Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Corte Madera, CA: What It Involves and What It Costs
A wrought iron fence in Corte Madera typically runs $3,500 to $9,000 installed, with most residential runs landing in the middle of that range. The work usually takes three to five days from layout to final paint, plus a short gap if permits or an HOA review are in play. Iron fencing suits this town well: the housing stock mixes mid-century ranchers with newer two-story customs, and a clean black iron run frames both without shouting. Call (866) 320-2646 for a free on-site estimate.
How an Iron Fence Goes In: Stage by Stage
Iron fencing isn’t a dig-and-drop job. Posts carry real weight, gates swing on precise hinges, and a fence line that wanders looks wrong from the street. Here’s the sequence we follow on a typical Corte Madera property.
Stage 1: Layout and utility marking (day 1)
We walk the property line with you, set the corners, and confirm gate swing direction. We then call for utility location before anyone puts a shovel in the ground. On the flats near Corte Madera Creek, we also check where drainage swales run so a post doesn’t sit in the seasonal water path. You approve the final line and gate count this day.
Stage 2: Demolition and post holes (days 1-2)
If an old fence or failing retaining edge is coming out, that happens first – typically a half day for a standard residential run. Posts get set in concrete footings sized to our clay and fill conditions, which vary block to block. The holes cure overnight before any panels go up.
Stage 3: Setting posts and panels (day 3)
Once footings are firm, we set panels and check plumb on every post. Gates get hung and adjusted here. This is the stage where small grade changes show up; if your lot slopes, we adjust panel heights rather than forcing a level line that floats at one end.
Stage 4: Gate hardware and finish touches (day 4)
Hinges, latches, and any smart entry hardware go on. If you’ve chosen a powder-coat finish in a non-standard color, the factory coat arrives on the panels; we touch up welds and cut ends with matching paint so the finish reads uniform.
Stage 5: Final walkthrough and painting (days 4-5)
We do a final inspection with you, note any adjustments, and complete any field painting. Your signed walkthrough starts the 730-Day Done Right Promise. If anything isn’t right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Iron fencing isn’t one product. The choices below move both the look and the price.
- Mild steel vs. wrought iron. True wrought iron is largely historical now; most “iron” fencing sold today is mild steel. Steel is the practical choice – lighter, cheaper, easier to repair, and it holds powder coat well. Wrought iron costs more and is genuinely harder to source, but it earns its keep on estate and carriage-house properties with authentic period detailing.
- Powder coat vs. field paint. Factory powder coat is the durable option, usually black, occasionally bronze or a matched color. Field paint costs less upfront but needs re-coating every few years in our wet-winter climate. For most homeowners, powder coat wins the long game.
- Panel heights and picket spacing. A 4-foot fence reads as a garden boundary; 5 to 6 feet gives more privacy and security. Closer picket spacing raises material and labor; keep spacing tight only where you need it.
- Gate style and automation. Swing gates are standard; sliding gates suit tight drives. If you want a keypad, intercom, or smart-home tie-in, plan for it now – the conduit and hardware mounting have to be designed before the posts are set. Brands like ViewLux or Therma-Tru show up on gate accessories and hardware in higher-end projects, and choosing a known name matters for long-term parts availability.
- Finials and decorative detail. Spear tops, scrollwork, and custom finials add character but push cost. Simple flat-top designs are cleaner and cheaper; ornate finials belong on homes where the architecture supports them.
What Iron Fence Costs in Corte Madera, CA
Expect $3,500 to $9,000 for a residential iron fence here. The low end fits a short run with a simple flat-top design and no gate automation. The high end covers longer runs, ornate detailing, and integrated gate hardware.
Five variables push the number up or down:
- Linear footage. The single biggest driver. A 40-foot run and a 120-foot run are different jobs, even at the same finish.
- Existing fence and site conditions. Removing an old fence, cutting through hardscape, or dealing with rocky or poorly draining soil adds labor.
- Material grade and finish. Powder coat over a standard steel profile is the baseline. Wrought iron, custom colors, and ornate finials raise the floor.
- Gates and automation. Each gate adds hinge and latch labor. Automated gates with keypads or intercoms add hardware plus wiring.
- Permit scope. A fence under six feet on a standard lot usually needs no permit in Corte Madera. Taller fences, fences in the flood-zone flats, and fences on hillside lots with retaining walls can require a permit and inspection. That adds a step and a small fee.
Our written estimate itemizes linear footage, post count, gate count, finish, and any demolition. It doesn’t include landscaping repair after installation or custom masonry piers, which we quote separately if you want them.
See the difference
Before
After
Before
After
Before
AfterWhat Corte Madera Homes Specifically Do to This Job
Corte Madera sits where Marin’s flood plain meets its hillsides, and that split shapes iron fence work here. On the low-lying flats near Corte Madera Creek and the Town Center, ground can stay saturated through wet winters. Posts set shallow in that soil will heave and lean within a season. We set deeper footings on the flats and check drainage before we commit a line. On hillside lots above town, the challenge is grade – fence lines step down a slope, and a fence running near a retaining edge needs its own engineering so the posts don’t load the wall. Properties in ZIP codes 94925 and 94976 carry both conditions. The mid-century and newer custom homes we work on here often pair an iron fence with a gate or entry feature, and homeowners often pair this with Patios, Walkways & Pool Decks in Corte Madera so the hardscape and fence line read as one design. If part of the project is a full Fence Installation in Corte Madera scope, we’ll plan the iron run alongside it. Our technicians have up to 12 years of experience, and we cover Corte Madera with the same Fence Installation standard we bring everywhere. If your property also includes a detached structure or addition, homeowners often pair this with ADU Design & Permitting in Corte Madera.
Serving Corte Madera, CA – Our Local Coverage Area
We serve Corte Madera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in Corte Madera
Most residential iron fence jobs take three to five working days from layout to walkthrough. Short runs with no gates can finish in three; longer runs with automated gates and permit review stretch to five or more. Call (866) 320-2646 for a firm timeline on your property.
Usually not, if the fence is under six feet and on a standard lot. Fences over six feet, or fences on flood-zone flats near the creek or on hillside lots with retaining walls, may need a permit and inspection. We check the requirement for your specific parcel before work starts. Call (866) 320-2646 to confirm.
In most cases, yes. Post holes are small and shallow compared with foundation work, and we locate utilities before digging. If your fence line crosses a buried line, we adjust the post layout rather than risk the utility. We flag any conflict during layout so nothing is a surprise. Call (866) 320-2646 for a site check.
Most jobs land between $3,500 and $9,000, depending on linear footage, finish, and gate hardware. Powder-coat finishes and automated gates push toward the high end; simple flat-top runs stay near the low end. Call (866) 320-2646 for an exact, itemized quote – estimates are free.
Every project is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees we offer. If something isn’t right within that window, we make it right. Material warranties from manufacturers stack on top. Call (866) 320-2646 to schedule your free estimate.
Schedule Your Free Iron Fence Estimate
We’ll walk your property with you, confirm the fence line, talk through finish and gate options, and leave you with a written, itemized estimate. Free, no pressure. Calls are answered by a live person 24/7, so you’re never sent to voicemail. Call (866) 320-2646 to schedule your free iron fence estimate in Corte Madera, and we’ll go from there.
Written by the team at Groundwork Construction Co.