A Groundwork company - serving San Francisco, CA

Unilock Home Additions & ADU in San Francisco, CA

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Unilock Home Additions & ADU: The San Francisco Owner’s Guide

A Unilock-compatible home addition or ADU in San Francisco typically runs $53,100 to $153,400 for the addition side and $106,200 to $259,600 for a full ADU, and we install these systems for owners across the city. Most owners don’t find out something failed until they see it: a hairline crack opening across a modular wall panel, a footing that settled differently than the rest of the structure, or a panel seam pulling apart after a wet winter. By the time it’s visible, the underlying cause (usually water intrusion or soil movement) has been working for a season or more. We treat the diagnosis as seriously as the build.

Call (866) 320-2646

Which Unilock Models This Applies To

Unilock’s system lines are modular, which is good news and bad news. Good, because replacement components are dimensionally standard. Bad, because the wrong series part will physically fit and still fail. The practical split most San Francisco homes fall into:

  • Wall and panel system parts – matched by panel thickness (commonly 4-inch to 8-inch profiles) and by the interlock profile stamped on the panel edge. Measure the panel, don’t guess from a photo.
  • Footing and base components – matched by load rating, not by appearance. A lighter-rated base part under a loaded corner is a recurring failure we clean up.
  • Trim and connection hardware – the least standardized and the most model-specific. This is where the OEM-versus-aftermarket decision actually matters.

Find the serial or series label on the panel edge, the footing plate, or the original install documentation before you order anything. On the OEM question: we use genuine Unilock components where the part carries structural load, and quality aftermarket equivalents where the part is cosmetic trim, because the cost difference is real and the failure risk is low. Where an aftermarket part is being sold as a drop-in for a load-bearing position, walk away. We’re an independent service provider and not affiliated with Unilock, which is exactly why we’ll tell you when a genuine part is the only responsible choice.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Unilock Home Additions & ADU Is Failing

  • Hairline cracks spreading across a panel face. Usually footing movement or a base component that compressed unevenly, not a defect in the panel itself. The crack is the symptom; the footing is the problem.
  • Water staining at panel seams after rain. A failed connection seal or a panel that shifted slightly out of profile. San Francisco’s wet winters find every seam that isn’t fully seated.
  • A door or window that no longer closes cleanly in the addition. Racking from differential settlement, which shows up at openings first because they’re the least forgiving part of the frame.
  • Soft or spongy feel at the base of a wall. Moisture has reached the footing or base component. This one doesn’t fix itself and gets more expensive the longer it runs.
  • Visible gap between the addition and the main house. Connection hardware loosening or corroding. On San Francisco hillside lots, this often tracks back to the original tie-in rather than the addition system itself.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Installed pricing for the work, not just the part:

Scope Typical Installed Range
Component or panel replacement (targeted repair) $4,130 – $12,980
Home Addition $53,100 – $153,400
Garage Conversion $35,400 – $94,400
ADU Construction $106,200 – $259,600

What drives the number: how much of the system has to come apart to reach the failed component, whether the footing needs remediation, and whether the part is genuine Unilock or a matched equivalent. We quote line-item, upfront, so you see the part cost and the labor separately. Every project is covered by our 730-Day Done Right Promise, and the quote you sign is the number you pay.

DIY or Call Us?

You can safely do the diagnosis: photograph the crack or seam, measure the panel thickness, find the series label, and note where the water is coming in. That’s genuinely useful and we’ll take it. What you should not do is disturb a footing, a load-bearing panel, or connection hardware on a structure that’s holding up part of your home. A compression failure under a loaded corner is a structural problem, and a homeowner working under a partially supported wall is how people get hurt. Most of the “replacement” calls that end badly started with someone trying to shim a settled footing on their own. Call us at (866) 320-2646 for a free estimate and we’ll tell you plainly whether it’s a repair or a rebuild.

FAQs

How long should a Unilock system last in San Francisco? A properly installed and footed Unilock addition system should give you 30-plus years, and we’ve seen well-built systems run well past that. The failure usually isn’t the part, it’s the footing and the water management around it, which is why we inspect both before quoting a replacement.

Can this be repaired instead of fully replaced? Often yes, and that’s the first thing we check. Targeted component and panel replacement starts around $4,130 where the failure is localized and the footing is sound. If the settlement runs under a load-bearing wall, a full replacement is the honest answer. Call (866) 320-2646 and we’ll diagnose it in person.

How long does the swap take? A targeted component replacement is usually a single visit, and most jobs are completed in one trip to the property. Larger panel or footing work runs several days depending on access and permit requirements through San Francisco’s Department of Building Inspection. The $1,000 off projects over $10,000 and 0% financing for 18 months both apply here.

How do you source the part? We match genuine Unilock components to your series label, sourced through Unilock’s distribution network, and we’ll use a verified aftermarket equivalent only on non-structural trim where the savings are real. We don’t stock parts and we don’t carry them on a truck. We also work with KraftMaid, Cambria, and Silestone on the interior side of ADU and addition projects.

When you’re ready to price the work instead of guessing at it, call (866) 320-2646 for a free estimate. Our technicians have up to 12 years of experience, they arrive background-checked and in uniform, and someone answers the phone any hour of the day. Upfront pricing, no surprises, from foundation to finish line.

Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (866) 320-2646
Local Service Coverage

Request a Free Estimate in San Francisco

Tell us what you need - Groundwork Construction Co. of San Francisco responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch