Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Concrete Driveways & Concrete Work in San Bruno: What You’re Actually Getting Into
Concrete driveways and concrete work in San Bruno typically run $4,500 – $12,000 for a full pour, and a straightforward driveway is usually a three-to-five day job from demo to cure. Call (866) 320-2646 and we’ll walk your slope, measure the square footage, and hand you a written line-item quote on the spot. The number you see is the number you pay.
What makes concrete here different from inland is the fog. San Bruno sits in the marine layer, and that cool damp air does things to a pour that a Sunnyvale driveway never has to deal with. More on that below, because it’s the whole reason this page exists.
How We Pour Concrete in San Bruno, Stage by Stage
Concrete work fails or succeeds on prep, not on the pour itself. Here’s the real sequence, with the decisions you’ll make at each point.
Day 1: Demo and haul-off
We tear out the old slab, broken sections, or the grass and topsoil, then haul it away. A standard two-car driveway demo runs most of a day. This is where we find out what’s underneath – tree roots, old footings, a buried oil tank, or a failing subbase. If something structural turns up, we stop and tell you before the number changes. No surprise invoices mid-job.
Day 1 – 2: Grading and subbase
We excavate to depth, then lay and compact a crushed rock base, usually 4 to 6 inches depending on soil and load. This is the stage homeowners never see and the one that determines whether your driveway cracks in year three or holds for decades. Drainage slope gets set here too – water has to run away from the garage, not toward it. You’ll decide at this point whether you want a swale, a channel drain, or a simple slope. Channel drains add cost but solve a real problem on flat lots.
Day 2 – 3: Forms, rebar, and inspection
We set forms to the finished grade, install rebar or wire mesh, and – if your project requires a permit – call for inspection before any concrete goes down. Once it’s poured, nobody can verify what’s inside. That’s why we don’t skip it. You’ll confirm the layout and finish choice before this stage closes.
Day 3: The pour
Concrete arrives, gets placed, screeded, floated, and finished. A broom finish is standard for driveways and gives you grip when it’s wet – a real concern on a foggy San Bruno morning. Exposed aggregate and stamped finishes cost more and take longer but hold up well. Control joints get cut either same-day or the next morning, and those joints are not optional. They tell the slab where to crack instead of letting it choose.
Day 4 – 5: Cure and cleanup
Concrete reaches usable strength in about 48 to 72 hours for foot traffic, longer for vehicles – typically seven days before you park on it. We keep off it, pull forms, clean the site, and walk the finished work with you. Your written workmanship warranty starts here.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Concrete isn’t one product. Here’s what you’re picking from, and what each choice really costs you.
- Standard broom-finish concrete – the workhorse. Best grip, lowest cost, holds up in wet coastal weather. If your driveway is functional rather than decorative, this is the right call.
- Exposed aggregate – the top layer gets washed to reveal the stone underneath. Texture hides tire marks and small cracks, and it ages well. Costs more per square foot and takes extra finishing time.
- Stamped concrete – patterned to look like stone or brick. The most decorative option, and the most expensive. In San Bruno’s damp air, sealant needs reapplying every couple of years to keep the pattern crisp.
- Thickness – 4 inches is the standard for passenger cars. If you park a heavy truck, an RV, or you’re pouring where a loaded vehicle turns, go to 5 or 6 inches with heavier rebar. It’s a modest line-item cost that prevents real failure.
- Joint layout – where the control joints land is a design decision, not an afterthought. We lay them out so the pattern reads clean and the slab cracks where it’s supposed to.
- Drainage extras – channel drains, trench drains, or a simple French drain at the low corner. Add these if your lot is flat or the driveway slopes toward the house.
On materials, we work with established suppliers and hold the concrete to a proper mix design – not whatever’s cheapest that morning. When your project widens out to the wider hardscape, it becomes part of a full Driveway & Pavers in San Bruno scope, and you can read about our broader Driveway & Pavers work there.
What Concrete Driveways & Concrete Work Costs in San Bruno, CA
A full concrete driveway installation in San Bruno runs $4,500 – $12,000. A replacement of an existing driveway lands in the $5,000 – $14,000 range because demo and haul-off add cost. Here’s what moves the number:
| Line item | Typical San Bruno range |
|---|---|
| Concrete driveway installation | $4,500 – $12,000 |
| Driveway replacement (demo + new pour) | $5,000 – $14,000 |
| Driveway sealing (maintenance coat) | $250 – $700 |
The variables that push a job to the low vs high end:
- Square footage and access. A tight San Bruno lot where a wheelbarrow is the only way to reach the pour costs more than a wide-open lot a truck can back into.
- Existing condition. Old slab, tree roots, failing subbase – all add demo and excavation time.
- Finish grade. Broom is baseline; stamped or exposed aggregate pushes you toward the top of the range.
- Thickness and reinforcement. Going from 4 to 6 inches with heavier rebar is a real but worthwhile line item.
- Drainage work and permit scope. Drains, retaining edges, and any required inspection add to the total.
Every written estimate itemizes demo, base, rebar, concrete, finish, and cleanup so you can see exactly what you’re paying for. We don’t quote a lump sum and leave the details to chance. Call (866) 320-2646 for an exact quote – estimates are free, and financing is available at 0% for 18 months.
See the difference
Before
After
Before
After
Before
AfterWhat San Bruno Homes Specifically Do to This Job
San Bruno’s building stock and its history both show up in the concrete we pour. The Crestmoor neighborhood and the surrounding streets are dominated by post-WWII single-family homes from the 1940s and ’50s – and a large share were rebuilt or heavily retrofitted after the 2010 PG&E gas pipeline explosion. That event reshaped how this city permits and inspects work, and it’s why contractors here need to know the local ground rules before they dig.
Two practical things follow. First, any digging near the old Crestmoor blast zone may require PG&E gas line clearance procedures, which can add days to a schedule. We build that into the timeline up front rather than discovering it mid-dig. Second, the city’s rigorous post-2010 seismic requirements mean foundations and site work get a closer look than they might elsewhere – so slab prep near a retrofitted foundation needs to be done right the first time. Then there’s the fog belt itself: cool, damp air off the Pacific keeps driveways wet longer, so drainage and grip matter more than they would ten miles inland. If your project also touches the structure, homeowners often pair concrete work with a Garage Conversion ADU in San Bruno or a New Detached ADU in San Bruno, where a new apron or approach is part of the plan.
Serving San Bruno, CA – Our Local Coverage Area
We serve San Bruno and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Concrete Driveways & Concrete Work in San Bruno
A standard driveway in San Bruno takes three to five working days from demo to forms pulled, plus about seven days before you drive on it. Larger jobs, heavy demo, or PG&E clearance near Crestmoor can stretch that, and we tell you which applies before we start. Call (866) 320-2646 to get a timeline for your specific lot.
It depends on scope – a simple replacement at existing grade often doesn’t, while new driveways, grading changes, or work near utilities may require one. We confirm the requirement for your address before any concrete is poured. Call us and we’ll tell you straight whether your job needs a permit and what it involves.
All concrete cracks eventually, but proper subbase, correct thickness, and well-placed control joints keep cracking small and cosmetic rather than structural. That’s where the prep work earns its keep, especially in San Bruno’s damp coastal air. Call (866) 320-2646 and we’ll explain exactly how we’ll prep your slab.
Installation runs $4,500 – $12,000, and a full replacement with demo lands at $5,000 – $14,000. Size, finish, thickness, and drainage decide where you fall in that range. Call (866) 320-2646 for a written line-item estimate – it’s free.
Every concrete job we do is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. Backup support on the material side comes from partners like GAF and CertainTeed on adjacent exterior work. Call (866) 320-2646 to talk through coverage before you commit.
Get a Free Concrete Estimate in San Bruno
We’ll come out, measure the driveway, check the subbase and drainage, and hand you a written line-item estimate at no cost. You’ll know what you’re paying for demo, base, concrete, finish, and cleanup before a single bag of mix shows up. Our technicians bring up to 12 years of experience, and a live person answers the phone 24/7. Call (866) 320-2646 to schedule your free estimate for Concrete Driveways & Concrete Work in San Bruno.
Written by the team at Groundwork Construction Co.