Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Petaluma: What It Costs and How Long It Takes
A tub-to-shower conversion in Petaluma typically runs $3,500 – $10,000 and takes 5 to 10 working days once the permit is in hand. The job means pulling the old tub, reworking the drain and valve as needed, waterproofing the wet area, and setting a new shower base, walls and glass. Most Petaluma conversions land near $6,500 for a standard alcove with a tiled pan and a framed glass door. Call (866) 320-2646 for a free on-site estimate.
How the work actually unfolds, day by day
Conversions go sideways when a contractor skips stages. Here’s the real sequence we run on a Petaluma tub-to-shower conversion, and where you make decisions along the way.
- Days 1 – 2: Demo and inspection. We pull the tub, the surround and any furring, then open the valve wall to see what’s behind it. That’s when we learn whether the drain line is cast iron or ABS, whether the old valve is a two-handle relic, and whether there’s water damage in the subfloor. You decide whether to replace the valve now or keep what’s there.
- Day 2: Rough-in changes. If you want the drain centered, the valve moved, or a niche added, this is when the framing and plumbing happen. Moving the drain off its existing line adds a day and a plumbing charge. After rough-in we call for rough inspection if your job requires one.
- Days 3 – 4: Waterproofing. Cement board or a foam shower system goes up, then a liquid or sheet membrane over the pan and walls. This stage gets inspected before a single tile is set. Skip it and you’re redoing the shower in three years.
- Days 5 – 8: Tile and setting. Wall tile, pan tile, grout, sealant. You’ll have already chosen tile and grout by this point. Larger format tile moves faster; small mosaic on the pan takes longer to set.
- Days 9 – 10: Glass, trim and final. Shower door, trim kit, caulk, final inspection, cleanup. You’ll walk the job with us and get the warranty in writing.
The timeline holds if materials are on site before demo starts. Ordering tile after demo is the number one reason a two-week job stretches to five. We lock the material schedule before we swing a hammer.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices that define your conversion
Almost every decision here trades money against longevity or maintenance. Here’s what you’re actually picking between.
- Acrylic or fiberglass pan vs. tiled pan. A prefab acrylic pan costs less and installs faster, and it’s the easiest to clean. A tiled pan with a linear drain looks better and lets you set the tile to the drain, but it costs more and depends entirely on correct waterproofing. Choose the tiled pan if you want a curbless entry or a specific look; choose acrylic if you want it done and low-maintenance.
- Tile vs. solid-surface walls. Porcelain or ceramic tile runs the gamut from budget to high-end and lasts. A cultured marble or solid-surface wall panel installs in a day with almost no grout lines to scrub, but it shows hard-water spots and can’t be patched invisibly.
- Glass enclosure. A framed door is the value option. Frameless 3/8-inch glass is the look most Petaluma homeowners ask for, and it costs more and needs a perfectly square opening. Fixed glass panels with a swing door suit larger showers.
- Valve and fixture grade. A standard pressure-balance valve is fine. A thermostatic valve with a separate volume control costs more and holds temperature better on cold mornings. You’re choosing brand finishes here too; Kohler is a common pick because trim is available in the finish you want years later.
- Niche and bench. A recessed niche costs little if built during rough-in and a lot if added later. A bench is worth the money in a shower used by anyone older or unsteady on their feet.
What Tub-to-Shower Conversion costs in Petaluma, CA
Expect $3,500 – $10,000 for a tub-to-shower conversion in Petaluma. A straightforward alcove swap with a prefab pan and a basic tile surround sits near the bottom; a tiled pan, frameless glass, new valve and niche with premium tile sits near the top.
Here’s what moves the number:
- Size and footprint. A standard 60-inch alcove is the cheapest to convert because everything is made for it. A wider shower or a curbless entry requires structural work and more tile.
- Existing condition. Rot in the subfloor, a corroded drain line, or a valve that has to be replaced behind the wall adds $400 – $1,500 depending on what we find after demo.
- Moving plumbing or electrical. Relocating the drain or valve, adding a recessed light, or wiring a vent fan means a plumbing or electrical sub and usually a permit amendment.
- Material grade. Budget porcelain vs. large-format stone-look tile can swing the material cost by a couple thousand dollars. Frameless vs. framed glass is a $600 – $1,200 difference on its own.
- Permit scope. A like-for-like swap may not need a plumbing permit; relocating the drain or changing the valve usually does. We pull it and pass inspection, and that cost is in the written estimate.
Our estimate is line-item and upfront: tile, setting materials, glass, fixtures, labor, permit and haul-away are each shown. The number you see is the number you pay. What isn’t included is what nobody can see until demo, like subfloor rot or a failed drain line; we stop and price those before doing the work. Projects over $10,000 get $1,000 off, and 0% financing for 18 months is available.
See the difference
Before
After
Before
After
Before
AfterWhat Petaluma homes specifically do to this job
Petaluma’s housing stock splits hard, and it changes how a conversion goes. In the Victorian and early-1900s wood-frame homes downtown and on the west side, we routinely find cast-iron drains, original galvanized supply lines and subfloors that have taken on water for decades. Those homes often sit on raised foundations over flood-prone ground near the Petaluma River, so a shower that leaks doesn’t just stain a ceiling: it saturates framing that’s already been through atmospheric-river winters. That’s a case for a proper pan membrane and a pre-slope, not a shortcut.
The east side, the 1970s – 2000s stucco tract homes off McDowell and East Washington, mostly needs a valve upgrade and a drain that’s already ABS, and the work moves faster. Either way, plan around Petaluma’s dry-season construction window if the job touches framing or exterior walls: wet winters here push water intrusion repairs into spring. And if your home is in the historic downtown core, expect city review on anything visible from the street before exterior work begins; interior conversions usually skip that, but we confirm before we schedule. We cover the whole city, from the 94952 river corridor to the east-side subdivisions, and everywhere in between through our Petaluma service area. For a broader scope that combines this with vanity and flooring work, see Bathroom Remodeling in Petaluma, and for the full range of work we do, our Bathroom Remodeling service. Homeowners often pair a conversion with a roof project, and we handle Metal Roofing in Petaluma and Tile Roofing in Petaluma as well.
Serving Petaluma, CA – Our Local Coverage Area
We serve Petaluma and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Tub-to-Shower Conversion in Petaluma
Most conversions take 5 to 10 working days from demo to final walkthrough, plus permit turnaround if your job needs one. A simple alcove with a prefab pan and basic tile lands near five days; a fully tiled pan, frameless glass and a valve move runs closer to ten. Material lead times are the wildcard, so we order tile and glass before demo starts. Call (866) 320-2646 for a schedule on your specific shower.
You need a permit when the job moves the drain, changes the valve, or adds electrical, and often not for a straight like-for-like swap. The safe answer is to check with the city before demo, because unpermitted plumbing surfaces at resale. We pull the permit when one is required and pass the rough and final inspections, and that cost is shown in your written estimate. Call (866) 320-2646 and we’ll tell you which category your job falls into.
Yes, and most conversions don’t need either. If the existing drain and valve sit where you want them, the job is a pull-and-replace with new waterproofing and finishes. Moving the drain to center it, relocating the valve, or going curbless adds framing and plumbing work. We confirm what’s feasible at the estimate visit and price the alternatives so you can decide. Call (866) 320-2646 to set that visit up.
The range is $3,500 – $10,000 for a typical Petaluma conversion. A budget alcove with a prefab pan and framed glass sits near $3,500; a tiled pan, frameless glass, new valve, niche and premium tile pushes toward $10,000. Hidden conditions like subfloor rot or a failed drain line add cost once we open the wall. Call (866) 320-2646 for a free on-site estimate with line-item pricing.
Every conversion we do is covered by the 730-Day Done Right Promise: if it’s not done right, we make it right, for two full years. That covers our labor and waterproofing on the shower itself, alongside the manufacturer warranties on tile, glass and fixtures. Our technicians have up to 12 years of experience and are background-checked and uniformed. Call (866) 320-2646 to schedule your free estimate.
Get your Petaluma conversion priced
Call (866) 320-2646 to set up a free on-site estimate for your tub-to-shower conversion. We look at the existing shower, check the drain and valve, and hand you a written, line-item price with the permit and material costs spelled out. Calls are answered by a live person, 24/7. No pressure, no obligation. You’ll know the number before anybody touches a tile.
Written by the team at Groundwork Construction Co.