Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
What a wood fence in San Francisco actually costs and how long it takes
Wood fence installation in San Francisco runs about $4,130 to $10,620 for most residential jobs, and a typical run of 40 to 60 linear feet is finished in two to four working days once materials land on site. The wide spread comes down to access, height, and how the posts get anchored into what’s often a shared lot line on a hill. Call (866) 320-2646 and we’ll walk your property, measure the run, and give you a written line-item estimate. We connect San Francisco homeowners with independent local crews who build this work every week, and every job is covered by our 730-Day Done Right Promise.
How we build a wood fence here: day by day, decision by decision
Fence work in a dense city is mostly a logistics job with carpentry at the end. Here’s what actually happens, and where you’ll need to make a call.
Stage 1: Site walk and survey (60 to 90 minutes)
We measure the full run, confirm where the property line sits relative to the existing fence, and flag anything buried – irrigation lines, low-voltage lighting, old concrete footings from a previous fence. On steep lots we note the grade change across the run, because a fence that steps with the slope is built differently than one that racks in a straight line. You decide at this stage whether you want the fence to sit exactly on the line or inset a few inches for easier maintenance access.
Stage 2: Demo and haul-off (half a day to a full day)
Old fence panels come down, posts get pulled or cut at grade, and debris goes into a dumpster we place as close to the work as the street allows. In San Francisco this is where parking and alley access matter most – a narrow shared driveway on a hill means hand-carrying panels or staging from the street with a permit. You’ll want to confirm whether you’re keeping any section of the existing fence, since salvaged panels can offset cost.
Stage 3: Post setting and curing (one day on site, then a cure window)
Post holes get dug, depth checked against the run height, and posts set in concrete. We don’t hang panels the same day. The concrete needs to cure before the fence carries a wind load. This is the single biggest reason a fence job isn’t a one-day project, and it’s the stage most cheap bids skip. You decide the post spacing here, typically 6 to 8 feet on center depending on panel design.
Stage 4: Framing, panels, and gates (one to two days)
Rails go on, panels get hung, and the gate gets fit and hung with hardware rated for exterior use. Gate fit is where a fence earns or loses its reputation – a gate that drags or sags within a season wasn’t hung right. You’ll pick your gate swing direction and latch style at this point if it wasn’t settled in the estimate.
Stage 5: Finish and final walk (half a day)
We apply the finish coat if it’s in scope, touch up cut ends, and walk the whole run with you. Every post gets a shake test, every gate gets opened and closed, and we note anything that needs a return visit. Nothing gets signed off until you’ve walked it. Then the 730-Day Done Right Promise starts, backed in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The wood fence options you’ll actually choose between
Most of the cost swing on a San Francisco wood fence comes from these choices, not from labor. Here’s the honest version of each.
- Cedar vs. pressure-treated pine: Cedar costs more per linear foot but holds up better against the marine fog and damp that eat untreated wood on the west side. Pressure-treated pine is the budget pick and needs a re-stain every couple of years in this climate. For a fence you plan to keep 15-plus years, cedar usually wins.
- Dog-ear, flat-top, or custom cap: Standard dog-ear pickets are the cheapest and most common. A flat-top or capped design looks more finished and adds cost. Capped fences shed water off the top rail, which matters more here than in a dry climate.
- Height: 6 feet is the residential default. Going to 7 or 8 feet pushes material and hardware cost up and can run into height limits on some lots, so it gets checked early.
- Board-on-board vs. butted pickets: Board-on-board (overlapping) gives more privacy and better wind resistance, at a higher material cost. Butted pickets are cheaper but show gaps as the wood dries.
- Hardware and fasteners: This is where San Francisco-specific choices matter. Standard galvanized nails can corrode fast in the salt air and fog belt. Stainless or hot-dipped galvanized fasteners cost more up front and last far longer.
For the wider project – gates, matching fencing around a garage, or a bigger lot-line rebuild – see our Fence Installation service.
What a wood fence costs in San Francisco, CA
Plan on $4,130 to $10,620 for a residential wood fence in San Francisco. That range covers a typical lot-line run with gates and finish. Five things push a job toward the low or high end:
- Linear footage: The single biggest driver. A short 30-foot run sits near the bottom of the range; a full perimeter with two gates climbs toward the top.
- Access and staging: Hillside lots, narrow shared driveways, and street-parking permits add labor. A fence that has to be hand-carried up a slope costs more than one backed up to an alley.
- Old fence removal: Demoing and hauling off an existing fence – including cutting out old concrete footings – is real labor. Skipping it saves money but only if you remove it yourself.
- Material grade: Cedar over pressure-treated pine, board-on-board over butted pickets, and stainless hardware over standard galvanized all move the number.
- Grade change: A fence that steps down a steep lot requires more posts, more panels, and more cuts than a flat run.
A written estimate from us is line-item, so you see material, labor, removal, and finish as separate numbers with no surprises. Finishing or staining is included when it’s in scope; things like a new gate operator or landscape repair along the line are quoted separately.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco homes specifically do to this job
San Francisco’s housing stock shapes every wood fence we build here. The city is dense with 1880s-1920s Victorian and Edwardian wood-frame row houses on brick foundations, and a lot of those fences sit on shared lot lines where the grade drops sharply between neighbors. On the west side, the fog belt and Pacific salt air accelerate rot and paint failure on exposed timber, which is why we spec stainless and hot-dipped galvanized hardware even on short runs – standard fasteners can corrode within a fraction of their normal lifespan out there.
Permitting is its own reality. San Francisco planning and building review is unlike anywhere else in the Bay Area, and fences on or near a lot line, or above a certain height, can require a survey and neighbor sign-off before work starts. On hillside properties in areas like Noe Valley or the steep blocks near Twin Peaks, post footings have to account for slope and drainage. Pre-1906 Gold Rush-era and post-1906 rebuild stock means many fences we replace were never on a proper footing. We check that before we quote. Coverage across the city’s neighborhoods is on our San Francisco page.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked about wood fences in San Francisco
Most residential wood fences take two to four working days on site, plus a concrete cure window before panels go up. Hillside access, permit review, or a large perimeter can extend that to a week or more. Call (866) 320-2646 and we’ll give you a realistic schedule once we’ve seen the run.
It depends on height and placement. Fences above the standard residential height, or those on certain lot lines, can require a permit and a survey. We check your specific lot before quoting so there’s no surprise mid-job. Call (866) 320-2646 to talk through your property.
Usually, yes. Post placement is planned around existing utilities, and if we hit a buried irrigation line or low-voltage lighting run, we adjust the post layout. If a gas or electrical line sits right where a post must go, that gets flagged and handled carefully by the appropriate trade. Estimates are free – call (866) 320-2646.
Residential wood fences in San Francisco typically run $4,130 to $10,620, driven by linear footage, access, removal, and material grade. Call (866) 320-2646 for an exact written quote.
Every wood fence we build is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space. Call (866) 320-2646 to get your estimate started.
If you’re also reworking the approach to the fence line, homeowners often pair this with Paver Driveways in San Francisco or with Concrete Driveways & Concrete Work in San Francisco for a cleaner transition from street to yard. For a full property line rebuild that goes beyond a single run, see our Fence Installation in San Francisco page for the wider scope.
Get a free wood fence estimate in San Francisco
Call (866) 320-2646 to schedule a free on-site estimate and design consult for your wood fence in San Francisco. A live person answers around the clock, and we’ll walk the run, check the lot line and grade, and hand you a written line-item quote – no surprises. We’ll talk through material choices, timeline, and permit needs so you know exactly what you’re getting before you commit.
Written by the team at Groundwork Construction Co.