Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in San Bruno, CA: Cost, Timeline, and What Actually Happens
A paver driveway in San Bruno typically runs $7,000 – $18,000 for a standard two-car drive, and most jobs take three to six working days from demo to final sweep. The price depends on square footage, base depth, paver grade, and how much of the old surface has to come out. Call (866) 320-2646 for a free on-site estimate with line-item pricing you can read before you commit.
How a Paver Driveway Gets Built Here, Stage by Stage
A paver driveway is mostly the work you never see. The pavers are the last 10% and the part that fails first when the base is rushed. Here’s the real sequence we follow on San Bruno paver driveways, with what you’ll be deciding along the way.
- Day 1 – site check, demo, and haul-off. We mark utilities, saw-cut the edges, and break out the existing concrete or asphalt. A typical two-car drive takes one day to demo and load out. You confirm the layout and the finished grade relative to your garage slab, because that’s what keeps water moving away from the door instead of under it.
- Day 2 – excavation and base prep. We dig to depth (usually 8 – 10 inches total build-up for a residential drive), compact the subgrade, and bring in crushed aggregate in lifts, compacting each one. Skipping lifts is the number one cause of pavers that settle and rut two winters later. This is the stage where a soft or clay-heavy subgrade forces extra base and adds cost.
- Day 3 – edging, geotextile, and bedding sand. We set a rigid edge restraint on both sides, lay separation fabric, and screed the bedding layer to grade. The edge restraint is what stops the field from spreading. It’s also where cheap jobs cut corners and you get a driveway that fans out at the apron.
- Day 4 – 5 – laying the field and cutting. We lay pavers from the bottom of the slope up, cut border and apron pieces on a wet saw, and set the pattern. You choose the pattern and border in advance; anything changed mid-lay means re-cutting and re-laying.
- Day 5 – 6 – compaction, joint sand, and final clean. Plate compaction seats the field, polymeric joint sand locks it, and we sweep and walk it with you. Plan on staying off the drive for 24 hours and keeping vehicles off until the sand cures per the manufacturer’s direction.
Most of the homeowner decisions happen before day 1: paver style, pattern, border, finished grade, and whether the apron or a walkway tie-in is part of the scope. Get those backwards and the schedule slips.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
This is where the number moves most, and where two bids for the same footprint can be $4,000 apart and both be honest.
- Concrete pavers (the standard choice). Interlocking concrete pavers from a manufacturer like Belgard give you the best mix of durability, color choice, and repairability for a Peninsula driveway. A cracked paver lifts out and gets replaced; a cracked slab doesn’t. This is where most San Bruno jobs land.
- Clay brick pavers. Beautiful, longer-lived under freeze-thaw, and more expensive per square foot. Worth it if you want the color to go all the way through the paver rather than sit on the surface. Expect a meaningful premium over concrete pavers.
- Permeable pavers with open joints. A real answer for tight lots and heavy runoff, but they demand a properly designed sub-base and drain rock or they clog and fail. Ask specifically how the water leaves the site before you sign for these.
- Base depth and subgrade. A driveway over a solid, well-compacted base is a different product than the same pavers over an unprepared subgrade. Cheaper bids often shave base depth. Ask for the spec in writing.
- Pattern and border. A running-bond field with a soldier-course border is the value sweet spot. Herringbone and complex borders cost more in cutting time and waste.
- Apron and transitions. The apron, curb cut, and any tie-in to a walkway or Driveway & Pavers scope matter for how the drive reads from the street and how water exits.
Our technicians have up to 12 years of experience setting pavers and prepping base, and that base work is where they earn it. Every job carries the 730-Day Done Right Promise, because a driveway that settles in year two is our problem, not yours.
What Paver Driveways Cost in San Bruno, CA
A paver driveway in San Bruno runs from about $7,000 to $18,000 for a typical residential drive, with the spread driven by square footage, base condition, paver type, and how much transitions and drainage work the site needs. Those numbers are our published ranges, not a teaser.
- Paver driveway installation: $7,000 – $18,000.
- Patio installation if you’re tying the drive into a backyard project: $3,500 – $11,000.
- Sealing (usually a year after install, not day one): $250 – $700.
What pushes a job toward the high end: a large footprint (three-car width or a long run), soft or clay-heavy subgrade that needs deeper base, demolition of thick or reinforced concrete, brick or permeable pavers, complex patterns or multiple borders, and drainage corrections like a channel drain or regrading at the garage. A straightforward replace-in-kind on a solid base lands near the low end.
What’s in a written estimate: demo, haul-off, base materials and compaction, edging, bedding sand, pavers, cuts, joint sand, and cleanup. What’s usually extra: correcting a failed subgrade, adding or relocating drainage, and any permitting the city requires. We put all of it in the quote up front so the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat San Bruno Homes Specifically Do to This Job
San Bruno’s driveway work sits inside a construction market that got reorganized by the 2010 PG&E gas pipeline explosion in the Crestmoor neighborhood. That disaster triggered a mandatory seismic retrofit and rebuilding wave, and it still shapes how permits and inspections run here today. If your driveway touches the public right-of-way or the apron at the curb, plan for city sign-off and, in the Crestmoor blast zone, for PG&E gas line clearance before anyone digs. That clearance is the one thing that can delay a dig schedule, so we confirm it before demo, not after.
The housing stock matters too. Crestmoor and the surrounding blocks are full of post-WWII single-family homes from the 1940s and ’50s, many rebuilt or heavily retrofitted after 2010, which means newer seismic-compliant structures sitting next to older homes that still need foundation bolting. Older driveways here often show the same failure pattern: cracked and settled slabs from shallow, uncompacted base, and water running back toward a garage slab that was poured to a grade nobody rechecked in decades. We see the damp marine-layer side of it as well. San Bruno sits in a fog belt with cool, damp summers and steady onshore wind, and that moisture finds every bad joint and grade. It’s why we take finished grade and drainage seriously on every drive we build. If you’re planning a larger project around this, it’s often part of a full Driveway & Pavers in San Bruno scope, and we cover the wider city on our San Bruno service-area page.
Serving San Bruno, CA – Our Local Coverage Area
We serve San Bruno and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Paver Driveways in San Bruno
Most paver driveways in San Bruno take three to six working days, weather permitting. Demo and base prep eat the first two to three days; laying and jointing take the rest. Call (866) 320-2646 for a firm schedule after we see the site.
If the work stays on private property and doesn’t touch the curb, apron, or right-of-way, a permit is often not required, but it depends on the scope. Anything in the public right-of-way or near the Crestmoor gas line clearance area needs city sign-off. We confirm the permit picture before we quote, so there’s no surprise. Call (866) 320-2646 and we’ll walk through your site.
Sometimes. A paver drive can be laid over an existing slab only if the slab is sound, properly sloped, and thick enough to accept the new build-up, which is uncommon on older San Bruno homes. In most cases we demo and rebuild the base. Estimates are free, so call (866) 320-2646 and we’ll tell you which camp your drive is in.
Between $7,000 and $18,000 for a typical two-car drive, with the final number set by square footage, base condition, paver type, and drainage. Sealing later runs $250 – $700. Call (866) 320-2646 for a written line-item quote.
Every paver driveway we install is covered by the 730-Day Done Right Promise: if it’s not done right, we make it right. That covers workmanship, which is where driveways actually fail. Call (866) 320-2646 for the details in writing.
Get a Free Paver Driveway Estimate in San Bruno
Plan on a free on-site estimate for your paver driveway in San Bruno. Call (866) 320-2646 and a live person answers, day or night. We’ll look at your existing drive, check grade and base, talk through paver and pattern options, and hand you a written line-item quote with upfront pricing. If your project is part of a bigger plan, we can also cover ADU Design & Permitting in San Bruno or a Garage Conversion ADU in San Bruno in the same conversation.
Written by the team at Groundwork Construction Co.