Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterStanding Seam Metal Roof in San Francisco, CA
A standing seam metal roof in San Francisco typically costs between $19,000 and $48,000 for a full residential installation, depending on roof size, pitch, and panel gauge. It’s the roofing type that best fits this city’s particular weather: wind-driven rain off the Pacific, salt air in the Sunset and Richmond, and a marine layer that keeps roofs damp for months without ever really soaking them. Standing seam panels lock together with raised seams that stand above the water plane, so water sheds fast and never sits against a fastener. That single design fact is why metal roofs hold up here where asphalt shingles start curling after a decade.
We install standing seam through our Roofing division, and it’s one of the more technical installs we take on. If you’re weighing it against shingles or a flat membrane, call (866) 320-2646 and a live person will pick up. Not a call center reading a script. A real person, 24/7.
We serve homeowners across the whole San Francisco service area, from Bernal Heights bungalows to Noe Valley Victorians to the larger homes up in St. Francis Wood. Every job comes with our 730-Day Done Right Promise: if the work isn’t right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing.
Why standing seam, specifically
Standing seam is different from other metal roofs. The panels are formed from one continuous piece of steel or aluminum, with a raised seam every 12 to 16 inches. There are no exposed fasteners on the field of the panel. On a screw-down metal roof, every screw is a potential leak point as the washers age. On standing seam, the fastener is hidden under a clip that lets the panel expand and contract with heat. That movement matters in San Francisco, where a roof on a south-facing slope in the Mission can swing 40 degrees between a foggy morning and an afternoon sun break.
Panels are usually 24-gauge steel with a Kynar 500 finish, or sometimes aluminum for homes close to the ocean where salt corrosion is a bigger concern. We don’t cut corners on gauge. A 26-gauge panel looks fine on day one and starts to oil-can and dimple after a few seasons of wind. The panels we install are spec’d for the wind loads and salt exposure of the specific address, not a one-size national standard.
When You Need Standing Seam Metal Roof
Most homeowners call us about metal roofing for one of these reasons. If any of them sound familiar, it’s worth getting a look.
- Your asphalt roof is nearing the end of its life and you don’t want to do this again in 20 years. A well-installed standing seam roof carries a 40 to 50 year service life. If you’re replacing a roof in your 40s, this is likely the last roof you’ll put on the house. Shingles will need another replacement inside most people’s ownership window; metal usually won’t.
- You’re on a hillside or exposed corner lot with wind-driven rain. Homes on the ridge lines in Diamond Heights, Twin Peaks, and the upper streets of Noe Valley take wind that pushes water sideways and up under shingle courses. Standing seam sheds that water off the raised seams instead of letting it wick under the laps.
- You’re within a mile or two of the ocean and asphalt is failing early. In the Outer Sunset and the Richmond, salt air and constant damp accelerate shingle deterioration. We regularly see 12-year-old shingle roofs in the Avenues that look like 25-year-old roofs inland. Metal doesn’t absorb moisture, so the marine layer doesn’t degrade it the same way.
- You’re dealing with tree debris and moss. Shingle roofs in Glen Park, Forest Hill, and the neighborhoods backed up to Mount Davidson collect needles and leaves that trap moisture and grow moss. Standing seam has a smooth surface; debris slides off or blows off instead of rotting into the mat.
- You want solar on the roof and don’t want to re-roof around it later. A metal roof lets us install standing-seam-mounted solar clamps that grip the seam without penetrating the panel. No drilled holes, no roof penetrations, no leaks around the solar mounts. If you’re planning solar in the next few years, doing the roof once in metal is often the smarter sequence.
- You’re heading into a major remodel and want the roof done right the first time. If you’re already tearing into the house, coordinating the roof with the rest of the build keeps the warranty on one contractor instead of split between two. Our team handles the roof in step with the project so nothing gets sequenced wrong.
- Fire zone concerns. Standing seam metal is a Class A fire-rated assembly. For homes in the wildland-interface edges of the city, that rating matters for insurance and for peace of mind.
Our Standing Seam Metal Roof Process
Every standing seam job follows the same disciplined sequence. We don’t skip steps because a crew is behind on another job, and we don’t sub out the metal work to a third party.
- On-site assessment and measurement. We walk the roof, measure the actual slope and panel runs, check the decking for soft spots, and look at the existing underlayment and flashing details. A standing seam roof is only as good as what’s under it, so if the deck needs repair we tell you before pricing, not after demo. Measurements get taken with a laser and cross-checked against the panel runs so the panel order is right the first time.
- Written upfront estimate and panel selection. You get a written price with line items: panel material, gauge, finish, underlayment, flashing, tear-off, disposal. No vague “allowance” lines. The number you see is the number you pay. We also walk through the finish colors and profiles so you’re choosing based on how it’ll look on your specific house, not a color chip in a fluorescent-lit showroom.
- Tear-off and deck repair. Old roofing comes off, the decking gets inspected and any rot or delamination gets replaced. We don’t panel over bad decking. If the decking needs replacement, we show you the photos before we do the work.
- Underlayment and flashing. High-temp synthetic underlayment goes down over the deck. We spend real time on the flashing details: valleys, chimneys, skylights, sidewalls, and the transition to flat roof sections. Most roof leaks we see on metal roofs come down to bad flashing, not bad panels. That’s the step where experience matters, and it’s the step most fly-by-night crews rush.
- Panel install and seam crimping. Panels are set in order, clipped, and aligned. Each seam gets crimped with a powered seamer, and every run is checked for alignment and clip engagement. We test the seamer on a scrap panel before running the actual roof, because a seamer that’s slightly out of adjustment can crease a panel edge and turn a $4,000 panel into scrap.
- Final walkthrough and warranty handoff. We walk the finished roof with you, show you the details, and hand over the 730-Day Done Right Promise in writing along with the manufacturer’s panel and finish warranty. If anything’s off, we come back. That’s the whole point of the promise.
Our technicians have up to 12 years of experience, and every one is background-checked and arrives in uniform. We don’t send a crew that showed up at the curb in an unmarked pickup. It matters when your roof is four stories up and the person on it is a stranger to you.
Standing Seam Metal Roof Pricing in San Francisco
Standing seam metal roofing in San Francisco runs about $19,000 to $48,000 for a typical residential roof, and it’s the higher end of residential roofing material costs. The honest reason is material price plus the labor it takes to install panel runs correctly on the complex, multi-pitch roofs common in this city’s older housing stock. Here’s how it shakes out:
| Cost Factor | Typical Range |
|---|---|
| Panel material (24-gauge steel, Kynar finish) | $12 – $20 per sq ft installed |
| Panel material (aluminum, for salt-exposed areas) | $18 – $28 per sq ft installed |
| Tear-off and disposal of existing roof | $2,500 – $6,500 |
| Deck repair (if needed, per square) | $400 – $900 |
| Flashing and detail work on complex roofs | $1,500 – $5,000 |
| Flat-to-metal roof transitions (common on SF Victorians) | $1,200 – $4,000 |
| Skylight, chimney, or solar mount flashing | $300 – $1,200 each |
| Full metal roof, 1,500 sq ft roof area, simple pitch | $19,000 – $28,000 |
| Full metal roof, 2,200 sq ft roof area, complex pitch | $34,000 – $48,000 |
What moves the price up or down most: roof area (obvious), roof complexity (the number of hips, valleys, and dormers; San Francisco Victorian roofs are notoriously busy), panel gauge, and whether you’re in a salt-exposed zone that requires aluminum panels. If your roof has a large flat section that needs a membrane in addition to the metal, that’s a separate line. If you’re adding solar, we can coordinate the mount system into the metal install so it’s done clean.
We also offer 0% financing for 18 months and $1,000 off projects over $10,000. Those two together take a lot of the sting out of the higher upfront cost of metal, and it lets you spread the spend without paying interest for a year and a half. Call (866) 320-2646 for a free estimate and design consult. No-hassle upfront pricing, no surprises.
Is it cheaper to repair or replace?
For a standing seam roof, repair almost always beats replacement unless the panel itself is damaged. A single dented or punctured panel can usually be replaced in a few hours without touching the rest of the roof. But if your question is really “repair my 20-year-old shingle roof or replace it with metal,” the math changes. A shingle roof that’s failing gets you another 15 to 20 years at best, and often less in a salt-exposed neighborhood. A metal roof gets you 40 to 50. Over that window, the per-year cost of metal is often lower. We’ll show you both numbers and let you decide. Call us for the comparison.
FAQs – Standing Seam Metal Roof
How much does a standing seam metal roof cost in San Francisco?
Most San Francisco homes land between $19,000 and $48,000 for a full standing seam metal roof, depending on square footage, roof complexity, panel gauge, and whether the panels need to be aluminum for salt exposure. A smaller, simpler roof on a bungalow in the Outer Sunset will be at the low end; a larger, complex-pitched Victorian in Noe Valley will be toward the high end. Call (866) 320-2646 for an exact number. Estimates are free and there’s no pressure to book.
Is a metal roof too loud in the rain?
No. When a metal roof is installed over solid decking with underlayment (which is how we install every roof), it’s actually quieter than most people expect, quieter than a bare shingle roof in some cases. The old “drumming metal roof” reputation comes from barns and sheds with open framing. A properly installed residential metal roof has deck, underlayment, and clips under every panel, which deadens sound. The rain noise is a non-issue for a San Francisco home that gets fog and mist more than downpours anyway.
Does a standing seam metal roof hold up to San Francisco weather?
Yes, and this is one of the better climates for it. Standing seam sheds water off the raised seams, doesn’t absorb moisture, and doesn’t corrode in the marine layer the way thin-gauge panel roofs do. The one issue to plan for is salt exposure near the ocean, which is why we spec aluminum panels in the Outer Sunset, Richmond, and anywhere within roughly a mile or two of the beach. A 24-gauge steel panel is fine inland; aluminum is the safer choice close to the salt. Call for a site-specific recommendation.
Can you come out today for a metal roof estimate?
We can usually get a same-week estimate scheduled, and for active leaks we treat the call as urgent. Call (866) 320-2646 and a live person answers any hour of the day. You’ll get a real time window, not a “someone will reach out.” If you’re actively leaking, we’ll prioritize the visit and get a temporary protection in place if needed before the full estimate.
Will a metal roof raise my homeowner’s insurance?
Usually the opposite. Standing seam metal is a Class A fire-rated assembly and is rated for high wind uplift, and many carriers discount premiums for it. We’ll document the install and the panel specs for you so you have the paperwork your insurer may ask for. If you want the exact rated assembly specs ahead of a call, we can send them. Call (866) 320-2646 and we’ll walk through what you need.
Do metal panels need to be installed over the old roof or can they go over shingles?
We tear off the old roof. We don’t install metal over the top of an existing shingle roof. The reason is deck inspection: you can’t check for rot, soft decking, or hidden leaks if you’re paneling over the old roof. And a metal roof over an un-inspected deck voids most panel warranties. The tear-off is a line item on your estimate, and it’s not negotiable on our jobs. We’d rather lose a bid than install a metal roof over unknown deck.
How does standing seam compare to James Hardie, KraftMaid, and other materials we might be considering?
Different product categories. James Hardie makes fiber cement siding, which is a wall product; KraftMaid makes kitchen cabinetry; Cambria makes quartz countertops. Those get used in other parts of the home, not on the roof. For a metal roof, we spec panels from established steel suppliers and finish them with Kynar 500, which is the industry standard coating for color retention and weather resistance. If you’re doing a whole-home exterior project, we can coordinate the roof with the other trades so the color and detailing line up. Call us and we’ll talk through sequencing.
How long does a standing seam metal roof take to install?
Most residential standing seam roofs take two to four days of active installation for the panel work, plus one to two days for tear-off and deck prep. Complex roofs with multiple pitches, dormers, and flat roof transitions can take longer. We’ll give you a real time estimate in writing before we start, and we don’t disappear mid-job to chase another bid. Call for a scheduling window.
If you’ve been putting off the roof decision because the bids you’ve gotten so far are vague or all over the map, that’s the conversation we’re built for. We do upfront pricing with a written estimate, and we back the work with the 730-Day Done Right Promise. If it’s not done right, we make it right. That’s the only thing we promise, and it’s the thing that matters most when you’re spending five figures on a roof.
Our team handles standing seam alongside every other roofing scope on the same job sheet, so if the metal install needs to coordinate with a flat roof membrane, a skylight, or a solar mount, it’s one point of contact. Built to last, backed in writing. Call (866) 320-2646 for a free estimate and design consult, and we’ll get a real number in front of you this week.
Written by the team at Groundwork Construction Co. of San Francisco, serving San Francisco.