Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in San Bruno, CA: What It Costs and How It Goes In
A wrought or tubular steel iron fence in San Bruno typically runs $3,500 to $9,000 for a standard residential run, and most jobs take two to four days on site once the layout is set. The number moves with linear footage, height, finish, and how much concrete we have to break out along the property line. Call (866) 320-2646 and we’ll walk your lot, measure it properly, and put the range in writing before anyone touches a shovel.
How an Iron Fence Goes In, Stage by Stage
Iron fence work is mostly preparation. The visible part goes fast; the part that decides whether the fence is still plumb in ten years happens underground. Here’s the sequence we follow on a San Bruno job.
Stage 1: Walk, measure, and check the line (day 1)
We measure the full run, note grade changes, and locate the property pins or pull the plat to confirm the line. This is where you decide fence height (4 ft, 5 ft, or 6 ft), post spacing, and whether you want a gate. On sloped lots we plan stepped panels rather than raked ones, because raked iron on a steep grade looks wrong from the street and stresses the welds.
Stage 2: Utility locating and permit filing (days 1 – 10, calendar time)
Before any digging we call 811 so the gas, water, and electrical lines get marked. In San Bruno this step is not optional and not fast. Fence permits here are usually a simple over-the-counter approval, but the review clock is the long pole in the schedule, so we file early. You sign the application; we handle the submittal and the inspection scheduling.
Stage 3: Demo and layout (day 2)
Old fencing comes out, roots and rubble get cleared, and we string the line and mark every post hole. You confirm the final layout and gate swing direction here, before concrete. Moving a post after it’s poured is a real cost, so this is the decision point that protects your budget.
Stage 4: Post setting (days 2 – 3)
Posts go into holes sized to the soil and the load, set in concrete and left to cure. On a 6 ft iron fence with wind exposure, hole depth and diameter are what keep the fence from leaning. This is also where we check clearances near the meter, the sewer cleanout, and any existing hardscape we’re tying into.
Stage 5: Panels, gates, and finish (days 3 – 4)
Rails and pickets get hung, the gate gets fitted with hinges and a latch, and we touch up any scratched finish. Then the final inspection, and a walkthrough with you. You get the written 730-Day Done Right Promise covering workmanship, and we note what to check each year.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Iron fence isn’t one product. These are the real decision points, with the honest trade-off on each.
- Wrought iron vs. tubular steel: True wrought iron is hand-forged, heavier, and repairable by a welder on site, but it costs more and needs periodic painting. Tubular steel is lighter, cheaper, and holds a powder-coat finish well. For most San Bruno lots, tubular steel is the practical pick.
- Powder-coated vs. painted: Powder coating is baked on and resists chipping; it’s the better call in a fog belt. Field paint is cheaper to touch up but needs redoing sooner.
- Galvanized vs. standard steel: Hot-dip galvanizing adds cost but is what keeps the fence from rusting at the welds and post bases when damp air sits on it. Worth it near the coast.
- Height and style: 4 ft reads as decorative; 5 ft is the common residential choice; 6 ft gives privacy and security but raises wind load and post size.
- Gate hardware: A self-closing hinge and a quality latch matter more than the picket pattern. Cheap hinges are the first thing to fail.
What an Iron Fence Costs in San Bruno, CA
Plan on $3,500 to $9,000 for a residential iron fence in San Bruno. That range covers a typical front or side-yard run with one gate. Here’s what pushes a job toward either end:
- Linear footage: The single biggest driver. A 60 ft run sits near the low end; 150 ft with multiple returns pushes toward the top.
- Height and gauge: 6 ft fence in a heavier gauge costs more in material and in post size required to hold it in wind.
- Finish and corrosion protection: Galvanized plus powder coat adds cost but pays back in longevity in this climate.
- Site conditions: Slopes, rock, roots, and old concrete footings all add labor. Removing an existing fence is a separate line item.
- Gates and automation: A pedestrian gate is modest; a driveway gate with an opener is a different budget entirely.
A written estimate from us is line-itemed: footage, gauge, finish, gate count, demo, concrete, permit, and cleanup. What typically isn’t included unless we list it: utility relocation, landscape repair beyond reseeding, and painting of an existing structure. The price you see is the price you pay; there are no change orders for work we should have scoped on day one.
See the difference
Before
After
Before
After
Before
AfterWhat San Bruno Homes Specifically Do to This Job
San Bruno’s permitting reality is shaped by the 2010 PG&E gas pipeline explosion in Crestmoor, which set off a seismic retrofit and rebuilding wave that still runs through the city’s inspection culture today. Crews working in 94066 know the gas line clearance rules, and any digging near that corridor gets planned carefully. That matters for an iron fence because post holes are digging, and a marked-and-cleared line is not a formality here.
The housing stock reinforces it. Crestmoor and the surrounding blocks are dominated by post-WWII single-family homes from the 1940s and ’50s, with a mix of rebuilt and retrofitted structures alongside originals that still carry older foundations and property-line quirks. We measure twice on those lots because fence lines often don’t match the plat. And the fog belt on the Peninsula means damp air sits on steel; powder-coated, galvanized material holds up far better than bare painted iron. If your wider project includes hardscape, homeowners often pair this with Patios, Walkways & Pool Decks in San Bruno, or with ADU Design & Permitting in San Bruno when a new structure changes the property line. For the broader scope, see our Fence Installation in San Bruno page, or our Fence Installation service to see how it fits together. We cover the whole of San Bruno and the surrounding Peninsula.
Serving San Bruno, CA – Our Local Coverage Area
We serve San Bruno and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Iron Fence in San Bruno
Two to four days on site for a typical residential run, with the calendar stretched by utility marking and permit review before we dig. Call (866) 320-2646 and we’ll give you a realistic schedule after we’ve seen the lot.
Usually yes for a fence at or near the property line, and the city reviews it over the counter. We file the application, schedule the inspection, and make sure the height and setback meet code. Call (866) 320-2646 to get the paperwork moving.
$3,500 to $9,000 for a standard residential run, depending on footage, height, finish, and gates. Galvanized and powder-coated material sits toward the higher end but lasts longer in the fog belt. Call (866) 320-2646 for an exact quote; estimates are free.
Far more slowly than bare steel, though no finish is permanent. Galvanizing protects the steel at the welds and post bases, and powder coat sheds the damp air. We’ll tell you honestly how often to expect touch-ups.
Every job is covered by the 730-Day Done Right Promise, and our technicians have up to 12 years of experience on this kind of work. Call (866) 320-2646 with questions before you book.
Get a Free Iron Fence Estimate in San Bruno
Call (866) 320-2646 to schedule your free on-site estimate for an iron fence in San Bruno. A live person answers, 24/7. We’ll measure the run, check the line and grade, talk through height, finish, and gate options, and hand you a line-itemed quote with the permit handled. No pressure, no vague numbers.
Written by the team at Groundwork Construction Co.