Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterCustom vs. Stock Kitchen Cabinets in San Francisco: The Geometry Problem Nobody Warns You About
Choose semi-custom cabinets unless your San Francisco kitchen has a genuine one-off layout that needs site-built millwork, or you’re flipping a rental and speed matters more than fit. Stock cabinets are sized for new construction on a 3-inch module. San Francisco kitchens were mostly framed before 1920, and the gap between those two realities ends up as an awkward 4.5-inch filler strip next to your refrigerator. In a city where kitchens are already tight, filler strips aren’t a finish detail. They’re a layout failure. For most Victorian and Edwardian kitchens here, semi-custom is the answer. Call (866) 320-2646 and we’ll tell you which tier your kitchen actually needs.
Why San Francisco Kitchens Rarely Fit Stock Cabinets
Victorian and Edwardian row houses on the west side and through the Mission and Noe Valley were built in an era of custom millwork. There was no module standard. Every cabinet was cut to the room. A century of settling later, that original geometry doesn’t line up with anything a factory ships.
Here’s what we run into on nearly every job:
- Ceiling heights from 8’2″ to 9’6″ in the same block, sometimes the same house.
- Wall runs that stop at 7’4″ or 9’11”, never the even increment stock expects.
- Corner angles of 87 or 93 degrees after decades of settling, not 90.
- Chimney breasts and old plumbing chases that punch a 14-inch notch out of a wall.
Stock cabinets can’t absorb any of that without visible filler. Semi-custom can, because it’s built in 3-inch increments with real modification options. And that’s the whole debate in this city: it’s usually geometry, not budget, that makes the call.
The damp doesn’t help. Marine fog and salt air off the Pacific push moisture into a kitchen near an exterior wall, and MDF-core stock boxes swell at the joints within 5 to 8 years. KraftMaid’s plywood-box construction resists that far better. In a city where a kitchen gets gut-renovated once per ownership period, maybe twice a century, construction quality is a 20-year decision you only get to make once.
The Three Real Tiers for San Francisco Homeowners
| Tier | What You Get | Installed Cost in San Francisco | Best For |
|---|---|---|---|
| Stock (IKEA, Home Depot) | Fixed sizes, filler-dependent, fast | $8,000-$14,000 | Newer condos, rentals, fast turnarounds |
| Semi-custom (KraftMaid) | 3-inch increments, modification options, plywood box | $15,000-$28,000 | Most Victorian and Edwardian kitchens |
| Full custom | Built to the inch, 12-20 week lead time | $30,000-$60,000+ | Odd geometry, high-end finishes, landmark homes |
Semi-custom wins because it clears the dimensional problem without the cost jump. KraftMaid builds in increments and modifications that let us close most of the gap between a 1904 wall run and a modern cabinet line. Full custom earns its price when the kitchen is truly one-off: a curved bay, a diagonal wall, a landmark property where every detail gets reviewed.
For a broader look at what fits into the full budget, our Kitchen Remodeling page covers the rest of the project scope. Cabinet installation alone typically runs $4,720-$15,340 in San Francisco. A full kitchen remodel lands between $16,520 and $53,100, and a smaller kitchen between $10,620 and $23,600.
Common San Francisco Scenarios
Noe Valley Edwardian with a chimney breast
That 14-inch notch throws off every stock run. Semi-custom fills the gap cleanly with a modified box inside the run. Stock leaves a visible seam you’ll notice every morning.
Inner Sunset kitchen against an exterior wall
Direct fog exposure means moisture. Plywood-box construction and stainless hardware hold up. Standard MDF-core boxes swell first at the joints.
Pacific Heights rental flip
Speed and payback matter more than perfect fit. Stock works fine when the buyer isn’t living in it and the layout is already new-build-friendly.
Richmond District landmark home
If the exterior or trim triggers review, custom shop-built cabinets in a matching profile are often the only route through the design review gauntlet.
West-side contractors learn fast to spec stainless and galvanized hardware on small jobs too, because salt and fog corrode standard fasteners and paint within a fraction of their normal lifespan. The same lesson applies inside a kitchen backing onto an exterior wall.
What the Installation Itself Demands
Out-of-square walls are almost guaranteed in an old San Francisco kitchen. Level, plumb, and shim isn’t optional. It’s the difference between a drawer that closes smoothly for 15 years and one that starts rubbing after two winters.
Our technicians have up to 12 years of experience, and every job is background-checked and uniformed. The whole install is covered by the 730-Day Done Right Promise. If drawer alignment, door swing, or box leveling slips after we leave, we come back and make it right. That’s two full years on the details that fail first in an old house.
Pricing is upfront. The number you see is the number you pay. And with 0% financing for 18 months plus $1,000 off projects over $10,000, the gap between the stock and semi-custom tiers usually costs less per month than people expect.
How much does custom vs. stock kitchen cabinets cost in San Francisco?
Stock cabinets installed run $8,000-$14,000 in San Francisco, semi-custom runs $15,000-$28,000, and full custom runs $30,000-$60,000 or more, all depending on kitchen size and layout. Call (866) 320-2646 for an exact quote; estimates are free.
Can I put stock cabinets in an older San Francisco kitchen?
Yes, but expect visible filler strips and gaps wherever the wall run doesn’t land on the 3-inch module, which is most pre-1920 kitchens. Semi-custom absorbs that gap in most cases, and full custom closes it entirely. A free design consult will show you which tier your room actually needs.
Are KraftMaid cabinets worth it over IKEA for a San Francisco kitchen?
For most San Francisco kitchens, yes, mainly because the plywood box and 3-inch adjustments fit the room better and hold up longer near exterior walls. IKEA makes sense on a newer condo or a rental where speed matters more than exact fit.
How long does a cabinet installation take in San Francisco?
Stock and semi-custom installs usually finish in one to three days once the cabinets land, and custom adds 12 to 20 weeks of lead time before install starts. Call (866) 320-2646 and we’ll pin down your timeline.
Ready to Stop Measuring Filler Strips?
If you’d rather have it looked at, Groundwork Construction Co. of San Francisco offers a no-pressure assessment in San Francisco. We’ll measure your walls, check the corners, and tell you straight which tier makes sense. Live person, 24/7. Call (866) 320-2646.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco, CA.