Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Corte Madera, CA
A tub-to-shower conversion in Corte Madera typically runs $3,500 to $10,000 and takes three to five working days once materials are on site. The job means pulling the old tub and its surround, reworking the drain and waterproofing, setting a new shower base or a curbless pan, tiling the walls, and hanging glass. Most Corte Madera homes we open up are 1950s to 1970s builds, so the real variable is what sits behind the tub wall. Call (866) 320-2646 for a free on-site estimate before you commit to anything.
How the conversion actually runs, day by day
Every conversion follows the same sequence. The dates shift with material lead times, but the order never does.
- Stage 1 – Site protection and demo (day one, 4 to 6 hours). We mask the room, shut the water at the fixture stops, disconnect the drain, and cut the tub out in sections. Cast iron goes out heavy; fiberglass and acrylic come out fast. You decide at this point whether the original tub gets hauled away or set aside for a future project. This is also when we open the wall and see what’s actually there.
- Stage 2 – Rough plumbing and framing (day one into two, 4 to 8 hours). The old drain gets reworked to the new shower location, the valve gets replaced or rebuilt, and any rot or soft framing gets sistered in. If the wall behind the tub is drywall rather than cement board, it comes down here. You approve the valve and trim choice before we close anything up.
- Stage 3 – Waterproofing and inspection (day two, 3 to 5 hours plus drying). We install a bonded waterproofing membrane or a cement board assembly with a liquid-applied membrane, then flood-test the pan where local inspection requires it. Membrane needs to cure before tile. This is the stage that separates a shower that lasts twenty years from one that leaks in three.
- Stage 4 – Tile and setting (days three and four, 1.5 to 2 days). Wall tile, grout, niche, curb, and the shower floor. Large-format porcelain goes up quicker than small mosaic; a herringbone or subway pattern takes longer. You pick grout color and sealer here, and we schedule the glass template.
- Stage 5 – Glass, trim, and walkthrough (day five, 4 to 6 hours). Frameless or semi-frameless enclosure goes in, fixtures get set, caulk line gets run, and we walk the room with you. Cure time for silicone is 24 hours before first use.
Our technicians have up to 12 years of experience, and the crew that cuts your tub out is background-checked and arrives in uniform.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices you’ll actually make
By the end of day two you’ll have picked your base, your wall material, your valve, and your glass. Here’s the honest trade-off on each.
- Shower base: acrylic pan vs. tiled pan. Acrylic is the value pick, around the low end of the range, and cleans in seconds. A tiled mud-set pan costs more but lets you match the floor to the wall and go curbless if you want.
- Wall material: porcelain large-format vs. ceramic subway vs. stone-look. Large-format porcelain is the current go-to in Corte Madera, fewer grout lines and quick to clean. Subway is classic and cheap to replace but shows grout over time. Stone-look panels sit between the two on price.
- Valve and trim: rebuild the old vs. replace vs. pressure-balance upgrade. Rebuilding saves money if the body is sound. Replacing with a pressure-balancing cartridge is the right call in a house from the 1960s or 70s, where the original valve has usually been limping along for decades. Kohler and Moen trims are the ones we specify most.
- Glass: framed vs. semi-frameless vs. frameless. Framed is the budget option and reads builder-grade. Semi-frameless hides the hardware. Frameless is the finished look and prices accordingly, and we template it after tile so the fit is tight.
- Curb vs. curbless. A curb keeps the code-mandated waterproofing simple. Curbless requires the joists to be recessed or the floor built up, which means a structural line item before tile is ordered.
What a tub-to-shower conversion costs in Corte Madera, CA
The number for this job lands between $3,500 and $10,000. Here’s what pushes a project toward either end.
- Size and configuration. A standard 60-inch tub footprint is the cheapest to convert. A wider alcove or an L-shaped layout adds tile and pan square footage.
- Existing condition. Rot, a failed valve, or a floor that’s out of level all add repair hours before tile goes up.
- Plumbing and electrical moves. Keeping the drain in the same spot is the biggest saver. Moving it, or adding a niche light or exhaust fan, requires a permit amendment and a trade.
- Material grade. Acrylic pan with standard porcelain keeps you low. Frameless glass, tile to the ceiling, and a bench push the job to the top of the range.
- Permit scope. A straight fixture swap with no plumbing move may not require a permit. A valve relocation or a structural change does, and that adds inspection time and cost.
A written estimate from us is line-item: demo, rough plumbing, waterproofing, tile, glass, and permit. It does not include the fixture cost unless you buy through us. It also doesn’t cover hidden damage discovered after demo, which is why we price the inspection before we commit to a final number. The number you see is the number you pay, and every project carries a 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Corte Madera homes specifically do to this job
Corte Madera isn’t one housing market, it’s two. The flats near Corte Madera Creek and the Town Center area sit in a FEMA flood zone, so any remodel that touches the structure, including a shower that goes to the joists, can trigger an elevation check and a drainage plan. The hillside lots above town face a different problem: a wet winter on a slope means the bathroom floor framing often needs sistering, and a curbless shower in a hillside home can require joist blocking and a structural sign-off. We see it most in the older ranchers and split-levels from the 1950s to 70s, where the original tub surround has been quietly leaking for a decade and the subfloor behind it is soft. The 94925 and 94976 ZIPs both carry this mix. This is also where a bathroom update often pairs with a wider scope – a full Bathroom Remodeling in Corte Madera – or with exterior work like Metal Roofing in Corte Madera when a storm-damaged house gets rehabbed top to bottom. We work the whole town, and our Corte Madera service page covers the rest of our scope.
Serving Corte Madera, CA – Our Local Coverage Area
We serve Corte Madera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Tub-to-Shower Conversion in Corte Madera
Three to five working days on site, plus two to four weeks before that for material lead time and any permit review. The tile and waterproofing are the slow stages; the demo is fast.
It depends on whether you’re moving the drain, the valve, or the structure. A straight fixture swap in the same spot often doesn’t require one; a plumbing relocation or a curbless conversion usually does, and in the flood-zone flats the review can add elevation and drainage requirements. We pull the permits and pass the inspections as part of the job.
Yes, and it’s the cheapest way to do it. Keeping the original drain location and rebuilding the valve at the same spot usually keeps the job in the $3,500 to $6,000 band. Moving the drain or going curbless pushes the number up.
Between $3,500 and $10,000 depending on size, material grade, and how much hidden damage turns up after demo. The high end covers frameless glass, tile to the ceiling, and a plumbing move. Call (866) 320-2646 for an exact quote – estimates are free.
Every conversion is covered by our 730-Day Done Right Promise. If the waterproofing, tile, or setting isn’t right, we come back and make it right. It’s one of the longest workmanship guarantees in residential construction.
Get a free estimate on your tub-to-shower conversion
Call (866) 320-2646 to schedule a free on-site estimate for a tub-to-shower conversion in Corte Madera. We look at the tub footprint, the drain location, the wall behind the surround, and any flood-zone or structural consideration before quoting. You get a written, line-item number with the permit scope stated. We can also quote this as part of a broader Bathroom Remodeling scope if you want the vanity and fixtures done in the same pass.
Written by the team at Groundwork Construction Co.