Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Corte Madera, CA: What It Actually Takes
Asphalt driveways & resurfacing in Corte Madera typically run $3,500 – $9,000 for a full new asphalt driveway and $250 – $700 for a reseal, with most residential jobs wrapping up in two to four days once the weather cooperates. A genuine resurfacing (a new wearing course over sound base) costs less than a full tear-out, but only when the base is still holding. Call (866) 320-2646 and we’ll tell you which one your driveway actually needs.
What most Corte Madera homeowners discover is that the answer depends less on the asphalt than on what’s under it – and in this town, that’s where it gets interesting.
How We Run an Asphalt Job, Start to Finish
Every asphalt driveway we build follows the same five stages. What changes is how much time each stage takes, and that comes down to your specific slope, drainage, and base condition. Here’s the real sequence, not a marketing summary.
Stage 1: Site Evaluation and Drainage Mapping (Day 1, 1 – 2 Hours)
Before anything gets torn up, we walk the site and figure out where water wants to go. Corte Madera’s wet winters mean a driveway that doesn’t shed water properly will fail from below, regardless of how good the asphalt on top is. We check existing slope, look for low spots, and confirm where runoff can legally discharge – especially on lots near the marsh and creek flats where grading rules are tight. This is also when you decide whether we’re resurfacing over an existing base or starting fresh.
Stage 2: Demo and Base Prep (Day 1 – 2, 4 – 8 Hours)
If we’re doing a full replacement, the old surface comes out and gets hauled away. If we’re resurfacing, we mill or clean the existing surface so the new course bonds properly. Then comes the part nobody sees and everybody should care about: grading the sub-base, compacting it in lifts, and building the crushed-stone base to the right depth. On Corte Madera’s hillside lots, this stage often includes adjusting the grade to manage runoff before a single ton of asphalt shows up. A shallow base here is the number-one reason driveways crack within three years.
Stage 3: Asphalt Placement and Compaction (Day 2 – 3, 3 – 6 Hours)
Hot-mix asphalt gets laid at the right temperature and compacted with a roller in passes until it hits target density. For a standard residential driveway that’s typically 2 to 3 inches of compacted asphalt over 4 to 6 inches of base, deeper on soft or sloped ground. You’ll want to decide your thickness and mix during the estimate, not on install day. Thin lifts laid too cool are the other big failure cause, and you can’t fix them later.
Stage 4: Edging, Drainage, and Finishing (Day 3, 2 – 4 Hours)
Edges get shaped and supported so the asphalt doesn’t ravel at the borders. If your job needs a channel drain, catch basin, or a swale to move water off the flats, it goes in here. On the low side of town, drainage detail is often the difference between a driveway that lasts and one that turns into a puddle every January.
Stage 5: Cure and Seal (Day 4, Plus a 6 – 12 Month Wait)
Fresh asphalt needs to cure before heavy traffic – typically 3 to 7 days for vehicles, longer for anything heavy. Sealing is the one thing you don’t do right away: new asphalt should cure for 6 to 12 months before its first seal coat, then reseal every 2 to 3 years after. That schedule is the single biggest factor in how long the surface lasts, and it’s a decision you make on day one even though the work happens a year later.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Every asphalt driveway in Corte Madera comes down to a few decisions. Here’s what each one costs you in money and durability, honestly.
- Full replacement vs. resurfacing. A tear-out runs $5,000 – $14,000 and resets the clock on base and surface. Resurfacing over a sound base costs less but only works if the sub-base and drainage are still intact – if the cracks are structural, resurfacing just hides a problem for a year or two.
- Asphalt thickness and base depth. Standard residential is 2 – 3 inches of asphalt over 4 – 6 inches of base. Going deeper on soft ground or a steep slope costs more up front and prevents the rutting and cracking that shallow builds get.
- Hot-mix grade. Standard mixes handle most driveways. A coarser, higher-binder mix holds up better under heavy vehicles or on a grade, at a modest cost bump.
- Drainage hardware. A channel drain or catch basin is a line item, not a freebie. On a flat creekside lot it’s often non-negotiable and worth every dollar.
- Edging material. Asphalt, concrete curb, or paver edging at the borders. Concrete curb holds the edge best on slopes; paver edging is the finish choice if the driveway meets a landscaped bed.
- Seal coat timing. Skipping the first-year seal is a false economy. Plan on the seal schedule as part of the project, not an afterthought.
If your project grows into a wider hardscape plan, that’s where our Driveway & Pavers service picks up, and the material choices multiply from there.
What Asphalt Driveways & Resurfacing Costs in Corte Madera, CA
Asphalt driveways & resurfacing in Corte Madera generally fall between $3,500 and $9,000 for new asphalt paving, $250 and $700 for sealing, and $5,000 – $14,000 if the job turns into a full driveway replacement with new base. Resurfacing lands in the middle of that spread depending on how much prep the existing surface needs.
Five things push a Corte Madera job toward the high end:
- Size and slope. A long, steep hillside drive needs more asphalt, more base, and more compaction time than a short flat one.
- Base condition. Soft or failed sub-base means excavation and hauling, which is where budgets move fast.
- Drainage scope. Channel drains, catch basins, and regrading on the flood-zone flats add real cost – but skipping them is more expensive later.
- Access and haul-off. Tight lots near the creek flats or a narrow hillside approach slow demo and material delivery.
- Permits. Work that touches flood-zone grading or changes drainage can require plan review, and that adds time and fees.
A written estimate from us lists base depth, asphalt thickness, drainage items, and disposal as separate line items, so you can see where the number comes from. Upfront pricing, no surprises – the number you see is the number you pay, and it’s backed by our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Corte Madera’s Terrain Does to This Job
Corte Madera sits on a split that no hillside town nearby has to deal with. The low-lying flats near Corte Madera Creek and the Town Center sit in designated flood zones, so driveway work there routinely runs into flood-elevation and drainage requirements – grading plans, raised grades, and runoff that has to be accounted for in a way Mill Valley jobs never touch. Driveway depth, slope, and drainage detail become permit questions, not just design preferences, when your lot drains toward the marsh. We plan for seasonal flooding in those areas as a baseline, not an exception.
Blocks away, the hillside lots above town are a different job: slope stability, water running down the drive during heavy rain, and base prep that has to hold on ground that wants to move. The 1950s – 70s ranchers and split-levels we work on across ZIPs 94925 and 94976 often have original driveways that were never built for today’s water load. When we’re regrading a drive as part of a full Driveway & Pavers in Corte Madera plan, the drainage call usually gets made here first.
Serving Corte Madera, CA – Our Local Coverage Area
We serve Corte Madera and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Asphalt Driveways & Resurfacing in Corte Madera
Most residential asphalt driveways in Corte Madera take two to four working days from demo to final compaction, plus a 3 – 7 day cure before you park on it. Weather is the wildcard – asphalt can’t be laid in the rain, and Corte Madera’s wet winters mean we schedule around the forecast. Call (866) 320-2646 for a realistic timeline on your specific lot.
It depends on whether the work changes grading or drainage, and that’s especially true on the flood-zone flats near the creek and Town Center. Simple resurfacing often needs no permit; regrading or new drainage on a flood-zone lot can trigger plan review. We confirm what your project requires before we quote, so there are no surprises mid-job.
Only if the base and drainage are still sound – resurfacing over structural cracks just hides the problem for a season or two. We inspect the base during the estimate and tell you straight which option makes sense. Call (866) 320-2646 for a free on-site look.
Resurfacing typically falls between $3,500 and $9,000 in Corte Madera, landing lower than a full replacement when the base is intact. Base condition, size, and drainage scope move the number most. Call (866) 320-2646 for an exact quote – estimates are free.
Every asphalt driveway we build is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it’s in writing.
Get a Straight Answer on Your Corte Madera Driveway
Call (866) 320-2646 for a free on-site estimate on asphalt driveways & resurfacing in Corte Madera. A live person answers around the clock, and on the visit we’ll check your base, map the drainage, and give you a written line-item price with no change orders. Homeowners often pair this with a New Detached ADU in Corte Madera or a Junior ADU & Interior Conversion in Corte Madera, and we can quote the whole scope in one visit.
Written by the team at Groundwork Construction Co.