can fail suddenly. On sloped San Francisco lots the failure mode is worse, because a wall that lets go can take the fence and part of the grade with it. That’s a job for a trained crew with the right compaction and drainage detail. Call us at (866) 320-2646 and we’ll walk you through what’s actually failing and what a fix costs. Alongside Unilock and hardscape work, we install products from KraftMaid, Cambria, and Silestone on other projects.

FAQs

How long does a Unilock fence installation last in San Francisco? A properly footed Unilock fence wall typically holds up 25 to 40 years in this climate, with the caveat that coastal salt exposure shortens the life of metal hardware and fasteners well before the block itself. Stainless hardware is the difference maker near the ocean.

Can it be repaired instead of replaced? Often yes. A single leaning post, a loose cap, or isolated cracked units can usually be reset or swapped without rebuilding the whole run. If the wall is bulging or the cracks track across the base, a partial rebuild is the honest answer. Call (866) 320-2646 for a free estimate and we’ll tell you which one you’re looking at.

How long does the swap take? Most Unilock fence installs are done in one to three days, with footing cure time factored in. Hillside grading or a wall rebuild pushes that to a week or more. We schedule the work, not a same-day promise, and we tell you the real timeline up front.

How do you source the part? We identify your series by measurement and photo, then order through authorized Unilock hardscape dealers in the Bay Area and match the closest color blend available. Where production lots have drifted, we’ll show you samples so the match is your call before anything is delivered.

Call Groundwork Construction Co. of San Francisco at (866) 320-2646 to schedule your free estimate. Live person, 24/7, upfront pricing, no surprises.

Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch