Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cabinets & Countertops in Mill Valley, CA: What the Job Actually Involves
Replacing cabinets and countertops in Mill Valley typically runs $14,000 – $45,000 for a full tear-out and rebuild, and a standard kitchen takes three to five weeks from demo to final install. The work splits into two sequenced phases: cabinet boxes and doors first, then templated countertops cut to fit the installed cabinets, usually 5 – 10 days apart. Call (866) 320-2646 for a free on-site estimate. We measure the room, talk through door styles and stone choices, and put the number in writing before anything gets ordered.
How We Run a Cabinet and Countertop Job, Stage by Stage
Cabinet and countertop work isn’t one project. It’s two trades locked in sequence, and the gap between them is where schedules fall apart. Here’s how we keep them tight.
Stage 1: Site visit, measure, and material lock (day 1, about 90 minutes)
We photograph and measure the room, note where plumbing and electrical sit inside the existing cabinet run, and check the walls for plumb and square – on Mill Valley’s older hillside homes, walls are rarely straight, which matters when cabinets are set. You make your first big decisions here: door style, box material, countertop category. Nothing gets ordered until you’ve signed off on the line-item quote.
Stage 2: Ordering and lead time (2 – 5 weeks, mostly waiting)
Semi-custom cabinet lines typically run 15 – 25 business days. Stone slabs get selected and reserved at the yard, and the template can’t happen until the cabinets are in. This is the longest stretch, and it’s the one we plan your calendar around. You decide on hardware and pulls at this stage so they’re on hand the day the boxes are set.
Stage 3: Demo and prep (1 – 2 days)
Old cabinets come out, the room gets protected, and we address whatever the tear-out exposes. On a 1950s ranch in the flats off Miller Avenue, that’s often a warped subfloor or an old vent stack that needs a shift before the new boxes go in. Anything structural or plumbing-related gets flagged before we cut, not after.
Stage 4: Cabinet install (2 – 3 days)
Upper and lower cabinets get set, leveled, shimmed, and shimmed again – steep hillside homes settle, and a level box now saves a crooked drawer in two years. Crown molding, toe kick, and filler panels go in the same pass. You confirm hardware placement and pull locations as we go.
Stage 5: Countertop template, fabrication, and install (5 – 10 days after cabinets)
A fabricator lasers the finished cabinet tops, the slab gets cut, and the counter arrives about a week later. Sink cutouts and faucet holes are done at the slab, not in your driveway. Final install takes half a day, then a 24-hour cure before you use the sink.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Actually Make
Most of the decisions on a cabinet and countertop job come down to how long you want to live with each element and how much firmness you want in the materials. Here’s the honest trade-off for each.
- Cabinet box materials – plywood vs. particleboard. Plywood boxes hold screws better, survive moisture in a hillside home, and cost $1,500 – $3,000 more across a kitchen. Particleboard is fine in dry interiors but swells if a drain leaks. KraftMaid’s plywood line is what we spec most often here.
- Door style – framed vs. frameless. Frameless gives more usable interior and a modern look. Framed is more forgiving when walls are out of square, which is common in older Mill Valley stock.
- Countertop – quartz vs. granite vs. quartzite. Quartz (a Cambria-grade product) runs $60 – $120/sq ft installed, needs no sealing, and is the default for busy kitchens. Granite is $50 – $95/sq ft but wants resealing once a year. Natural quartzite looks striking but is harder and pricier – $90 – $140/sq ft – and chips if you slam a pot down.
- Countertop edge profile. A standard eased edge is included in the per-square-foot price. Ogee or beveled profiles add $15 – $40 per linear foot.
- Sink and faucet configuration. An undermount sink adds $200 – $500 in cutout work over a drop-in. Farmhouse sinks need a custom cabinet modification, which can add $400 – $900.
What Cabinets & Countertops Cost in Mill Valley, CA
The range we quote most often in Mill Valley is $14,000 – $45,000 for a combined kitchen cabinet and countertop replacement. That’s a real number, not a placeholder – the low end is stock-grade boxes with a modest quartz top; the high end is semi-custom cabinetry with a full-height quartzite slab and structural fixes.
Five variables push the number up or down:
- Cabinet line and door style. Stock vs. semi-custom is roughly a $4,000 – $9,000 swing.
- Room size and layout. A galley kitchen runs 30 – 40% less than an L-shaped layout with an island.
- Existing condition. Wavy walls, bad subfloor, or an old vent stack in the run add $1,500 – $4,000 in carpentry.
- Moving plumbing or electrical. Relocating a sink or dishwasher line adds $800 – $2,500.
- Permit scope. Cosmetic replacement usually doesn’t trigger a permit. Structural changes, gas line relocation, or electrical additions do.
Every written estimate we hand you itemizes cabinet line, slab material, fabrication, demo, install, and disposal. What’s not in the estimate unless spelled out: appliance removal, painting, and any repair we can’t see until demo. We tell you that up front, so the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Mill Valley Homes Do to a Cabinet and Countertop Job
Nothing here is off-the-shelf. Mill Valley sits on steep hillside lots threaded with narrow, tree-lined lanes, and a lot of the housing was built between the 1900s and the 1970s. That means old foundations, past unpermitted additions, and walls that have moved since they were framed. When we measure cabinets on Homestead Valley homes, we plan for wall bowing that pushes filler panels to half an inch instead of a quarter. On hillside properties off Miller Avenue and in the flats near downtown, single-lane access with no turnaround makes delivery of a full cabinet order a logistical job on its own – we schedule pre-dawn drop windows and send a spotter for the long trailer.
The climate adds a wrinkle. Marin’s wet winters and long dry summers cause wood cabinets to move seasonally, so we spec plywood boxes and finish the toe kick with moisture in mind. The city’s wildfire prevention rules touch even small remodels – non-combustible detailing and ember-resistant materials near exterior walls – so we account for that in what we order. Design review in Mill Valley is discretionary and site-specific, which means a cabinet job that involves exterior changes (a relocated window over the sink, a new vent) may need a planning sign-off. We pull the permits and coordinate the inspections so you don’t have to. This job is often part of a Kitchen Remodeling in Mill Valley, and when the scope widens, we scope it that way.
Serving Mill Valley, CA – Our Local Coverage Area
We serve Mill Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Cabinets & Countertops in Mill Valley
Plan on three to five weeks of active work once materials arrive, with two to five weeks of lead time before that for cabinet fabrication. The install itself is about five days; the rest is waiting on the stone. Call (866) 320-2646 to lock your dates.
Not usually – straight replacement of cabinets and counters is considered cosmetic in most Mill Valley kitchens. A permit is triggered when you move plumbing, add electrical, or change structure. We confirm the scope with the city before we start, and pull the permit if one’s needed.
Yes, and most Mill Valley jobs are done that way. If you keep the sink, dishwasher, and range in place, you avoid the plumbing and electrical rework entirely. The trade-off is cabinet configuration – the new boxes have to align with the existing rough-ins, which trims your layout options.
Most Mill Valley jobs land between $14,000 and $45,000 depending on cabinet grade, countertop material, and whether we uncover structural fixes. A stock-cabinet quartz job in a small kitchen sits near the low end. Call (866) 320-2646 – estimates are free and itemized.
Everything we install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. Cabinet and stone manufacturer warranties stack on top of that. You get the guarantee in writing before a single box arrives.
Get Your Cabinet and Countertop Estimate
If you’re pricing cabinets and countertops in Mill Valley, the fastest path is a free on-site estimate. We measure the room, walk through cabinet line and slab choices, and give you a line-item number in writing. Our technicians have up to 12 years of experience, and our calls are answered by a live person 24/7. Call (866) 320-2646 to schedule. Appointments available across Mill Valley and 94941. And if you’re also planning the bath, homeowners often pair this with Walk-In Showers & Shower Remodeling in Mill Valley or a Tub-to-Shower Conversion in Mill Valley.
Where We Serve in Marin
We work cabinet and countertop jobs across our Mill Valley service area, including Tamalpais-Homestead Valley, Corte Madera, Larkspur, and Tiburon. For the wider project scope – flooring, backsplash, layout changes – see our Kitchen Remodeling service. Whatever the trade, we hold the same 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co.