Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tub-to-Shower Conversion in Sonoma, CA: What It Costs and How Long It Takes
A tub-to-shower conversion in Sonoma typically runs $3,500 – $10,000 and takes 5 to 10 working days from demo to final inspection. The job means pulling the tub and its surround, reworking the drain and valve to shower position, waterproofing the wet zone, setting a new shower pan and walls, and hanging glass or a curtain rod. Call (866) 320-2646 and we’ll walk your specific bathroom and give you a written, upfront price before anything gets ordered.
How the Work Actually Runs, Stage by Stage
This isn’t a swap. A tub-to-shower conversion changes the geometry of a wet room, and the order of operations matters more than the finish selections. Here’s the sequence we run, and where you’ll be asked to make a call.
Stage 1: Site check and measurements (day 1, about 2 hours)
Before demo, we confirm what’s behind and below the tub: floor joist direction and depth, the existing drain size and trap location, the valve rough-in, and whether the alcove is truly square. In older Sonoma homes, this is where surprises show up. You’ll decide then whether we’re keeping the current drain location or moving it, which affects the next stage.
Stage 2: Demo and rough-in (days 2 – 3)
Out comes the tub, the surround, and any rotten subfloor or greenboard. If we’re relocating the drain to center the shower pan, that’s a day of plumbing rough-in and a subfloor repair. You’ll choose the pan size here, because a 60-inch tub alcove almost always becomes a 48- or 60-inch shower base and the difference changes your glass order.
Stage 3: Waterproofing and inspection (days 4 – 5)
We set the pan, seal the seams, and apply a bonded waterproofing membrane to the walls, then flood-test the pan. If the local jurisdiction requires a rough plumbing inspection, it happens before tile goes up. This is the stage where a cheap job cuts corners and a real one doesn’t.
Stage 4: Tile, trim, and glass (days 6 – 9)
Wall tile, grout, valve trim, and the showerhead go in, then the glass gets templated and installed about a week after tile so the framing is settled. You’ll finalize tile and trim selections back in Stage 2, so the order is on site when we need it.
Stage 5: Final walkthrough (day 10)
We test the drain, check the pan for ponding, inspect the glass for alignment, and walk the whole bathroom with you. Any punch item goes on a written list and gets handled under the 730-Day Done Right Promise. If it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
You’ll make four decisions, and each one moves the price. Here’s the honest trade-off:
- Shower base vs. tiled pan: A prefab acrylic or fiberglass base is the cheaper, faster option and holds up well, but it reads builder-grade. A tiled mortar pan with a linear drain looks custom and costs $1,200 – $2,500 more, and needs a contractor who knows how to slope it. We do both.
- Acrylic surround vs. tile walls: Acrylic panels go up in a day, never need grout sealing, and cost less. Ceramic or porcelain tile gives you the look that matches a Sonoma wine-country estate, but plan on sealing grout and repointing every several years.
- Glass door vs. fixed panel vs. curtain: A frameless glass door is the premium choice and the easiest to clean, running $900 – $1,800 for the enclosure. A fixed half-panel or a curtain rod is half the cost and works fine on a smaller alcove.
- Valve and fixtures: Kohler and similar mid-tier brands sit in the middle of the pack on price and reliability. You can spend a lot more or a lot less here, and it’s the easiest line to trim if the budget is tight.
Cabinet and vanity decisions come up too if the bathroom is being refreshed at the same time, and KraftMaid is a solid mid-point choice when we’re pairing a new shower with a new vanity.
What Tub-to-Shower Conversion Costs in Sonoma, CA
Most jobs land between $3,500 and $10,000. That range isn’t a hedge; it reflects the real spread between a basic acrylic swap and a tiled, glassed, custom-pan conversion. Here’s what pushes the number to either end:
- Existing condition ($0 – $2,000+): Rotten subfloor, water-damaged framing behind the tub, or an undersized drain line is the single biggest swing. A clean alcove means a simple job.
- Plumbing relocation ($400 – $1,500): Keeping the drain where it is saves money. Centering the drain for a larger pan means moving it, plus a subfloor repair.
- Material grade ($1,000 – $3,500): The difference between acrylic and porcelain tile with a custom pan and frameless glass.
- Permit scope ($200 – $800): Some jurisdictions require a plumbing or building permit for the drain relocation and rough-in work. We pull permits when they’re needed and pass the inspection.
- ADA or accessibility features ($500 – $1,500): Zero-threshold entry, grab bars, and a bench add to both price and useful life.
A written estimate from us lists the demo, rough-in, waterproofing, tile, glass, fixtures, permit, and cleanup as separate lines, so you can see exactly what you’re paying for. Not included: structural repairs discovered mid-demo, HOA fees, and anything you ask us to add after the contract is signed. Upfront pricing, no surprises. Call (866) 320-2646 for an exact quote, and estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Sonoma Homes Specifically Do to This Job
The near-Plaza historic district is the first thing that changes this bathroom job. Several downtown and near-Plaza homes are 19th-century adobe, Victorian, or Edwardian construction with raised foundations, and some carry unpermitted later additions. When we cut into the wall around an existing tub in one of these homes, we sometimes find original adobe or early-framing walls behind the modern finishes, and the job stops for a redesign review. That’s a real possibility on these blocks, not a scare tactic. If your home is inside the 1968-designated Plaza district, exterior changes may need City of Sonoma Historic Preservation Commission review, and interior plumbing work may need a permit before we can close up the walls. Outside city limits, on the wine-country estates and hillside parcels, the shower drain ties into a septic system rather than a municipal sewer, so we confirm the drain line and vent run before we commit to a pan layout. The seasonal clay soils on the Sonoma Valley floor also heave, which can crack a shower pan set on an unlevel floor – we check the subfloor for level before we set anything. If your project grows into a full bathroom scope, that’s a different page (our Bathroom Remodeling in Sonoma page covers it), and the wider picture lives on our Bathroom Remodeling hub. We serve the whole Sonoma area, and homeowners often pair this job with Metal Roofing in Sonoma or Tile Roofing in Sonoma when a roof project is on the list.
Serving Sonoma, CA – Our Local Coverage Area
We serve Sonoma and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Tub-to-Shower Conversion in Sonoma
Plan on 5 to 10 working days, with 7 as the typical number. The demo and rough-in take 2 days, waterproofing and inspection take 1 to 2 days, tile and glass take the rest, and glass tempering usually adds about a week between template and install. Call (866) 320-2646 for a schedule based on your bathroom.
Usually yes if we’re moving the drain or changing the plumbing rough-in. A pure surface swap with no plumbing moved may not require one. We confirm the requirement for your address, pull the permit when it’s needed, and pass the inspection. Call (866) 320-2646 and we’ll tell you which side of the line your job falls on.
Yes, and it’s the most common version. Keeping the drain and valve where they are and dropping a 60-inch shower pan into the existing tub alcove avoids any framing changes and keeps the job at the low end of the range. Call (866) 320-2646 if you want to know whether your existing alcove will take that configuration.
Most jobs run $3,500 to $10,000. Basic acrylic with the existing plumbing stays near the low end; tiled walls, a custom mortar pan, frameless glass, and a drain relocation land near the top. Call (866) 320-2646 for an exact quote, and estimates are free.
Every tub-to-shower conversion we do is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship on the pan, waterproofing, tile, and plumbing. Calls are answered by a live person, 24/7, and our technicians are background-checked and arrive in uniform.
Get a Free Estimate for Your Tub-to-Shower Conversion in Sonoma
The best next step is a free on-site estimate. Call (866) 320-2646, and a live person answers. We’ll look at your bathroom, measure the alcove and check the subfloor, and give you a written, line-item price for the tub-to-shower conversion you want, with no pressure and no change orders later. Our technicians have up to 12 years of experience on work like this, and we back the work with the 730-Day Done Right Promise. Projects over $10,000 qualify for $1,000 off, and 0% financing for 18 months makes a bigger scope easier to budget. We’ll see you on site.
Written by the team at Groundwork Construction Co.