Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vinyl Fence Installation in Tamalpais-Homestead Valley, CA
A vinyl fence in Tamalpais-Homestead Valley typically runs $3,500 – $9,000 installed, with most residential jobs landing between $4,200 and $7,000. Plan on two to four days on site once materials are on the property, longer if the run follows a slope. Call (866) 320-2646 for a free on-site estimate; we’ll measure the actual footage, look at the grade, and give you a written number before any work starts.
How a vinyl fence goes in here, stage by stage
Every vinyl job here follows the same sequence. What changes is how much time the grade and the access add. Tamalpais-Homestead Valley lots sit on slopes, and that reality shows up in step two more than anywhere else.
Stage 1: Site visit and layout (day 1, roughly 90 minutes)
We walk the property line with you, measure total footage, and flag anything that changes the run: a grade break, a retaining wall, a mature redwood root zone, a gate location. You decide the fence height, the panel style, and where the gate or gates go. If the line needs to be verified against a survey, that gets sorted before we order anything. Nothing is ordered until you sign off on the layout.
Stage 2: Digging and setting posts (day 1 into day 2)
Vinyl posts carry the load, so the footings matter more than the panels. On sloped ground we step the fence in sections rather than raking panels to follow the hill, which keeps the post holes square and the loads even. Posts get set in concrete and cure overnight on a standard run. On the shaded north-side slopes, where the ground stays wet well into spring, we pay close attention to drainage at each hole so a post doesn’t sit in standing water.
Stage 3: Rails, panels, and trimming (day 2 into day 3)
Rails snap into the posts, panels slide in, and the top rail caps the section. This is the fast part when the footprint is level and the slow part when it isn’t. You’ll see the fence take shape quickly here. Trim pieces at corners and end posts finish the run, and we cut around any fixed obstacle rather than leaving a gap.
Stage 4: Gates and hardware (day 3)
Gates get hung, hinged, and aligned. You walk through the swing and the latch with us and tell us if it needs adjusting before we call it done. Vinyl gates need the right post reinforcement on the hinge side, especially at four-foot widths and up, so this stage gets its own pass rather than getting rushed at the end of the panel work.
Stage 5: Cleanup and walkthrough (day 3 or 4)
We haul away spoils, sweep the line, and walk the finished fence with you. Every post, panel, and gate gets checked. You get the warranty in writing. If anything needs a return trip, we schedule it before we leave the driveway.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between
Vinyl isn’t one product. What you pick here sets the price and how the fence looks in ten years.
- Privacy panel vs. picket vs. semi-privacy. Full privacy (six-foot solid) is the most common choice for backyards and runs $35 – $55 per linear foot installed. Picket and semi-privacy run less, around $25 – $40 per linear foot, and suit front yards where you want definition without a wall.
- Standard vinyl vs. reinforced profiles. Standard hollow posts are fine on flat ground and short runs. On longer runs, or anywhere a gate hangs, reinforced posts and rails cost 10 – 20% more and hold alignment far better over time.
- Color and finish. White is the cheapest and most available. Tan, gray, and woodgrain textures cost more and hide dirt and shade-side grime better on the damp north slopes here.
- Height. Four, five, and six foot are the standard heights. Six foot adds privacy and wind load, which matters on exposed ridge lots.
- Gate count and width. Each gate adds hardware, reinforcement, and time. A double gate for vehicle access costs meaningfully more than a single walk gate.
We only quote brands we stand behind. On the fencing side, that’s a short list of manufacturers whose profiles we’ve installed and know hold up.
What Vinyl Fence costs in Tamalpais-Homestead Valley, CA
Most vinyl fence work in Tamalpais-Homestead Valley lands between $3,500 and $9,000 for a residential run. Here’s what moves the number:
- Linear footage. The single biggest driver. 100 feet of six-foot privacy fence sits near the middle of the range; 200 feet pushes the top.
- Grade and terrain. Stepped runs on a slope take more posts, more concrete, and more time than a flat run of the same length.
- Post and panel grade. Reinforced profiles and woodgrain textures add cost. Standard white on flat ground is the low end.
- Gates. Each gate adds hardware, hinge-side reinforcement, and labor. A double gate is a bigger jump than people expect.
- Access and staging. Narrow winding lanes in the valley can limit where a truck parks and how far material gets carried. Long carries add labor, and this is a real line item here, not a theoretical one.
Our written estimate is line-item: footage, post count, panel grade, gates, and cleanup, priced upfront so the number you see is the number you pay. What isn’t included: survey work if the property line is unclear, removing large stumps or rock in the post line, and any grading needed to make the run workable. We flag those before we start, never after.
See the difference
Before
After
Before
After
Before
AfterWhat Tamalpais-Homestead Valley homes specifically do to this job
This is an unincorporated community, so a fence here runs through County of Marin permitting, not a city building department. That’s the first thing that surprises homeowners. It also means the permit timeline and inspection expectations follow County rules, and we pull the permits and pass the inspections rather than handing that back to you.
The lots are the second thing. Steep, wooded hillside parcels with dense redwood cover mean posts land in root zones, runs break around grade, and drainage at each footing has to be thought through. On the shaded north-facing slopes, ground stays damp well into spring, so we set footings with water in mind, not just depth. Narrow private lanes mean staging takes planning, and long material carries are sometimes unavoidable. None of that is unusual here; it’s just part of how the job gets done in Tamalpais-Homestead Valley.
We see the same failure modes on older fences: posts that went shallow and heaved, panels that warped after a wet winter, gates that sagged because the hinge post was never reinforced. If your current fence is on its way out and the driveway needs attention too, homeowners often pair a new fence with Driveway Repair & Replacement in Tamalpais-Homestead Valley, since access and staging overlap. As part of a full Fence Installation in Tamalpais-Homestead Valley project, we can handle the whole line, gates included, and if the driveway itself needs resurfacing, that’s covered by our Asphalt Driveways & Resurfacing in Tamalpais-Homestead Valley work. We cover all of Tamalpais-Homestead Valley and nearby Mill Valley, Corte Madera, Larkspur, and Tiburon. For the wider scope of our Fence Installation service, that page lays out the full picture.
Serving Tamalpais-Homestead Valley, CA – Our Local Coverage Area
We serve Tamalpais-Homestead Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Vinyl Fence in Tamalpais-Homestead Valley
Most residential vinyl fence jobs take two to four days on site after materials arrive, with ordering lead time of one to three weeks ahead of that. Sloped runs, extra gates, and narrow-lane access push toward the longer end. Call (866) 320-2646 for a timeline tied to your actual footage.
In unincorporated Tamalpais-Homestead Valley, fence permits go through County of Marin, and the requirements depend on height, location, and whether the run affects drainage. We pull the permits and handle the inspections as part of the job. Call us and we’ll tell you what your specific run needs before you commit to anything.
No, not on a written line-item estimate. The number you sign is the number you pay, with change orders only if you add scope or if we hit something we flagged in advance (a buried stump, rock, or unmarked utility). Call (866) 320-2646 for an exact quote; estimates are free.
Yes, in most cases. Posts are set individually and stepped to grade, so the fence follows the hill rather than fighting it, and we set footings with drainage in mind. Anything that would require regrading or a retaining wall gets flagged at the site visit, not mid-job. Call us to walk the line on your property.
Every vinyl fence we install is backed by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That’s on top of the manufacturer’s warranty on the vinyl profiles themselves. Call (866) 320-2646 and we’ll walk you through both in plain terms.
Get a free vinyl fence estimate in Tamalpais-Homestead Valley
Call (866) 320-2646 to schedule a free on-site estimate. We’ll measure the run, look at the grade and access, and give you a written line-item price with the permit scope spelled out. Calls are answered by a live person around the clock, and every job is backed by the 730-Day Done Right Promise. No pressure, no surprises, just a number you can plan around.
Written by the team at Groundwork Construction Co.