Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Larkspur, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in Larkspur typically runs $3,500 to $10,000 and takes about 5 to 10 working days from demo to final caulk. The job means pulling the tub, reworking the drain and valve to shower spec, rebuilding the waterproofing, setting a new pan and walls, and resetting tile or panels. Most Larkspur tub-to-shower conversions land in the middle of that range. Call (866) 320-2646 for a free on-site estimate and a written, line-item number.
How a Tub-to-Shower Conversion Actually Runs, Stage by Stage
Here’s the real sequence. It’s the same on a Magnolia Avenue bungalow as it is on a hillside home, but the details change with what’s behind the wall.
Stage 1: Site protection and demo (day 1)
We mask the hallway and any adjacent rooms, shut off the water, and pull the tub, surround, and old valve trim. Plaster and drywall come out down to studs around the wet wall. On older Larkspur homes, expect a few surprises: galvanized supply lines, a cast-iron drain with a leaded joint, or lath-and-plaster walls that come off slower than drywall. This stage is one day on a straightforward job, up to two if we find water damage or need to open the wall further.
Stage 2: Rough-in and inspection (days 2 to 3)
This is where the conversion really happens. The existing tub drain sits about 6 to 8 inches above the floor, and a shower drain needs to be closer to grade while the valve body has to move up to roughly 40 inches. We set a new shower valve, rework the drain and venting to code, and frame any niche or bench. A licensed plumber and electrician handle their parts, and the rough-in gets inspected before anything closes up. That inspection timing is the one thing we don’t control – plan for it in the schedule.
Stage 3: Waterproofing and setting the pan (days 4 to 5)
We install a sloped mortar bed or a bonded waterproofing membrane, then a waterproof board on the walls, then flood-test the pan. This is the stage most homeowners don’t see and the one that determines whether the job lasts 15 years or 5. You’ll decide at this point whether you want a curb or a curbless entry – curve decisions get made here, not later.
Stage 4: Tile, panels, and fixtures (days 6 to 8)
Tile gets set, grouted, and sealed, or the panel system goes up. Then the shower head, valve trim, glass, and niche shelves. This is your last chance to change a finish – once tile sets, changing your mind means re-demo.
Stage 5: Final walk and punch list (day 9 to 10)
We silicone the seams, test for leaks, clean up, and walk the job with you. You approve each item before we’re done. Any punch list items get handled before final payment.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of your decisions happen in week one, so it pays to walk in with a rough preference. Here’s the honest trade-off on each:
- Acrylic or fiberglass shower panels: the fastest and least expensive route, usually $2,000 to $4,000 in materials. Non-porous, easy to clean, and holds up well in a rental or secondary bath. Trade-off: fewer size and color options, and composite panels can flex in a hot shower over years.
- Ceramic or porcelain tile: the standard choice for a primary bath. Runs $1,500 to $5,000 in materials depending on grade. Porcelain is denser and holds up better in Marin’s damp winters; ceramic is easier to cut and cheaper. Trade-off: grout needs sealing and quiet maintenance.
- Natural stone (marble or travertine): beautiful, but it demands more sealing and maintenance in a wet environment. Expect $4,000 to $8,000 in materials. Suits homeowners who don’t mind the upkeep.
- Shower pan style: a pre-sloped acrylic pan is the value play. A tiled pan gives you flexibility on dimensions – helpful in older Larkspur homes where the framing isn’t perfectly square.
- Glass and enclosure: framed doors cost less, frameless glass looks cleaner and opens up a small bath. A frameless enclosure adds $800 to $1,800 and needs firmer blocking at installation.
- Fixtures: Kohler is our go-to for valves and trim because the cartridges hold up and the parts are available. Upgrading to a thermostatic valve adds a couple hundred dollars but gives you temperature control for a family bath.
What Tub-to-Shower Conversion Costs in Larkspur, CA
The number for a tub-to-shower conversion here starts at $3,500 and tops out around $10,000. That’s the range, and it’s real – not a teaser. Here’s what pushes a job toward one end or the other:
- Moving the drain and valve: the single biggest swing. If the tub drain converts cleanly, you stay near the low end. If we need to relocate the drain, re-vent it, or move the valve to a new wall, add $500 to $2,000.
- Existing condition: a solid 1990s construction is straightforward. A 1920s downtown Larkspur home with galvanized pipe, a cast-iron drain, and lath-and-plaster walls adds $1,000 to $2,500 in rework.
- Size and configuration: a standard 5-foot alcove is the baseline. A wider shower or a curbless entry adds framing, waterproofing, and labor.
- Material grade: panels versus tile versus stone moves the number by thousands, as you saw above.
- Permit scope: the plumbing and electrical rough-in get inspected, and permit fees in Larkspur for a bath job typically run a few hundred dollars. That’s not padding – it’s a line item.
Every written estimate we hand you is a line-item quote: demo, rough-in, waterproofing, tile, glass, fixtures, permit, cleanup. What’s typically not included is a surprise: if we open the wall and find rot, mold, or a failed drain, that’s a change order and you approve it before we proceed. No-hassle upfront pricing means the number you see is the number you pay – unless you add scope.
See the difference
Before
After
Before
After
Before
AfterWhat Larkspur Homes Specifically Do to This Job
Larkspur isn’t a suburb where new subdivisions make the job easy. The town is largely built out, and most of the work is remodel on old downtown Victorians and bungalows along Magnolia Avenue, mid-century hillside homes, and a scattering of infill. That housing stock changes the job in specific ways. Older baths often hide galvanized supply lines, undersized venting, and lath walls that raise labor. Hillside and canyon homes sometimes bring drainage and framing quirks into the bath – a sloped floor that wants to throw the shower pan out of level, or a wall cavity that’s tight on the wet wall. And because Larkspur’s Design Review process scrutinizes exterior changes far more closely than in neighboring Corte Madera or San Anselmo, anything touching an exterior wall or window gets reviewed harder. Marin’s wet winters squeeze the schedule, so we plan the waterproofing stage around the rain. Wildfire exposure also means fire-hardening details sometimes ride alongside a bath project – homeowners who are thinking about defensible-space improvements often pair this with Metal Roofing in Larkspur or Tile Roofing in Larkspur. If your enclosure is part of a wider plan, our Bathroom Remodeling in Larkspur page covers the full scope.
Tub-to-Shower Conversion FAQs for Larkspur
Plan on 5 to 10 working days from demo to final walk, with the inspection stage being the wildcard. Most Larkspur jobs land around 7 days. If we find hidden damage or the rough-in needs rework, add 2 to 4 days. Call (866) 320-2646 for a schedule tailored to your bathroom.
Yes, if the plumbing or electrical rough-in is changing – and a conversion almost always changes the drain and valve. That means a plumbing permit and an inspection before the walls close. We pull the permits and coordinate the inspection so you’re not chasing the building department. Call (866) 320-2646 to talk through your specific job.
Often, yes – if the shower drain can tie into the existing tub drain with a modest relocation. In many alcove baths, the drain and valve work stays within the footprint. When it can’t, you’ll hear it in the estimate, not after demo. Call (866) 320-2646 and we’ll look at your layout.
The range is $3,500 to $10,000, with most Larkspur jobs landing mid-range. Drain relocation, older plumbing, and material grade are the biggest variables. Call (866) 320-2646 for an exact quote – estimates are free.
Every tub-to-shower conversion we do is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That runs two full years on the workmanship, which is longer than most contractors in the trade offer. Our technicians have up to 12 years of experience. Call (866) 320-2646 to schedule your free estimate.
Serving Larkspur, CA – Our Local Coverage Area
We serve Larkspur and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Get a Free Tub-to-Shower Conversion Estimate in Larkspur
Call (866) 320-2646 to schedule a free on-site estimate for your tub-to-shower conversion in Larkspur. A live person answers, day or night, and we’ll set a time that works. We walk your bath, measure the alcove, talk through panel versus tile, and explain exactly what the permit and inspection will involve. You’ll get a written line-item estimate – no surprises and no change orders without your approval. We serve Larkspur and the surrounding Marin towns. Every job is backed by our 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co.