Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in Daly City, CA: What It Costs and How It Holds Up
Aluminum fence installation in Daly City typically runs $4,000 – $10,000 for a standard residential run, and most jobs take two to four days once the layout is marked and the holes are dug. The number you land on depends on linear footage, height, panel style, and how much prep your hillside lot needs before the first post goes in. Call (866) 320-2646 for a free on-site estimate and a written line-item quote before anything starts.
How Our Aluminum Fence Process Works, Start to Finish
Aluminum fence rewards planning more than any other fence material we install. The panels are light and go up fast, but a post set out of plumb on a Daly City slope will never look right, and no amount of adjusting fixes it later. Here’s how a typical job moves.
Stage 1: Site visit and layout (day 1, about 60 – 90 minutes)
We walk the property line with you, confirm the exact run and gate locations, and check what’s under the ground before we commit to anything. On steep lots, we note where the grade changes and where utilities are likely buried. You decide the fence height, gate swing, and whether you want a partial run or full enclosure at this stage. This is also when we flag any section that ties into a larger project you’re planning as part of Fence Installation in Daly City.
Stage 2: Utility marking and permits (days 1 – 5, handled in parallel)
We call for utility locating before any digging, which is non-negotiable when posts are going in near property lines and shared walls. If your run requires a permit, we pull it and schedule inspection. You don’t chase paperwork; we handle the submission and tell you when the inspection is set. Homeowners only need to be reachable if the inspector needs access.
Stage 3: Demolition and post setting (days 1 – 2 of on-site work)
If there’s an old fence, it comes out first, and that’s often where the surprises live. Rotted posts, broken concrete footings, and overgrown roots add time. We set aluminum posts in concrete footings, checked for plumb and depth, and give them the cure time the mix requires before hanging panels. This is the stage where slope work shows: on a graded run, post heights get stepped or racked to follow the ground.
Stage 4: Panels, gates, and hardware (day 3)
Panels go up, gates get hung and adjusted for swing and latch alignment, and we check every connection. You decide gate hardware here if you haven’t already: self-closing hinges, a keyed latch, or a simple thumb-latch. On a coastal Daly City lot, we also talk through hardware finish because the fog will test it faster than you’d expect.
Stage 5: Walkthrough and closeout (same day, 20 – 30 minutes)
We walk the full run with you, test every gate, and confirm nothing is loose. Any punch items get noted and handled. You get the workmanship paperwork, and the job is covered under our 730-Day Done Right Promise. If it’s not right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Aluminum Fence Options You’ll Choose Between
Aluminum isn’t one product. The choices below are the ones that actually change how your fence looks, how long it lasts in Daly City’s fog belt, and what you pay.
- Panel style and picket spacing: Standard 3-rail with 4-inch pickets reads clean and private-ish. Tight spacing (under 4 inches) costs more and closes sightlines, which matters on narrow lots with close neighbors. Ornamental styles with decorative tops cost the most.
- Height: 4-foot is common for boundary marking, 5-foot for privacy screening, 6-foot for security. Taller runs need more posts and footings, so the per-foot price climbs.
- Finish: Powder-coated aluminum in black, bronze, or white holds color well in coastal air. A factory finish resists the salt fog far better than a field-painted surface, and it’s the option we steer most Daly City homeowners toward.
- Hardware and fasteners: Stainless or coated fasteners are the difference between a fence that looks new in eight years and one with rust streaks. This is a small line item with outsized impact in salt air.
- Gate type: A walk gate costs less than a drive gate. A self-closing or keyed gate adds cost but solves security and safety concerns on a hillside property.
Aluminum runs lighter and holds finish better than wood in wet coastal air, and it’s the lower-maintenance choice compared with a chain link run that needs constant attention. It’s a good fit for homeowners who want the look without repainting every few years.
What Aluminum Fence Costs in Daly City, CA
Most aluminum fence projects in Daly City land in the $4,000 – $10,000 range. Here’s what pushes a job toward the low or high end.
- Linear footage: A 60-foot boundary run sits near the bottom; 150 feet with gates and corners climbs toward the top.
- Slope and grading: Racked or stepped panels on a steep lot take more labor and more posts than a flat run.
- Existing fence removal: Demo, concrete footing removal, and disposal add time and cost.
- Contractor access: Tight lots where neighbors’ walls are only feet away make material handling slower.
- Permit scope: A permit and inspection add to the total but protect you on resale and boundaries.
Our written estimate breaks out panels, posts, footings, gates, hardware, demo, permit fees, and labor line by line. Upfront pricing, no surprises: the number you see is the number you pay, and changes only happen if you approve them in writing. Typically the estimate covers materials and standard installation; unusual site work, retaining wall adjustments, or major excavation comes as a separate line so you see it before you commit.
See the difference
Before
After
Before
After
Before
AfterWhat Daly City Homes Specifically Do to This Job
Daly City’s dense rows of post-war stucco-over-wood-frame homes sit on steep, fog-soaked slopes, and that shapes every aluminum fence we install here. On the streets off Mission and around Westlake, property lines run across grade changes, neighbors’ walls are feet away, and old fences are often tied into redwood framing that’s quietly rotted from years of damp air. Materials come in through tight side yards, and posts sometimes land near buried utility runs in ways flat lots never see. We plan access before the first panel arrives. The 94015, 94016, 94017, and 94014 ZIP codes all share the same pattern: wind-driven rain and cool fog that attack exposed metal faster than inland sun does, so we spec coated finishes and stainless hardware as standard, not upgrades. When a fence project ties into drainage, a retaining wall, or a driveway, homeowners often pair this with Driveway Repair & Replacement in Daly City or Patios, Walkways & Pool Decks in Daly City so the site work happens once.
Serving Daly City, CA – Our Local Coverage Area
We serve Daly City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Aluminum Fence in Daly City
Most aluminum fence jobs take two to four days of on-site work, with permit review adding days before that. A simple 60-foot run on level ground is often done in two days; a sloped run with removal and a gate takes closer to four. Call (866) 320-2646 for a timeline based on your property.
It depends on height, location on the lot, and your property line conditions, and we confirm that during the site visit. Where a permit is required, we pull it and schedule the inspection. You don’t handle the paperwork.
Yes in most cases. Aluminum posts set in shallow concrete footings, so we avoid trenching deep near sewer lines or foundations. We still call for utility locating before digging, and on tight Daly City lots we plan post placement to stay clear of buried services.
Expect $4,000 – $10,000 for a standard residential run, driven by footage, height, gate count, and slope. Call (866) 320-2646 for an exact quote; estimates are free and come in writing.
Every job is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right for two years. That’s one of the longest workmanship guarantees in the residential space, and it applies to the installation, not just the material.
Get a Free Aluminum Fence Estimate in Daly City
If you’re pricing an aluminum fence in Daly City, the fastest path is a free on-site estimate. Call (866) 320-2646 and a live person answers, day or night. We’ll schedule a visit, measure the run, walk the grade, talk through panel styles and hardware, and hand you a written line-item quote with no surprises. See the wider scope on our fence installation service, or review everything we cover across Daly City.
Written by the team at Groundwork Construction Co.