Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Larkspur, CA: What the Job Actually Involves
A wrought iron fence in Larkspur typically runs $3,500 to $9,000 and takes three to five working days on site, from layout and post-setting to final paint touch-up. Most of that time is spent on footings and finishing, not on hanging panels. If you’re replacing an old fence, add a half-day for demolition and haul-off. Call (866) 320-2646 for a free on-site estimate, and we’ll walk the property line with you before anything gets quoted.
How an Iron Fence Gets Built Here, Stage by Stage
Most contractors quote a fence as a lump sum and then disappear until the panels show up. Here’s the actual sequence we run, so you know what happens on day one versus day four.
Stage 1: Site walk and layout (day 1, about 2 hours). We mark the property line against your plat or survey, confirm setbacks, and check for irrigation lines, gas stubs, and the grade changes that hillside lots in Larkspur tend to hide. You decide the fence height, post spacing, and whether gates swing in or out. Anything buried that we can’t see gets flagged here, before digging starts.
Stage 2: Demolition and prep (day 1, half a day if there’s an old fence). Old panels, posts, and concrete footings come out and get hauled off. If the existing posts were set in concrete, pulling them is the slow part. You decide whether to reuse any sound masonry piers, which can save real money on a property with stone or stucco columns already in place.
Stage 3: Post footings and setting (day 2, full day). Posts go in at 6 to 8 feet on center, set in concrete footings sized to the height and wind load of the fence. On sloped ground, posts get stepped rather than racked so the panels stay level. This is the day the fence either lasts thirty years or starts leaning in three, so we don’t rush it.
Stage 4: Panels, rails, and gates (day 3, full day). Panels get hung, rails aligned, and gates fitted and adjusted. You walk the line with us before anything gets locked down. Any hardware choice – self-closing hinges, latches, a keyed gate – gets finalized at this point.
Stage 5: Finish, touch-up, and walkthrough (day 4, half a day). We touch up welds and paint, clean up the site, and do a final walkthrough with you. Any punch items get handled on the spot or scheduled within the week. The whole job is backed in writing by our 730-Day Done Right Promise – if it’s not right, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Choose Between
Iron fence is not one product. The choices below drive most of the price difference between a $3,500 run and a $9,000 one.
- Wrought iron vs. steel vs. aluminum. True wrought iron is heavy, hand-forged, and expensive; it’s the right call for a heritage downtown Larkspur property where authenticity matters. Fabricated steel is the standard for strength and value. Aluminum is lighter, won’t rust, and costs less, but it dents more easily and doesn’t read as “iron” up close. We usually steer homeowners to steel for the main run and aluminum only for lightweight ornamental sections.
- Powder-coat vs. painted finish. Powder coating holds up 15 to 20 years under Marin’s wet winters; field paint needs touch-up every three to five years. Powder coat costs more up front and saves the labor later – worth it near the coast.
- Height and spacing. A 4-foot picket fence costs meaningfully less than a 6-foot one, and tighter pickets cost more per foot. Pool code and privacy needs drive this decision, not aesthetics alone.
- Gates and hardware. A single walk gate is simple; a double driveway gate with self-closing hinges and a keyed latch adds real cost. Decide number of gates and swing direction early – retrofitting later means re-setting posts.
- Post finials, caps, and decorative panels. These are the “is this a $4,000 job or an $8,000 job” details. Add them where the fence faces the street; skip them on the back line if budget is tight.
What Iron Fence Costs in Larkspur, CA
Expect $3,500 to $9,000 for a typical residential iron fence in Larkspur. The range is wide because five things move it:
- Linear footage. Most of the cost lives here. Per-foot pricing on fabricated steel runs roughly $45 to $110 installed, so a 60-foot run lands near the bottom and a 150-foot run pushes the top.
- Height and gauge. A 6-foot fence in heavier gauge steel costs more than 4-foot lighter material, both in product and in footing size.
- Terrain and existing conditions. Hillside and canyon lots need stepped panels and sometimes small retaining work at the base. Old concrete footings add demolition time.
- Gates and automation. Each gate adds cost; driveway gates with operators add the most.
- Permits and HOA review. A permit or Design Review adds time and a fee, and some Larkspur properties are in review districts where that step can’t be skipped.
A written estimate from us lists line items: linear footage, height, gauge, finish, footing spec, gate count and hardware, permit fees, and haul-off. What it typically does not cover is underground surprises – a sewer lateral or irrigation main crossing the line – which we flag on the walkthrough and quote separately before digging. Upfront pricing, no surprises: the number on the estimate is the number you pay for the scope listed. Calls are answered by a live person, 24/7.
See the difference
Before
After
Before
After
Before
AfterWhat Larkspur Homes Specifically Do to This Job
Larkspur is a small, mostly built-out Marin town, and that changes iron fence work in ways it doesn’t change a new-build subdivision. The housing stock – early-1900s Victorians and bungalows along Magnolia Avenue, mid-century hillside homes, and a handful of newer infill – means most fences we build here go in beside an existing structure with a survey line that hasn’t been touched in decades. We start by confirming the line, because on an old lot the fence often ends up a foot or two off where the homeowner assumed. The town’s Design Review process scrutinizes exterior changes visible from the street far more than Corte Madera or San Anselmo does, so a front-yard or street-facing iron fence in Larkspur can require review before work starts, and we build that step into the schedule rather than letting it surprise you mid-job.
Hillside and canyon lots bring their own issues: grade changes, retaining walls, drainage that has to be worked around the fence base rather than through it. Marin’s wet winters also mean footing depth matters more than it does inland – a shallow footing that holds through August can heave by February. Fire-hardening is a real consideration too. Iron fence is non-combustible, which is one of the reasons it shows up more often than wood on properties being hardened for defensible space. This project sits alongside others on the same lot; many Larkspur homeowners pair it with Fence Installation in Larkspur as part of a full boundary and gate project, and if the driveway or walkway is being reworked at the same time, our Patios, Walkways & Pool Decks in Larkspur work is often scheduled alongside it so the base prep happens once. If a detached structure or unit is part of the plan, ADU Design & Permitting in Larkspur is where we handle the entitlement side. Our Fence Installation service covers the full range, and you can see the wider picture on our Larkspur service-area page.
Serving Larkspur, CA – Our Local Coverage Area
We serve Larkspur and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Larkspur
Most residential iron fences in Larkspur take three to five working days on site, plus whatever time permit or Design Review adds if required. The on-site work itself is typically one day for layout and demo, one for footings, one for panels and gates, and a half-day for finish and walkthrough. Call (866) 320-2646 for a scheduling estimate once we’ve seen the property.
It depends on height, location, and whether the property sits in a review district – front-yard and street-visible fences in Larkspur can require review that a back-line fence does not. Iron fence over a certain height near a corner or within a setback is the common trigger. We confirm the requirement during the site walk and pull what’s needed before work starts, so the fence isn’t built to a spec that fails inspection.
Often yes – sound existing footings and masonry piers can be reused, which cuts cost and demo time. We core-set or anchor the new posts into the existing concrete after checking it for cracks and movement. If the footing is failing, we replace it; that decision gets made on day one, not mid-job, and it’s reflected in the estimate.
Most iron fence projects in Larkspur land between $3,500 and $9,000, with the number driven mainly by linear footage, height, gauge, and gate count. A short 4-foot steel run with one walk gate sits near the bottom; a full-perimeter 6-foot fence with a driveway gate and decorative panels sits near the top. Call (866) 320-2646 for an exact quote – estimates are free.
Every iron fence we install is covered by the 730-Day Done Right Promise – if the workmanship fails, we come back and fix it. That covers installation, footing, and finish issues, and it’s in writing. If the fence isn’t done right, we make it right. Call (866) 320-2646 and we’ll walk you through exactly what the promise covers for your project.
Get a Free Iron Fence Estimate in Larkspur
The fastest way to know what your iron fence will cost is to have us out to the property. Call (866) 320-2646 to schedule a free on-site estimate – a live person answers, 24/7. We’ll confirm the property line, check the terrain and any review requirements, and leave you with a written line-item quote you can compare against anything else. No pressure, no surprises.
Written by the team at Groundwork Construction Co.