Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Pacifica, CA: What It Costs and How the Job Runs
Metal roofing in Pacifica typically runs $15,000 to $40,000 installed, and most homes are finished in seven to twelve working days once the roof is stripped and the panels are on site. You’re buying a roof that handles salt fog, wind-driven rain and decades of coastal damp without the rot that eats wood shake and the granule loss that chews through asphalt. Call (866) 320-2646 for a free on-site estimate and a written line-item quote.
How a metal roofing job actually moves, stage by stage
Every metal roof we install in Pacifica follows the same order. The stages matter because skipping one is how a metal roof leaks ten years in.
Day 1: tear-off and deck inspection. We strip the old roof down to the sheathing and walk the deck board by board. On 1950s and 60s Pacifica ranch homes this is where surprises live: soft spots around chimneys, rusted-through flashing, and on T1-11-sided split-levels, rot that has crept from the wall into the deck edge. You decide then whether to replace individual boards or re-sheet the whole deck. Re-sheeting runs longer and costs more, but it gives the panels a flat, fastener-ready surface.
Days 2 to 3: underlayment and flashing. We lay a high-temp synthetic underlayment rated for metal, then set the eave trim, valley metal and penetration flashing. On Pacifica’s fog-belt homes we pay extra attention to every penetration and valley, because wind-driven rain off the Pacific finds weak points that a dry inland roof never tests. This is also when we cut in the ridge and hip details.
Days 4 to 8: panel install. Panels go up and get fastened with the correct clip or exposed-fastener system for the profile you chose. Standing seam panels are rolled to length and run eave to ridge with concealed clips. Exposed-fastener panels go down in overlapping sheets. You’ll have chosen panel color and profile back at the estimate; this is where it becomes real.
Day 9: trim, ridge and gutters. Ridge caps, rake trim and any gutter reconnection happen here. If you’re adding guards or a new gutter run, that’s decided before this stage. Most of our Pacifica jobs pair the roof with a fresh gutter line because the salt air and constant fog shorten the life of any metal bracket that wasn’t corrosion-rated.
Day 10 and beyond: final inspection and walkthrough. We test every penetration, check fastener torque, walk the perimeter and clean up. You get a written walkthrough and the 730-Day Done Right Promise behind the work. If your roof ties into a broader project, this is also where we hand off cleanly to the rest of the job, including any Roofing in Pacifica scope you’re coordinating at the same time.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll choose between before we order panels
Metal roofing isn’t one product. The choice you make here decides both the price and how the roof ages in Pacifica’s salt air.
- Standing seam vs. exposed fastener. Standing seam hides fasteners under clips and holds up best in coastal wind and rain, but costs more per square. Exposed-fastener panels (the screw-down type) cost less and install faster, but every screw is a future maintenance point in salt air. On bluff-edge lots we lean standing seam.
- Steel vs. aluminum. Steel panels, including the GAF and CertainTeed lines, are strong and take a coating well, but any cut edge or scratch needs attention to keep rust out. Aluminum resists salt corrosion better and is the smarter pick within a few miles of the water in Linda Mar and Rockaway, but it dents more easily and costs more.
- Kynar finish vs. standard paint. Kynar-type finishes hold color and chalk less over fog-belt years; standard painted finishes fade sooner. The upcharge is modest for the extra lifespan.
- Panel profile and color. A lower rib reads cleaner on a mid-century ranch; a taller rib suits a split-level. Color is cosmetic but the finish matters.
- Concealed vs. exposed fasteners on penetration details. This is a detail you’ll rarely see but it’s the difference between a quiet roof and a leaky one.
We don’t list every brand on every job. We pick the ones that fit the exposure, the profile and your budget, and we put the choice in writing.
What Metal Roofing costs in Pacifica, CA
Most Pacifica metal roofs land between $15,000 and $40,000 all-in. Where your job sits in that range comes down to five things:
- Roof size and pitch. A simple gable on a small ranch home is the low end. Complex hips, dormers and steep sections cost more to install and use more panel.
- Deck condition. A soft or rotted deck adds re-sheeting to the bill. On 1950s-70s Pacifica homes this is common, especially under old chimney flashing.
- Panel system and metal. Standing seam in aluminum is the high end. Exposed-fastener steel is the low end.
- Penetrations and detail work. Skylights, chimneys, valleys and multi-plane roofs add labor.
- Permit scope. A straightforward re-roof permit is a modest line item. Anything that touches structure or triggers coastal review runs higher.
A written estimate from us itemizes the deck work, the panel system, the underlayment, the flashing, the gutters if you’re adding them, and the permit. It excludes anything we haven’t inspected yet, and we tell you that up front rather than surprising you later. Upfront pricing, no surprises is the standard we hold to.
See the difference
Before
After
Before
After
Before
AfterWhat Pacifica homes specifically do to this job
Pacifica is built across the coastal bluffs and steep marine-terrace hillsides along the San Mateo coast, and that changes how a metal roof gets permitted and installed. Bluff-edge and hillside lots routinely deal with coastal development permit conditions and erosion-control measures before work proceeds, and any roof project that touches structure or a cantilevered section can trigger geotechnical scrutiny that an inland Peninsula job never sees. The fog belt, salt-laden onshore winds and heavy winter storms also drive the material call: aluminum panels and corrosion-rated fasteners on the west-facing slopes, careful wind-uplift detailing on every ridge and eave, and a schedule that works around the rainy season so we’re not opening a roof to weather. The housing stock across Rockaway and Linda Mar is a mix of 1950s-70s stucco-and-wood ranch homes and split-levels, many with T1-11 siding and cantilevered structures on sloped lots, and we commonly find deferred decay under old flashing and dry rot in the deck edge on the seaward side. Those findings are why we inspect the deck before we order panels rather than after.
Serving Pacifica, CA – Our Local Coverage Area
We serve Pacifica and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked about Metal Roofing in Pacifica
Most Pacifica homes are finished in seven to twelve working days once the roof is stripped, with the longest stretch being the deck inspection and flashing stages. Weather is the wild card in the fog belt, and we build rain days into the schedule.
Yes, a re-roof on a Pacifica home requires a permit, and bluff-edge or structural work can pull in coastal development conditions as well. We pull the permit and coordinate the inspections so the sign-off is clean.
In most cases, yes. The panel system sits on your existing deck or on new sheathing, and no plumbing or structural moves are needed for a straight re-roof. If we find rot or a structural issue during deck inspection, we’ll walk you through options before we touch anything.
Plan on $15,000 to $40,000 installed, with the low end on a simple exposed-fastener steel roof and the high end on standing seam aluminum with new sheathing and gutters. Call (866) 320-2646 for an exact quote on your home, and the estimate is free.
Work is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction, and the panel finish carries its own manufacturer warranty. We put both in writing before work starts.
Homeowners planning a wider scope often pair this with Window Replacement in Pacifica so the roofline and window trim match, or with Impact Windows & Doors in Pacifica for the same coastal wind and water reasons.
Get a free estimate for Metal Roofing in Pacifica
A free on-site estimate starts with a look at your deck and your current roof, then a written line-item quote you can compare like for like. We answer the phone live, day or night, at (866) 320-2646. We serve Pacifica along with San Bruno, Daly City, Half Moon Bay and San Francisco, and our Roofing service covers the full roof when metal is only part of the plan. Call to schedule.
Written by the team at Groundwork Construction Co.